through crack 中文意思是什麼

through crack 解釋
穿透裂紋
  • through : 副詞1 穿過,通過,經歷;從頭到尾,完全,全部;到最後,到底,徹底;透;完畢。 2 出來。 adj 1 直通...
  • crack : vt 1 使破裂;敲破,敲碎,砸碎(陶器等);嗑(瓜子等);【化學】裂化(石油等)。2 把(槍打得、鞭子...
  1. In this system, the oil pipe be locally magnetized through the longitudial and circumferential direction, the oil pipe be circumvolved by the electromotor, the detector will has a linear movement on the surface of the pipe, so it can realize the combined testing of horizontal flaw ( cankerous pits and cankerous holes etc. ) and vertical flaw ( pole flaw and crack etc )

    該系統在油管局部實施軸向和周向磁化,油管由電機主軸帶動旋轉,檢測探頭緊貼油管直線運動,從而實現對腐蝕坑、腐蝕孔等橫向缺陷和桿狀損傷、劈縫等縱向缺陷的綜合檢測。
  2. The rain-water dripped through a crack on the ceiling.

    雨水從天花板的裂縫中漏下來。
  3. In ely place, baggot street, duke s lawn, thence through merrion green up to holles street, a swash of water running that was before bonedry and not one chair or coach or fiacre seen about but no more crack after that first

    自伊利廣場巴戈特街與杜克草坪,穿過梅里翁草地,直至霍爾街。當初乾涸裂,而今猛水奔流,轎子公共馬車出租小馬車,一概不見蹤影。然而最初之霹靂后,即不再聞雷聲。
  4. : 36 < kth < 37 mpa / m3 / 2, 42 < kih < 44mpa / m3 / 2, 51 < kc < 52 mpa / m3 / 2 through the sem fractography, it is know that the susceptibility to brittle failure at room temperature is more than below 100 ?. and the susceptibility to brittle failure increase with hydrogen increasing, under the sustained loading, ductile cracking appears. the quantity of brittle cracking is more with crack growth

    T44mpa m 『 q , sl lt52mpa in 』 」斷口分析表明,該合金充氫后其室溫時的氫脆敏感性大於100oc時的氫脆敏感性;且隨氫含量升高,氫脆敏感性增加:在恆載荷的作用下,該合金裂二紋開始擴展時顯示的是韌性起裂;隨裂紋增長,試樣脆性斷裂的比例增大。
  5. Using material, which composition is basically same to substrates through grinding, and then dipping its slurry on substrate with heating 800 and then sintering at 1400. there was no crack on the surface of coating. distinguish between coating and substrate may use sem, from sem micrographs of cross section of coating, there is gradated pore structure, while pore - forming agent is no good for coating

    採用與基體成分相同的原料配製的料漿在經800燒成的素坯上成膜,燒成后發現,添加成孔劑的料漿成膜后表面易於開裂,而未加成孔劑的料漿成膜效果較好。
  6. Gasped huckleberry. " i dono - peep through the crack

    「我不知道,你從縫里往外瞅瞅。
  7. A quarter of an hour afterwards the postilion, having been put in the right road, passed with a crack of his whip through the gateway of the barri

    一刻鐘以後馬夫已拐上正道,揚鞭通過了聖馬丁城柵的城門。
  8. Through the dry and wet cycling experiment on unmarred beam and pre - cracked beam, the position of initial corrosion and influence of crack on the reinforcing bar corrosion are studied in this paper both the flexural bearing capacity performance and the material mechanical performance of the beams are studied on the test of full scale concrete beam a model of 3d fem is established to simulate the state of the actual full - sized rc beam and electronic accelerating test beams, computational results and test results are compared

    通過對混凝土梁的干濕循環試驗,研究了在混凝土梁中的鋼筋初始銹蝕情況,以及不同寬度的裂縫對于鋼筋初始銹蝕的影響。通過對足尺銹蝕混凝土梁的試驗,研究了混凝土梁在海洋環境侵蝕作用下的材料性能的變化和抗彎承載能力的變化。
  9. This paper aims at the seriousness of concrete structure crack and presents one of main cause is that concrete early - age ( especially autogenous shrinkage ) become large through the systems academic analysis

