structural connection 中文意思是什麼

structural connection 解釋
結構接頭
  1. Pseudo - static force testing of 1 : 2 scale models of a steel frame with dog - bone connections is first carried out in china in order to obtain elastic - plastic behavior of dog - bone connections steel frames under cyclic loading as well as to analyze collapse characteristic after structural ultimate strength has lost. the influence of dog - bone connection on the coming order of plastic hinges and failure characteristic of steel frame, and the influence of dog - bone ' s shape and position on the behavior of structure is obtained

    通過試驗考察了狗骨式連接平面鋼框架結構在循環荷載作用下的彈塑性性能;了解狗骨式連接對結構塑性鉸出現的順序以及結構破壞形態的影響;了解節點處與狗骨處應力發展狀況，探討狗骨削弱的形狀和削弱位置對節點性能的影響。
  2. Finally, a structural new radome is developed and the new radome is analyzed in strength under structural and thermal loads in missile flight. the results show that the new radome has a much improved structural reliability but with the connection design of the metal tip leaving much to be improved. this paper has a reference value for development of air - to - air missile radomes

    最後，在前面工作的基礎上，提交了一個新型導彈天線罩的結構設計方案，並對該新方案進行了導彈飛行中靜熱聯合載荷作用下的強度分析，結果表明，新方案結構可靠性有了較大的提高，但包括改進方案在內的雨蝕頭的連接設計存在一定不足及隱患。
  3. Abstract : according to the deformation or fracture caused by uneven loads on the structural connection, the smart structure with sensible and regulative functions has been proposed to be used in bolt groups. the smart structure is constituted with the auto - even - load connecting component made of the shape memory alloy material. the mechanical behavior of the auto - even - load component in the bolt groups is analyszed. its auto - even - load and the regulative principle to prevent the fracture are also studied

    文摘:本文針對結構聯接受力不均易產生變形或破裂等問題，提出了在螺栓組中加裝由形狀記憶合金材料製作的自動均載傳力件構成具有感知和調節功能的智能結構，並對螺栓組聯接加裝均載傳力件后的均載防斷功能進行了力學特性分析，特別是對螺栓組傳力件自動均載和防斷的調節原理進行了研究，最後進行了實驗驗證。
  4. Subject to the physical characteristic of parts, a simplified structural model shall be given by simulation run environment. the structure of component model shall be constituted with the exterior characteristic interface, physical performance interface and simulate control interface in accordance with the connection standard of simulation component for component model realization and with clear function and easily extention

    針對硬體部件的物理特性和模擬環境下的特殊要求，模擬運行環境給出簡潔的構件模型，由構件的外部屬性介面、功能屬性介面和模擬控制屬性介面組成，按照構件模型實現的模擬構件介面標準、功能明確、易於擴展。
  5. On the basis of statistic data, this article analyzed the structural conditions of the tourism industry in hubei province and, by means of shift - share analysis and grey - relation analysis, discussed the structure competition advantages and the connection between the income of different sections and the gross income

    摘要以湖北省旅遊統計數據為基礎，綜合運用偏離份額分析法和灰色關聯分析法，對湖北省旅遊產業結構的競爭優勢以及旅遊產業各部門收入與旅遊總收入之間的關聯性展開了分析。
  6. The application of the structural teaching model is discussed and a teaching model ? ? structural classroom teaching model on electromagnetism in the teaching of general physics is given. this model is based on the principles of education model, and the fundamental idea of structuralism of discipline and it is also the summary of teaching experience. this model uses a block diagram to summarize the knowledge structure. the knowledge structure includes concepts, theorems, laws and so on. there are three implementation steps in this model ： the first to analyse the content to teach and find the develop meat course of the subject. the second is to emphasize concepts, especially the concept of field. the last is mastering the laws, especially the connection between them. the aim of giving the teaching model is to deepen the teaching reforming and intensify the teaching and learning of the basic knowledge of physics

