suction inlet 中文意思是什麼
suction inlet
解釋
吸力進氣口-
Reynolds numbers ( based on average velocity at passage inlet and hydraulic diameter of the passage ) are changing from 20000 to 80000 and the extraction ratios ( suction ratios, sr ) are changing from 0. 30 to 0. 60 for each test model. so the influences of reynolds numbers, suction ratios and etc. on the discharge coefficients and pressure loss characterist ics are also presented. flow fields of typical passages are visualized with the flow visualization techniques and measured with hot - wire anemometer
對每一種通道結構，實驗在不同通道進口雷諾數（ re = 20000 、 40000 、 60000 、 80000 ）和不同通道總出流比（ sr = 0 . 30 、 0 . 45 、 0 . 60 ）下進行，以研究這兩個流動參數及其它相應變化的參數（氣膜孔的雷諾數re _ h 、氣膜孔與通道的動量比i等）對出流特性和流阻特性的影響規律。 -
Experiment of boundary layer suction in serpentine inlet under ground running
蛇形進氣道地面工作狀態附面層抽吸試驗研究 -
The process of effluent flow during loading in self - propelled trailing suction hopper dredgers was simulated by way of physical modeling and was measured and analyzed by using the flow rate and concentration of spoil in the hoppers, particle sizes of sediments at the inlet and outlet of the effluent flow pipe and hopper volume as the major control parameters
摘要通過物理模型試驗模擬自航耙吸挖泥船裝艙溢流施工過程，以艙內流速、艙內濃度、溢流進出口泥沙粒徑、裝艙量幾方面為主要控制因素，進行實測、分析，並比較自航耙4種常用裝艙裝置的消能效果。 -
This control system adopts creditable plc for real control ; it sends many simulating signals collected by old sand temperature of inlet, suction opening temperature of double disk, inner sand temperature of double disk, current of mainframe and current of fan ; meanwhile, the operation signal and switching value signal outputted by material movement transducer is inputted to switching value module of plc ; it gets evidence of water feeding after cpu account ; the operation result of cpu is outputted by switching value of plc to control unlock combination of coarse, middle and thin water feeding electromagnetically operated valve and then gets different water feeding quantity
該控制系統採用高可靠性的plc可編程序控制器進行實時控制，傳感器所採集的入口舊砂溫度雙盤抽風口溫度雙盤內砂溫主電機電流及鼓風機電流等模擬量信號直接輸入plc的模擬量採集模塊，同時加砂設備運轉信號及加砂設備物料移動檢測傳感器發出的開關量信號輸入plc的開關量模塊，由cpu獲取經運算而得到加水計算依據， cpu運算結果直接由plc的開關量輸出控制粗中細加水電磁閥的開啟組合，而得到不同的加水量。 -
The hydraulic analysis of pump for suction penetration of bucket foundation as well as the pressure head relation between bucket cavity and pump inlet for different water depths and different pump mounting heights are described in this paper
對桶形基礎平臺負壓沉貫過程中汲水泵機進行了初步水力分析，討論了不同水深、不同泵機安裝高度情況下，桶腔和泵機進口之間的壓頭關系。 -
Margin waste suction inlet in lower suction method, computerized automatic positioning
紙邊廢紙吸入口採下吸式.電腦自動定位 -
As an inlet structure, the forbay is an important part of the pumping station. the pressurized forbay, close in top structure, is a kind of particular forbay in which water is pressurized. based on the integral hydraulic model test of shanghai changqiao waterwork ' s water - transport pumping station, some research on the hydraulic characteristics of the pressurized forbay has been done in the paper. the main content is listed as follows : l. the hydraulic characteristics of the pressurized forbay in different water supply combination and different pump unit combination without divertion measure, and the reason of the poor flow state. 2. the hydraulic characteristics of the pressurized forbay with diversion pier, and the reason why the flow state can be improved. 3. the experimental research on the critical air suction condition of the pressurized forbay
本文基於上海長橋自來水廠改造工程送水泵站整體水力模型試驗，對有壓前池的水力特性進行了研究，研究的主要內容如下： 1 、無導流措施的有壓前池在不同供水組合及不同機組開機組合條件下的水力特性，並分析了流態較差的原因； 2 、加設導流墩後有壓前池的水力特性，以及加設導流墩流態改善的原因; 3 、有壓前池進氣臨界條件的試驗研究； 4 、水泵進氣以後水泵性能的討論。 -
According as the mathematic model near the inlet of the 1750m3 / h cutter suction dredger, by researching the method of calculating the slop ' s specific gravity and volume concentration, the thesis adopted instant interactive mode and developed the optimized dredging operation guiding and training system, which has outstanding instructional quality
根據1750m ~ 3 h絞吸式挖泥船吸口處泥漿形成過程的數學模型，通過對計算泥漿比重及體積濃度的方法進行專門研究，採用即時交互方式，按疏浚作業優化操作步驟開發出指導性強的疏浚作業優化操作提示系統。
分享友人