    本文正是針對混凝土結構工程早期裂縫的嚴重性,通過理論分析,指出目前混凝土早期收縮(主要自收縮)的變大是造成這種早期裂縫的主要原因之一。
  10. Main achievements of the thesis : through analysis of the reasons of blockwork crack, i put forwards the measures on material production, shop drawing design and construction management, etc. especially, i put forwards to theory that changing traditional painting technics to avoid crack of painting layer. the application of above measures in engineering proved they are effective

    介紹了砌塊在國內外的發展與應用,研究了混凝土裂縫產生的機理,裂縫的形態及裂縫產生的原因,進一步分析研究了砌塊墻體開裂的各種因素,提出了在設計、生產、施工等環節的治理開裂措施。
  11. This paper, based on the finite element method ( fem ) and utilizing two different means, analyzes the stress and strain field distribution of central through crack tip on a finite flat plate, and calculates the stress intensity factor of the crack tip

    摘要基於有限元分析方法,對有限大平板中存在的中心穿透裂紋,分別用不同的方法分析其裂紋尖端應力、應變場分佈,計算出裂紋尖端的應力強度因子。
  12. The fluid molecular clusters near the interface crack to form smaller fluid molecular clusters through collision, and then fall into the aqueous phase. the smaller fluid molecular clusters continue breaking through disturbance, collisions and attraction by the neighboring molecular clusters. the process continues until a single fluid molecule is formed

    溶解不是以單個分子的形式擴散進入水相中,而是相界面的流體分子簇通過碰撞、裂解成小規模分子簇后落入水相,在水相中繼續受周圍分子簇的持續擾動、碰撞和吸引作用解體,最終成為單個流體分子。
  13. The main research is below : ( 1 ) the influence to intensity and rigid with corner angle ( 60, 75 and 90 degree ) of crack and the board axes ( 2 ) do a fem stress / strain and crack growth simulation analysis when the corner angle of crack and the board axes is 60 degree ( 3 ) do a intensity resume analysis for the structure which is repaired with a titanium patch in a mechanical way when the corner angle of crack and the board axes is 60 degree through simulation analysis for three failure criterion, we have : ( 1 ) in 60, damage extend quickly with damage analysis in hashin criterion ; it is slower for analysis in maximum stress or hashin - rotem criterion. ( 2 ) in special term ( physical condition incision, shape or maximum load ) the compression strength of the stiffened plate will decline 45 % ~ 50 % under compression loads

    通過採用三個不同損傷判據的數值模擬模擬,得到如下結論: ( 1 )在60時,用hashin判據進行的損傷分析,損傷擴展較快;最大應力及hashin - rotem判據進行的損傷分析,損傷擴展基本相當,且較慢; ( 2 )在所給加筋板的物理條件、切口大小及形狀、最大載荷等一定的條件下,該加筋板在壓縮載荷作用下,其壓縮強度下降了45 50 ; ( 3 )在本文提及到的機械連接修理方法以及載荷條件下,修理后的結構強度恢復能夠滿足戰時要求。
  14. Field investigations found that epigenetic reworking deformation fracture include 3 types, named normal relief fracture, fracture filled mud and epigenetic reworking of disturbed belts. and epigenetic reworking of rock mass structural also includes gradual deformation of the blocks that are made up of different attitudes structural planes besides normal relief. through field geological investigations, the features of rock mass structural planes are generalized, especially development laws of interlayer shearing belts, instrastratal shearing belts, faults and base crack

    在已有研究成果基礎上,總結了壩區玄武巖的巖相特徵和構造應力場對巖體結構的影響;通過現場調查,總結了3種類型淺表生變形破裂,即正常卸荷型破裂、鬆弛夾泥型破裂和緩傾角錯動帶表生改造;通過野外地質調查,總結了層間錯動帶、層內錯動帶、斷層和基體裂隙的發育規律。
  15. Through adding low viscidity hpmc, workable performance of the dry - mixed mortar can he greatly improved, and this dry - mixed mortar can well solve the crack problem of wall

