section plate 中文意思是什麼
section plate
解釋
機座輻板-
From the analysis, some suggestion about joint rigidity design is put forward : 1. joint initial rigidity can be enhanced within the limited range when to increase end - plate thickness ; 2. the rigidity and ultimate moment can be enhanced obviously when to adopt the beam with inclined section or to add axilla at the connections between beam and column ; 3. withm the permissive construction condition, exteriorly extended end - plate inclinedly placed is suggested to be applied firstly ; 4. when the rate of joint rigidity to beam rigidity, that is called, is less than 0. 1, the joints can be regarded as zero - rigidity joints ; on the other hand, if is more than 26, it is rigid connection joints
採用斜截面梁並在樑柱交接處局部加腋能明顯提高節點剛度和梁的抗彎能力； 3在允許的施工條件下，應優先採用外伸式端板斜放節點，有利於提高節點剛度，進而提高節點的抗彎能力； 4節點剛度與其連接構件的剛度比值0 . 1時，可按鉸接節點設計； 26時，可按剛接節點設計。 -
Fluid noise mainly comes from out put pulsation of rate of flow, the main reason of out put pulsation of rate of flow is the instant high pressure return flow that obturation cubage produced when the big round curve pressure transition. the v trough on the port plate can reduce the fluid noise. in this paper, the author based on the acting of dam a river and condensability of liquid and used matlab language as tool to calculate the v trough on the original port plate and drew out the p - t diagrammatic curve and analyzed its shortcoming and improved the design of original v trough and got that the best size of its angle was 12. 3 and its length was 5mm and the cross section was an equilateral triangle
流體噪聲主要來源於輸出流量脈動，造成輸出流量脈動的主要原因是閉死容積在大圓弧段壓力切換時產生的瞬時高壓迴流，在配流盤上開設v型尖槽可降低因高壓迴流而引起的流體噪聲，本文以截流作用和液體的可壓縮性為理論依據，以matlab語言為工具，對原配流盤上的v型尖槽進行了理論計算，繪制出p - t圖線，分析了它的不足，並對原有v型尖槽進行了優化設計，得出了v型尖槽的最佳幾何尺寸：配流盤平面上的v型尖槽的兩邊的夾角為12 . 3 ，槽長5mm ，槽的橫截面為等邊三角形。 -
The bents supporting the four continuous 工 beam plate girders have a cross section shaped like a box.
構架支承著四片工字型板梁，構架的截面為箱型。 -
Analyzing the failure characteristics of steel deck plate paving and the actual use of the testing section which uses epoxy asphalt at jiangyin yangtze river bridge, this paper decides to use epoxy asphalt concrete as the repairing material to prevent pavement from deteriorating
摘要在分析江陰大橋鋼橋面鋪裝破壞特徵的基礎上，結合環氧瀝青混凝土試驗段的實際使用狀況，故決定採用環氧瀝青混凝土對鋪裝層進行預防性維修以避免其繼續惡化。 -
Moreover, aiming at the location of inclined license plate, we have proposed the algorithm based on gray changing characteristic and orientation field. in this section, we discussed in detail the application of mathematical morphology operator in rough locating objective region and introduced the theory and realization method of orientation field. then we used it to detect inclined angel of objective region, finally we can precisely locate and emendate the inclined license plate based on detection result, and so we provided the favorable foundation for segmenting character
此外針對傾斜車牌區域的定位分割問題，提出了基於灰度變化特性和方向場計算的定位演算法，其中詳細討論了數學形態學運算元在目標區域粗定位中的應用，重點介紹了方向場計算理論和實現方法，並將其應用於目標區域傾斜角度的檢測，根據檢測得到的結果進行了傾斜車牌區域的準確定位和校正，為后續的字元分割打下良好的基礎。 -
The section of traditional portal rigid frame are constant cross - section and wedge shape variable cross - section, this paper brings up a component cross - section ? ripple web plate variable cross - section. according to main specially characterist of portal rigid frame, this paper use matlab to work out analytical software. it ' s concrete analysis includes : endogen force and displacement caculation of rigid frame, stability analysis in and out flat surface of rigid frame, geometrical nonlinear analysis of rigid frame. and make comparison between ripple web plate variable cross - section portal rigid frame and constant cross - section rigid frame
