strain-gauge test 中文意思是什麼
strain-gauge test
解釋
應變儀測試-
For confirming the results, a full - size model ( dj / dj = 0. 6, t / t = 1. 5 ) was analyzed by means of strain gauge test. the reliability of finite element analysis was proved because the results basically accorded with that of the test. secondly, in this paper, in order to carry out a fair assessment of the reinforcement design on spherical shell with transnormal nozzle, a comparison of reinforcement method was done between jb4732 - 1995 steel pressure vessels ? esign by analysis appendix a4 and hg20582 - 1998 specification for stress calculation of steel chemical vessels
為了驗證ansys分析結果的可靠性，對其中一組參數下（開孔率0 . 6 、厚度比1 . 5 ）的模型容器，採用電測法進行了應力測試，並將得到的實驗結果與有限元結果進行了比較，二者在應力分佈狀況和大小上均基本吻合，證明此種結構運用ansys進行分析，其結果是完全可靠的。 -
At last, we introduced the design of demodulation device of white - light interferometer modulation / demodulation fiber - optic fabry - perot sensor. we provide the ways to improve the property of sensor. we performed a experiment to test the capability of our sensor to strain gauge, and applied our sensor into study on carbon fiber material temperature property
最後討論了白光干涉型光纖fp傳感器信號解調裝置的設計，提出了改進該種傳感器性能的方法，並對該傳感器系統與電阻應變片作了對比實驗，將該種傳感器用於了碳纖維材料的溫度性能實驗中。 -
Firstly, the strain gauge method was used to measure the time difference of stress wave passing through two gauges adhered on the surface of test piece and also their main frequencies secondly, a 3 - component dynamometer was used to measure the resonant frequency of timber six kinds of full size timber were used for test
本研究旨在研發兩種新的應力波計測技術，其一為利用應變規來測定兩標點間之應力波傳遞時間差及試材之共振頻率，藉以計算試材之音速及動彈性系數，其二為利用三向動力計來測定試材之共振頻率。 -
Abstract : the results of hi - lo strain - gauge test on 9 dead - load testing piles are analyzed. the bearing strength of single piles is evaluated preliminarily by using high strain and low strain process and conditions for correlating dynamic and dead loads and technical factors affecting the test accuracy are discussed
文摘:通過對一組靜載試驗樁高低應變動測結果的分析，對高應變法、低應變法檢測單樁承載力的可靠性作出了初步評價，並對動靜對比成立的條件及影響其測試準確性的一些技術因素進行了探討。 -
Methods of test for length change of mortar and concrete part 2 : method with contact - type strain gauge
灰漿和混凝土長度變化的試驗方法.第2部分:接觸式應變儀檢測法 -
Wind tunnel strain - gauge balance is the most popular measuring device in the aerodynamic force - measuring test in the wind tunnels, and the performance of the balance would effects the tests results on accuracy
風洞應變天平，是目前國內外各類型風洞在氣動力測量試驗中廣泛採用的測量裝置，其性能指標直接影響測力試驗數據的精準度。 -
Meanwhile, the mathematic modeling on optimal placement of sensor for static test is founded, and the strain gauge network optimal design method for girder bridge static test is also given, which has been verified by an instance
同時還建立了靜力實驗傳感器布置優化設計的數學模型，提出了梁式橋靜力應變傳感器網路優化設計方法，並用實例證明了該方法的合理性。 -
The technique that used to measure the mechanical properties for mems is different from the traditional one considering the size scale. a uniaxial tension test system for test the mechanical property of mems materials is presented in this thesis. the strain is measured by interference strain / displacement gauge ( isdg )
本文介紹了新近研製的用於測量微電子機械繫統mems材料的機械性能的單軸拉伸試驗系統，採用激光干涉技術測量試樣應變，得到材料從開始變形直至破壞的全歷程應力應變曲線。 -
There is a detailed introduction to the theory, characteristic, equipment and method of the strain gauge in this paper. the use of the disturbance preventing can eliminate some disturbances effectively during the flight test, and has some satisfied results
本文詳細介紹了應變片的工作原理及其工作特性、測量設備、測試方法，實際測量中採用了預防干擾的措施，解決了飛行測量中部分干擾的問題，取得很好的效果。
分享友人