shear beam 中文意思是什麼

shear beam 解釋
剪力梁
  • shear : vt vi （sheared 〈古語〉 shore; shorn sheared）1 剪（羊毛等）；修剪（樹木）；剪（呢絨的）長毛。2 ...
  • beam : n 1 梁，棟梁，桁條；（船的）橫梁。2 船幅；（動物、人的）體幅。3 （秤）桿，杠桿，（織機的）卷軸，...
  1. The slope at any section of the actual beam is equal to the shear at corresponding section of the conjugate beam.

    實際梁任何部位的角變等於共軛梁相對應部位的剪力。
  2. The horizontal shear strength of the exterior reinforced concrete beam - column joints is analyzed by the stress of the conterminal beam and column

    摘要針對鋼筋混凝土框架結構，根據與框架外節點相連的梁、柱構件的受力狀態，分析了外節點核心區所受水平剪力。
  3. Considering the special structure of multi - ribbed slab, founding diphase body mechanical model of compound material, strengthening rib beam and rib pillar by equivalent volume ratio of concrete and slice brick, the paper drew elastic compution constant and shear constant. based on the things, the paper simplified isotropy compution model to wall, gave practical design formula of elastic mold and shear mold, provided necessary parameter for practical design formula of elastic rigidity. finally the calculating results agree well with the text results

    結合密肋復合墻板的特殊構造，建立墻板的復合材料二相體力學模型，按照混凝土與砌塊體積比不變原則對肋梁肋柱同時加強，得出墻板的彈性計算常數及剪切常數，在此基礎上，進一步將墻板簡化為各向同性的計算模型，給出墻板彈性模量及剪切模量實用計算公式，為密肋復合墻板的實用彈性剛度計算公式提供必要的參數。
  4. Sliding displacement of beam longitudinal bars in staggered joints is smaller than in ordinary joints, and the beam bar " overstrength in staggered joints is more serious than in ordinary joints when shear force is equal in the two types of joints

    2在節點所受剪力相同的情況下，錯層節點中梁縱筋的粘結滑移比普通節點的要小，梁筋的超強更嚴重。
  5. Tie beam is an important element in frame - shear wall structure

    連梁在框架-剪力墻結構中，也是很重要的一個構件。
  6. The ratio of span - height of an ordinary tie beam is always less 2. 5, so the resisting shear is difficult to achieve

    由於一般連梁跨高比小於2 . 5 ，使得受剪承載力很難滿足。
  7. The shear mechanism, failure mode, deformation capacity, bearing capacity and the reliability of the anchored angle steels of the wrapped steel concrete cast - in - site frame typical story exterior joints under the middle and high axial compression ratio ( n = 0. 3, 0. 5, 0. 6 ), the working performance, failure mode, and the shear capacity of top story joints under the crack moment, the hysteresis characteristic and the dissipation energy capacity of the test joints are all analysed based on the 1 / 4 model pseudo - static tests of five specimens of wrapped steel concrete cast - in - site frame exterior joints, which varied in axial compression ratio, distribution of the beam angle steels and the stirrup ratio

    基於上述分析，本次試驗通過五個外包鋼混凝土邊節點1 4比例模型的偽靜力試驗，以柱的軸壓比、梁角鋼布置形式、配箍率等為主要參數，分析外包鋼混凝土現澆框架一般層邊節點在中高軸壓比（ n = 0 . 3 、 0 . 5 、 0 . 6 ）條件下，節點的抗剪機理、破壞模式、變形能力、承載能力和角鋼錨固的可靠性；分析了頂層邊節點在張開彎矩作用下的工作性能、破壞模式和抗剪承載力；分析了試驗節點的滯回性能和耗能能力。
  8. The work done in this paper is mainly as follows : ( 1 ) the wide beam should intrude to the wall at some length to make the flexural stress uniform along beam section width, thus make full use of the beam ' s bearing capacity and avoid the shear failure in the concrete joint. and it also prevents stress focus and concrete crack in the local shear wall

    關于寬梁與薄墻肢節點，可以得出以下幾點初步結論：寬梁應該深入墻肢一定的深度，以使寬梁截面的彎曲應力沿著梁截面寬度分佈均勻，充分發揮寬梁的抗彎能力，同時避免節點區混凝土的剪切失效，也避免剪力墻的局部因為受到的應力過大而拉裂。
  9. Based on the experiment results, the damage form of abnormal exterior joint are summarized, characteristics of hysteresis curve are studied, the effect of stirrup ratio and height of column section and beam section on anti - shear property of abnormal joint are discussed, working mechanism of abnormal exterior joint is researched, the conclusion that the anti - crack and bearing capacity of abnormal joint are studied by analyzing the minor core of abnormal exterior joint is proposed, the basic data is provided for the design formula of abnormal joints

    根據試驗結果，總結了異型邊節點的破壞形態，研究了節點滯回曲線的特徵，討論了節點核芯配箍率、樑柱截面高度變化對異型邊節點抗剪性能的影響，分析了異型邊節點的受力機理，提出應以「小核芯」為分析單元來研究此類節點抗裂和承載力的建議，為異型節點設計公式的建立提供了基礎數據。
  10. ( 2 ) from the equilibrium conditions of the isolated segment from a beam - column sub - assemblage, it is clarified for the first time that the bond stress along the beam rebars passing through the joint transfers into the column end to balance shear at this column end at the same ratio as that of the compression force in the compressed concrete at beam ends