    以教育模式的基本原理及學科結構主義的基本思想為指導，在總結教學經驗的基礎上，對結構化教學模式在學科教學中的應用進行了深入的探討，提出了普通物理教學中的電磁學結構化課堂教學模式.該模式強調用方框圖概括知識結構，把整個電磁學的知識結構即電磁學的概念、定理、定律及電磁場的性質等概括為一張方框圖，根據方框圖制定了該模式的實施步驟為三步：第一，掌握主線，弄清脈絡;第二，掌握概念，場是關鍵;第三，掌握規律，重在聯系電磁學結構化課堂教學模式旨在深化教學改革，加強物理學基礎知識的教學和學習
  7. Analyzed with pkpm the effect of connection columns on the hoist room structural cracks and the effect of temperature differences on hoist room structure in the structural design of huangtangjia power station, as well as the valuation of wind load in the design

    摘要應用pkpm程序分析了黃塘甲水電站啟閉機房結構設計中貫通柱對啟閉機房結構裂縫的影響，溫差效應對啟閉機房結構的影響，並對風荷載取值進行分析。
  8. The connection of steel structures is an important part for the steel structural member. the types of connections which are commonly used in practical engineering, such as welding, bolting, high - strength bolting and mixed connections are discussed in this paper

    鋼結構連接是鋼結構構件的重要組成部分，本文結合工程實踐，著重對鋼結構中廣泛應用的連接形式，如焊接連接、普通螺栓連接、高強度螺栓連接和混合連接等進行了敘述。
  9. After confirming system goal, according to overall design rule, system overall design is to carry out system overall logic structural design and software and hardware design of system ; system function design includes data to get and edit modular, data inquiry and statistics modular, overall estimetion modular, function district estimetion modular and typical cadastral parcel estimetion modular, land optimization deployment modular as well as urban land grade and evaluation modular ; database detailed design includes the design of space database and property database as well as design for the connection of space data and property data ; system application model analysis mainly explains models for intensivism degree, unit comprehensive value, land area potential, land benifit potential as well as typical cadastral parcel estimetion

    系統總體設計是在確定系統目標后，按照總體設計準則，進行系統總體邏輯結構設計及系統的軟硬體配置設計；系統功能設計包括數據獲取及編輯模塊、數據查詢統計模塊、總體評價模塊、功能區評價模塊、樣地評價模塊、土地優化配置模塊以及城鎮土地定級估價模塊等七大模塊的設計；數據庫詳細設計包括空間數據庫、屬性數據庫的設計以及空間數據與屬性數據的連接設計；系統應用模型分析部分主要對于集約度模型、單元綜合分值計算模型、用地面積潛力測算模型、用地效益潛力測算模型以及樣地潛力評價模型做出了分析解釋。
  10. Because of cold formed thin - walled light steel structure ' s special construction, if draws the mechanics model according to the rigid connection frame, that will be over - evaluated the bearing capacity of the structure ; and if draws mechanics model according to the pinned connection frame, when the foot also adopts this kind of structural form according to the frame connections, that will form organization, and the calculation will be unable to go on

    由於冷彎薄壁輕鋼龍骨結構體系的特殊構造，如果按節點剛接的框架提取力學模型，將高估結構的承載能力；而如果按節點鉸接的排架提取力學模型，當柱腳也採用此種構造形式時，又會形成機構，使計算無法進行。
  11. The early studies are mostly focused on the method of gluing piezoceramics on structural surfaces, which has some disadvantages such as difficulties to protect the ceramics and the connection wires, bad coupling with only one surface glued on the base materials, low signal - to - noise ratio etc. these problems can be solved using the embedded piezoceramics, and furthermore, the piezoceramics can be placed in the optimal positions, especially in the optimal deepness for the piezo - actuators, according to an optimization algorithm befor e they are embedded, so the actuator effects and sensor signals are thereby enhanced