傳統的門式剛架的構件截面為等截面和楔形變截面，本論文提出了一種構件截面形式? ?波紋腹板變截面。本論文根據門式剛架的主要特點，利用matlab高級編程語言編制了4個分析軟體，其針對性強，具體分析包括：剛架的內力與位移計算，剛架的平面內與平面外穩定分析，剛架的幾何非線性分析。 -
The cross section is simulated through the mathematics description result, the flank is simulated by choosing the appropriate edge spot in the picture, realizes simulation of the plate texture, and took manchurian ash as an example, analyzed simulated grain
對板材紋理橫斷面通過數學描述結果進行模擬，切面通過在圖像上選擇合適的邊緣點進行模擬，以實現板材紋理的模擬再現，並以水曲柳為例分析模擬紋理。 -
Two hypothesises, different from the traditional viewpoints, about stress distribution in beam section at the connection of beam and end - plate are presented by author to determine the ultimate moment of end - plate connection
其計算過程分為兩步： （ 1 ）計算梁受拉翼緣的極限拉力； （ 2 ）計算端板連接的極限彎矩。 -
The investigation of this paper has grate actual and expansive significance and offer methods for the application of rigid frame. the investigation indicate that the ripple web plate ' s critical stress has great improvement than ordinary flat plate and ripple web plate variable cross - section has a rather superiority than constant cross - section portal rigid frame
本論文所做的研究工作具有很強的現實意義和推廣意義，為門式剛架的應用提供了思路。通過研究表明：波紋腹板的臨界應力比普通的平板有很大提高，而波紋腹板變截面門式剛架與等截面門式剛架進行對比也有較大的優越性。 -
With an analysis of soil liquefaction potential for free field of nanjing metro line 1 under 7 degree earthquake, as well as for excavated field, in line with railway engineering anti - earthquake design specification, dynamic triaxial tests and theoretical analysis using efficient stress method, the author comes to the conclusion that, when metro plate is located at layer s and the layer is thick, liquefied area is at metro bottom plate ; in some local section liquefied area is at metro top plate, or arch sides at the top of metro in most places
摘要採用鐵路工程抗震設計規范、動三軸試驗及有效應力的理論分析相結合的方法，對南京地鐵南北線（ 1號線）區間隧道開挖后其地基土在7度地震情況下的土層液化情況進行分析得出：當隧道底板坐落在5層且5層較厚時的液化區出現在隧道襯砌底板處；局部地段液化區出現在隧道頂部及拱腰；大部分地段的液化區出現在隧道頂板上方。 -
The main results and academic contributions of the dissertation can be summarized as following : 1 ) for the difficulty to obtain the accurate analytical solution of the stress constraints around 3d cracks, detailed 3d fe analyses have been conducted to study the out - of - plane constraint factor tz around a straight through - thickness crack, a quarter - elliptical corner crack and a semi - elliptical crack embedded in an isotropic elastic plate subjected to uniform remote tension loading. the distributions of tz are minutely studied in the forward section of the cracks. strong 3d zones ( tz > 0 ) along the crack front were investigated despite the far field stress - free boundary conditions
全文主要研究內容和學術貢獻如下: 1 .針對一般三維裂紋端部場應力約束準確解析的困難，對均勻拉伸載荷作用下各向同性彈性板中穿透厚度中心直裂紋、半橢圓表面裂紋和1 / 4橢圓角裂紋進行了大量詳細的全場應力三維有限元分析，首次全面分析了非穿透裂紋端部場三維影響區范圍，給出了不同形狀三維裂紋前沿離面應力約束因子tz的數值解，並結合k場平面解給出了非穿透裂紋端部應力場k - tz雙參數描述。 -
And the result shows that the self - excited loads and the flutter derivatives satisfying the linear relationship as to the streamline section - like thin plate
結果表明對薄平板這一類近乎流線體的斷面，自激力與振動參數之間能較好地滿足線性關系。 -
The third section, firstly, we introduce research state of achromatic wave - plate. and then we make a detailed analyse and discuss on each method by which flat - plate birefringent achromatic wave - plates are made and gener
通過上述工作，作者認為今後工作的重點應是進一步提高現有的工藝技術水平、完善實驗條件，使這一方面的工作取得更大突破。 -
Under tensionloading, these gusset plate connections can be susceptible to shear lag failure of thehss since only a part of the tube cross - section is connected to the plate
