size of wheel 中文意思是什麼
size of wheel
解釋
砂輪尺寸-
With the fea software ansys and shell element which has high - precision, this dissertation optimize the size and thickness of skeleton section and seek steel pipe which still have strength and stiffness surplus under static state working condition : sinkage of 240mm of rear wheel. it ' s fully loaded in the state of static bending and torsion. after that, amelioration is achieved for even strength design
本課題運用ansys有限元分析軟體，並且使用精度較高的shell殼單元作為建模單元，在靜態條件下，通過對左右後輪下沉240mm的彎扭聯合工況的模擬分析，尋找出骨架中存在強度和剛度富裕的構件，使之達到輕量化改進的目的。 -
Check the gear wheel drive in the groove of the wall, select four gear wheel ( red pinion is not used ) of different size for use, load heavy gear wheel, times of heavy gear wheel, times of light gear wheel, minimum gear wheel most onto separately from left to right, make gear wheel hand in, form each other, leave behind, operate a switch, drive, finish
檢查墻壁凹槽中的齒輪驅動裝置，選用大小不同的四個齒輪（紅色的小齒輪不用） ，從左到右分別裝上最大的齒輪、次大的齒輪、次小的齒輪、最小的齒輪，並使齒輪間相互交結，拉下拉閘，驅動完成。 -
Shandong weituo group co., ltd ( swt ) is the cradle of small - size 4 - wheel tractors and a large - scale enterprise of producing tractors in china with registered capital 149, 500, 000 rmb
山東濰坊拖拉機廠集團有限公司是中國小四輪拖拉機的發源地，是中國生產拖拉機的大型骨幹企業。 -
Sand mulling device is composed of runner wheel, mulling rotor and scraper, fit for mixing damp system sand for machine moulding in large size or medium size foundry workshop
該機的混砂裝置由輾輪混砂轉子刮板等部分組成。主要用於大中型鑄造車間混制機器造型用濕型單一砂。 -
The results show that, when increasing the feed rate of the grinding wheel, decreasing the rotating speed of the wafer chuck table and using coarser grit grinding wheel, the material removal rate in the wafer rotating grinding increase, the feed rate of the grinding wheel has greater influence on the material removal rate ; when suitably increasing the rotating speed of the grinding wheel, decreasing the feed rate of the grinding wheel and using finer grit grinding wheel, the wafer surface roughness can be reduced ; there exists a critical rotating speed of the grinding wheel ( about 2300rpm ), beyond which the material removal rate evidently decreases and the spindle motor current and wafer surface roughness steeply increase ; when the grit size of the grinding wheel is finer than # 2000, the material removal rate decreases and the wafer surface roughness has no obvious improvement
研究結果表明，增大砂輪軸向進給速度和減小工件轉速，採用粗粒度砂輪有利於提高磨削矽片的材料去除率，砂輪軸向進給速度對材料去除率的影響最為顯著；適當增大砂輪轉速，減小砂輪軸向進給速度，採用細粒度砂輪可以減小磨削表面粗糙度；在其它條件一定的情況下，砂輪速度超過一定值會導致材料去除率減小，主軸電機電流急劇增大，表面粗糙度變差；採用比# 2000粒度更細的砂輪磨削時，材料去除率減小，矽片表面粗糙度沒有明顯改善。 -
By using a wafer - rotating grinding machine, the influence of the main process factors including grit size of diamond grinding wheel, rotating speed of the wafer chuck table, rotating speed and the down feed rate of the cup grinding wheel on the material removal rate, spindle motor current and wafer surface roughness in grinding large size wafer are experimentally investigated
摘要利用基於自旋轉磨削原理的矽片超精密磨床，通過試驗研究了砂輪粒度、砂輪轉速、工件轉速及砂輪進給速度等主要因素對材料去除率、砂輪主軸電機電流以及磨削后矽片表面粗糙度的影響關系。 -
And use this optimization program computate the boom structure shape of heavy bucket - wheel stacker & reclaimer ; based on shape optimization, we use second optimization technology to optimize structure section size. the optimization results are satisfied. the computation indicates that considering the geometric nonlinear element can enhance the calculation efficiency and precision of optimization design evidently in sensitivity analysis
編制了空間剛架結構優化設計程序（ 3dfem - opt . for ） ，並利用編制的優化程序對某大型斗輪堆/取料機前臂架在最大應力約束條件下，進行結構形狀優化設計;在形狀優化的基礎上，採用二次優化技術，對結構的截面尺寸進行了優化。 -
Input the suitable figures according to the size of your bicycle wheel ( see following table )
輸入與你的自行車輪徑相適宜的參數。 -
5 design for small gear relates to hatch size of control - pan -, worm - wheel ratio and fact abrasion quantum of brake block. this article gives their compute formula
5小齒輪的設計與控制盤開口尺寸、蝸輪蝸桿的傳動比和制動襯片的實際磨損量有關，文中給出了它們的計算公式。
分享友人