    通過摻入低粘度的羥丙基甲基纖維素后,砂漿的施工和易性能得到了極大的改善,可以較好地克服新型墻材出現的墻體裂縫等問題。
  16. The main results and academic contributions of the dissertation can be summarized as following : 1 ) for the difficulty to obtain the accurate analytical solution of the stress constraints around 3d cracks, detailed 3d fe analyses have been conducted to study the out - of - plane constraint factor tz around a straight through - thickness crack, a quarter - elliptical corner crack and a semi - elliptical crack embedded in an isotropic elastic plate subjected to uniform remote tension loading. the distributions of tz are minutely studied in the forward section of the cracks. strong 3d zones ( tz > 0 ) along the crack front were investigated despite the far field stress - free boundary conditions

    全文主要研究內容和學術貢獻如下: 1 .針對一般三維裂紋端部場應力約束準確解析的困難,對均勻拉伸載荷作用下各向同性彈性板中穿透厚度中心直裂紋、半橢圓表面裂紋和1 / 4橢圓角裂紋進行了大量詳細的全場應力三維有限元分析,首次全面分析了非穿透裂紋端部場三維影響區范圍,給出了不同形狀三維裂紋前沿離面應力約束因子tz的數值解,並結合k場平面解給出了非穿透裂紋端部應力場k - tz雙參數描述。
  17. From the test results, suggestion that negative moment reinforcement should run through the specimens to postpone the crack ' s appearance and improve the specimens " fire endurance are also proposed

    由此提出了拉通板頂負筋的建議,以延緩橫向貫通裂縫的出現,達到保護預應力筋和提高連續板耐火性能的目的。
  18. And it investigates the appearance condition ( including joint, crack, eroding, corrosion, braking pole device rupture, crane - girder ' s gnawing railway and so on ) of the whole crane - girder system on the spot, at the same time, it also actually examines the stress of the beam, chemical ingredient, distortion and railway excursion, etc. through sampling, and based on the actually examined results, it checks and calculates the carrying capacity of crane - girder system. then, based on the investigating on the spot and the calculated result, it discusses the mechanism of fatigue failure of the upper part of welded steel crane - girder, analyses the reason of steel crane - girder in the high - frequency emerging the fatigue crack, institutes the strengthened method of damaged steel crane - girder of accurate packing up workshop of the primary mill plant. finally, it presents some advice and suggestions for the repairing and strengthening method of fatigue crack of upper part of steel crane - girder in the high - frequency

    針對包鋼初軋廠精整車間鋼吊車樑上部區域出現裂縫這一問題,本文首先綜述了國內外關于焊接鋼吊車樑上部區域疲勞裂縫的研究現狀;其次對整個吊車梁系統的外觀情況(包括連接、裂縫、腐蝕、銹蝕、制動桿件斷裂、吊車啃軌等)進行了現場調查,抽樣實測了梁的應力、化學成分、變形及軌道偏移等,根據實測結果,對吊車梁系統的承載能力進行了驗算;然後,根據現場調查及計算結果,探討了焊接鋼吊車樑上部區域疲勞破壞的機理,分析了重級工作制鋼吊車梁出現疲勞裂縫的原因,制定了初軋廠精整車間破損鋼吊車梁的加固方案;最後就重級工作制鋼吊車樑上部區域出現疲勞裂縫的修復與加固方案提出了一些意見和建議。
  19. Through the experiment research on practical damaged element, considering the effect of durability damage of steel corrosion and crack on structural element function. for the maintainment and transform plans " selection and prevention of heavy accidents the paper put forward abundant basis. it ' s perfection and development will provide basis for scientific management of active structure

    分析可知:鋼筋銹蝕是造成結構承載力下降的根本原因,同時也找出鋼筋混凝土結構耐久性影響的因素,為合理選擇大修改造方案,防止重大事故等方面提供充分依據,它的完善和發展將為現役結構的科學管理提供依據。
  20. Through the improvement to the press craft for the heavy wall - head, avoids the production of its surface crack, guarantees the products ' quality, it offered the reference for the work in the future

    摘要通過對厚壁封頭壓制工藝的改進,避免了其表面裂紋的產生,保證了產品質量,為今後的厚壁封頭壓制工作提供了參考依據。
分享友人