由於鋼管截面只是部分和鋼板連接，在拉力作用下，管板節點易發生剪切滯后破壞。 -
Knife section and ledger plate of agricultural binders and head - feeding combines
農業用打捆機和頂部送料聯合收割機的切割刀截面和欄頂板 -
Shiyingtan gold deposit is situated in the volcanic island arc zone of northern margin of tarimu plate in the late paleozoic, and is located the west section of xiaorequanzi - dananhu the zone ore forming of cu, ni, au, sn. the condition of geological mineralization in the area is outstanding
石英灘金礦床位於塔里木板塊北緣晚古生帶火山島弧帶，處于小熱泉子-大南湖cu 、 ni 、 au 、 sn成礦帶中西段，區域成礦地質條件優越。 -
Fabrication of the box beam is divided into such parts as reinforcement, formwork, concreting, prestressing, moving and storing of beam, pipe grouting under pressure, end sealing of the beam, water - proof layer on the bridge surface system, protective coating etc. the paper makes description of effective box beam construction technology and workmanship which can be adopted in other projects, such technologies as : manufacturing and fixing of reinforcement, steel reinforcement fixing baseplate, web plate and top plate respectively and lifting the steel skeleton into form, requirements of design and manufacturing and way of utilization for dismantling - erection type formwork and hydraulic formwork, optimization of concrete ratio, concrete pouring process of two ends of beam in priority over the middle, in sequence of first baseplate followed by web plate and top plate at last, concrete pouring in inclined section and in horizontal layer, concrete vibration mainly by external vibrator in assistance with internal vibrator, methods and regulation for steam curing of concrete, dual controls over stress and strain to ensure quality of prestressing workmanship, construction method of effective beam moving by heavy - weight special moving facility, some regulations and key notes about construction of grouting under pressure, beam ends sealing, water - proof layer on the bridge surface system, protective coating
箱梁製造由鋼筋工程、模板工程、混凝土工程、預應力工程、移存梁工程、孔道壓漿工程、梁體封端工程、橋面防水層和保護層工程等施工環節組成。文中介紹的採用胎具製作和綁扎鋼筋，分底腹板和頂板分別綁扎並吊裝鋼筋骨架入模；拆裝式和液壓式兩種模板的設計、製作要求和使用方法；綜合考慮、優化混凝土配合比，混凝土灌注從兩端至中間、先底板、后腹板、再頂板的施工順序和斜向分段、腹板水平分層、附著式振搗為主、插入式搗固為輔的施工工藝，蒸汽養護的方法和規定；應力應變雙控制確保預應力施工質量的施工技術；採用重物移運器有效移梁的施工方法；壓漿、封端、橋面防水層和保護層施工的一些規定和注意事項等都是對箱梁製造行之有效的施工技術和施工方法，並可為以後類似施工作借鑒。 -
The results indicate that the position of sensitive plates is located at the section of middle or upper in tower but not near by feeding plate, and the smaller reflux ratio, the closer overhead of distillation tower. accurate calculation for flash is solved using matlab, and the result is correct and reasonable. complicated multi - components distillation and crude distillation are simulated using chemcad, and results are reasonable about profiles of flow for vapor and liquid as well as temperature in the tower
數值分析的結果表明精餾塔靈敏板位置並不在進料板附近，而是位於精餾段的中上部，且迴流比愈小，愈靠近塔頂;利用matlab實現了蒸餾過程的嚴格計算，與參考值比較，結果正確、合理;藉助于chemcad進行常減壓塔的穩態模擬計算，得出了流量和溫度在塔內的分佈，經過理論分析，結果合理，可為實際生產提供參考。 -
Without the reflux, no rectification would occur in the rectifying section, and the concentration of the overhead product would be no greater than that of the vapor rising from the feed plate
假如沒有迴流，精餾段就無精餾作用，塔頂產品的濃度就不可能高於來自加料板的上升蒸汽的濃度。 -
Based on a series of testing, examination, research and analysis conducted how to lift the speed on nanking section, jinhu road, we explore the possibilities of solving the obstacles of nanking segment of bridges for realizing railroad speed - lift soon due to its subframes and steel plate beams. we produced authentic and convincing data. 3
通過對京滬線南京段部分橋梁為實現鐵路提速而進行的一系列實驗、檢測、研究和分析，探討了成為制約干線提速瓶頸的下承鋼板梁及半穿式鋼桁梁進一步提高運行車速的可能性，為此類結構的橋梁提速提供了可信的依據。
分享友人