    早期的研究主要集中在表面粘貼壓電片的結構，表面粘貼壓電片具有一些無法克服的缺點。本文著重進行利用埋入復合材料結構的壓電傳感器和壓電驅動器對其振動進行主動控制的相關理論和實驗研究，並介紹其相應結果。埋入型壓電材料的優點主要是能保護壓電傳感器和作動器及其連線、增強壓電材料和基體材料的耦合、優化埋入壓電陶瓷的深度和厚度可增強壓電傳感器的測量信號並提高信噪比等。
  12. Steel frame with welding joint easily occur brittle collapse because of having a low ductility at joints then ， a semi - rigid connected steel frame has large the energy absorption capacity which can resist dynamic loads and the using steel qualities of bracing system and joints are small so adopting a semi - rigid jointed steel frame is economical and stable but for semi - rigid connections are complex and variable ， in conventional analysis and design of steel structures ， it is usually assumed that the connections between columns and beams are either rigid or pinned the analysis of steel frames adopting the assumption can simplify the procedure of analysis and design ， but cannot precisely reflect structural practical circumstance and the errors of calculating results are large ， even ， get incorrect conclusions semi - rigid connection was referred to in chinese code for design of steel structures ( 2001 ， 10 ) ， however ， it isn ’ t specified how to apply semi - rigid joints in design in fact it cannot be carry out the purpose of the paper give a calculating method that accords practical engineering and easily put into effect worthwhile it is going to promote the development of semi - rigid jointed steel frame in design and heighten structural stability in the paper ， at first some commonly employed methods for the modeling of connection behavior are introduced richard abbott function modeling of connection is adopted for extended end plate bolted connection by the 34 test data comparing to regression analysis indicate richard - abbott function modeling of connection represents an excellent fit to test data then after a semi - rigid joint behavior can be modeled as a finite stiffness rotation spring ， base on rotation and displacement equation derive the element stiffness matrixes with semi - rigid connections where the effects ofj ointed flexibility geometric non - linearity and shear forces in the connection deformations have been considered in and fixed - end forces are modified finally, a program for calculating semi - rigid with incremental - iterative method has been

    本文的目的就是為半剛性連接鋼框架的設計提供一種既符合工程實際又簡便易行的計算方法，供規范使用過程的補充、延伸或參考；同時，也將促進半剛性連接鋼框架設計技術的發展，為提高結構安全性能、節省工程成本發揮應有的作用。本文首先介紹了常見的幾種應用較為廣泛的樑柱連接彎矩轉角關系模型，在分析比較的基礎上，選用richard ? abbott函數模型作為外伸端板連接彎矩轉角關系模型，通過對34個外伸端板連接的實驗數據與回歸分析得到的參數比較可知，經回歸分析得到的此模型參數與實驗數據符合較好。然後用彈簧表徵連接點的轉動剛度，根據梁的轉角位移方程推導出半剛性連接的剛度矩陣，在單元剛度矩陣中考慮了節點柔性、幾何非線性和剪切變形的影響，並對固端力進行了修正，最後用增量迭代法編制有限元程序進行計算和分析。
  13. According to the nonhomogeneous anisotropic elastic theory, a calculation model of composite material plate with circular hole in common structural connection section was developed

    摘要針對工程中常見的連接結構中含圓孔的復合材料板，根據非均質各向異性彈性理論建立計算模型。
  14. Estimation of parallel connection structural reliability for exponential strength and mobve distributed stress

    分佈強度為指數分佈下串聯結構可靠度的估計
  15. 4 pseudo - static force testing of 1 : 2 scale models including three steel frame two with semi - rigid connection and one with dog - bone connection are first carried out in china in order to obtain elastic - plastic behavior of semi - rigid connections and dog - bone connections steel frames under cyclic loading as well as to analyze collapse characteristic and the coming order of plastic hinges of the structure with different connections after structural ultimate strength has lost and conditions of stress development in the dog - bone, and the reason of the brittle failure in the rigid connections is obtained

    同時探討了連接形式對鋼框架性能的影響。 4進行了兩榀半剛性連接和一榀狗骨式連接平面鋼框架結構的擬靜力試驗。通過試驗考察了半剛性連接和狗骨式連接平面鋼框架結構在循環荷載作用下的彈塑性性能；了解了不同連接形式的結構在達到極限承載力后的破壞形態和塑性鉸出現的順序。
  16. Involving interaction of gasket, bolts and flange rings, the load - deformation and the structural fuzzy reliability of each component are analyzed in the case of ideality, external loads and creep - relaxation respectively. and then, the sealing fuzzy reliability of the flanged connection system is researched. the function of each part of genetic algorithm is analyzed in application to nonlinear unconstrained and constrained optimization

    本文將墊片、螺栓和法蘭作為一個相互作用的整體，比較深入地分析了理想情況下、有外載作用及蠕變-鬆弛影響下，平墊片和0形圈這兩種典型的火箭發動機法蘭連接系統各元件的載荷與變形、元件的結構可靠度和火箭發動機法蘭系統的密封可靠度。
分享友人
分享到 Line

分享到臉書