    通過對樑柱組合體柱脫離體的平衡條件，首次明確了貫穿節點梁筋粘結應力和梁端受壓混凝土的壓力以相同的比例傳入柱端以平衡柱端剪力，從而對節點區的傳力機理重慶大學博士學位論文結出了完整的和具有說服力的解釋。
  11. Analysis of shear lag effect of great cantilever steel box beam

    大懸臂鋼脊骨梁結構模型剪力滯效應探討
  12. Then the judging method is proposed, and the proposed method can consider the stress history and viscosity shear strength of soft soil. in this paper, a fem program dpfbm1. 0 ( double plastic foundation beam method ( version 1. 0 ) ) is established. with this program, the influence of some parameters on foundation excavation is fully studied, the parameters include : compression modulus, cohesive strength, angle of internal ficiction, effective angle of internal friction, the embedded length of the wall and building load

    針對當前國內外彈性地基梁法存在的缺陷，基於對軟土流變性的研究，採取了剪應力判斷彈塑性狀態，以改進和完善基坑工程彈性地基梁法，推導了彈性狀態下地基反力系數的近似解，提出了採用剪應力組合判斷土彈簧彈塑性狀態的方法，編制了相應的彈塑性共同變形法分析程序dpfbm1 . 0 （ doubleplasticfoundationbeammethod （ version1 . 0 ） ） ，並採用該程序分析了壓縮模量、粘聚力、內摩擦角等參數變化對基坑工程的影響。
  13. Hi addition, with regard to the computation of the maximum / minimum moment, shear force, settlement and foundation reaction of pile capping beam, the randomness of both pile capacity and foundation modulus are statistically analyzed in virtue of the method ? monte carlo. accordingly, the random probability analysis of the internal force of pile capping beam can be achieved

    並通過蒙特卡洛（ montecarlo ）法對基樁承載力、土體基床系數的隨機性進行統計分析，獲得了承臺梁彎矩、剪力、沉降以及基底反力的最大（小）值，從而實現了樁基承臺梁內力計算的隨機概率分析。
  14. Secondly, this paper made some theoretic researches on its engineering classfication and applicable scope for this technology ; then combining with project example, this paper carried out scheme design for this technology, and compared some different kinds of underpinning scheme and node and structure design, and put forward the method of " reinforcce steel bar through column " to build pile cap beam, " resistant bend and shear anchored reinforce steel bar " to strengthen column consolidation effect, and the method of " steel plate hoop " to build reinforcing bar connection of the foundation beam, etc. in the process of the consturction scheme research and implement, this paper synthetically elaborated the organizaton for project construction, put forward the construction technical measure of specific aim on the artificial pile, and pile cap beam, and underground adding layer and structure stabilization, and overall structure stabilization and so on. for this project, adopt reinforcing bar concrete to brace hole wall to ensure the safety of engineering in the artificial pile construction, use flexible connection catch to make the cage hoisting easier to simplify the construction process, use the method of earthwork statified symmetrical balance in the process of underground adding layer excavation

    本文首先對于基礎托換與結構加固技術的目的和意義、國內外發展狀況進行了綜合闡述；其次對該項技術工程分類及適應范圍進行了理論上的分析研究；然後結合工程實例對該項技術進行了方案設計，對比幾種不同的托換方案和節點及構造設計，提出了「通筋穿柱法」做承臺梁， 「抗彎抗剪錨筋法」強化柱加固效果， 「鋼板箍法」做地基梁鋼筋連接點等多項技術；在施工方案的研究和實施過程中，對于工程施工組織進行綜合闡述，並就人工挖孔樁、承臺梁、地下加層及結構加固、整體結構穩定等專項施工方案提出有針對性的施工技術措施，人工挖孔樁施工採用鋼筋砼護壁確保挖孔樁的安全成型，使用柔性連接鉤進行鋼筋籠吊裝簡化施工工序；承臺梁施工採用梁主筋橫穿柱身化學膠錨固等；地下加層綜合施工技術採用土方分層對稱平衡開挖，分段挖土做筏基結構自穩等；最後對于該工程實施后的效果分析，說明該項綜合施工技術的可行性。
  15. 4. axial compressive ratio is advantageous to seismic behavior of staggered joints. it can improve joints first crashing loads, shear resistance capacity and reduce the sliding displacement of beam bars

    軸壓比對節點的抗震性能有利，它可以提高節點的初裂荷載、抗剪承載力、減小節點中梁筋的粘結滑移量。
  16. The detection of a 11 - layers frame shear wall structure shows that the concrete strength of the seventh partial wall columns and the eighth partial beam and floor plate in that building are very low

    摘要對某11層框架剪力墻結構住宅工程結構檢測時，發現第7層部分墻柱和第8層部分梁板混凝土強度嚴重不足。
  17. Member shear beam member shear beam

    構件梁剪切梁
  18. Member shear beam load shear beam

    構件剪切梁
  19. Tecsis load shear beam

    Tecsis測壓梁剪切梁
  20. Mechanical vibration and shock - characterization of the dynamic mechanical properties of visco - elastic materials - cantilever shear beam method

    機械振動和沖擊.粘彈性材料的動態機械性能特徵.懸臂剪切梁法
分享友人
分享到 Line

分享到臉書