tube plug 中文意思是什麼

tube plug 解釋
管塞子
  • tube : n 1 管，筒；顏料管。2 管狀地下隧道；〈口語〉（倫敦的）地下鐵道。3 【炮】炮身；【汽鍋】鍋管；【解...
  • plug : n 1 塞子；（齲齒等的）填塞物。2 救火龍頭，消防栓；（內燃機的）火花塞；【軍事】火門閂；槍口蓋；【...
  1. It is suitable to be used as the medium to filter the high purity and strong corrosive gas or liquid, the air plug of battery, gasket, seals for medium / low pressure, the waveguide tube pre - heater for boiler, the sealing wash, the cover of big - powered micro - wave antenna, and radar antenna of twt etc

    適用於過濾、高純度、強腐蝕性的氣體液體介質、蓄電池上作氣塞、襯墊、中低壓密封元件、鍋爐波管預熱器、密封圈和軍用微波大功率天線罩，以及行饋網路雷達天線等。
  2. The main products are just like electric heater for freezer, metal heating tube, heating band cable, rv rvv wire and cable series, power cord plug cable, component for thermoatat, temperature sensor etc

    公司現主導產品為家用冰箱電加熱器金屬管電加熱器電熱帶發熱電纜rv rvv系列電線電纜電源線插頭限溫器組件溫度傳感器組件等。
  3. Plug - in unions, tube end. iso thread profile and tolerances

    管端插入式聯管節. iso螺紋牙形和公差
  4. Insert power plug, vacuum tube and connect casing line as per casing sequence

    插上電接插頭、真空管，按缸序接好缸線；
  5. So the foundation is set for its practical use. 4 the acting - straight - sorting and dropping plug set is designed, which can solve the sorting plugs unclearly because of the difference between individual plug seedlings, and can raise the punctuality of sorting plug seedlings and the veracity of plug seedling dropping into the lead - plug - seedling - tube, in addition, the working frequency of acting - straight cylinder is calculated by analysis to the movement and strength of the key parts in this system which can accelerate the transplanting rate to 3 plants per second, further more, a lot of operated experiments indicate that the working reliability of this set can be raised under the condition of the proper seedling transplanting speed

    4採用直動? ?雙擋銷式分缽落苗系統，不僅解決了因為缽苗個體差異帶來的分缽不清的問題，而且提高了缽苗分缽的準時性和缽苗落入導苗管的準確性；同時，通過對該系統工作過程的主要工作參數的運動和受力情況分析，確定了該系統各直動汽缸的工作頻率，使分缽落苗速度達到3株/秒以上，進一步通過大量試驗對其進行驗證，證明了該系統在滿足栽植速度要求的前提下，可以大大提高了系統的工作可靠性。
  6. Abstract : this paper analyzes theoretically the effect of the reversed cone angle and length of the plug on restraint and elimination to the distortion of the internal spiral ribs, and put forth the design methods of the plug in drawing rifled tube

    文摘:從理論上分析了芯棒倒錐角和芯棒長度對內螺旋凸筋形狀畸變的抑制和消除作用，提出了採用倒錐形等螺距芯棒拉拔內螺紋管時芯棒幾何參數的設計方法。
  7. Rech. aircraft fluid installations. plug - in unions, tube end.

    飛機液壓裝置.管端插入接頭
  8. The calculation results show that the stress distributing of the plug drawing tube is different because of different dies, the drawing force and pulling force are lager in arc die and the diameter and wall thickness are closer to the designing value in cone die

    計算結果表明，不同的模具，芯拔管的應力分佈不同，弧形模成型的拔制力與芯棒后拉力較大，錐形模成型后鋼管的直徑與壁厚更接近設計值。
  9. In order to obtain the stress distributing rules of the forming process of short plug drawing tube and the differences of drawing force, pulling force and dimension precision under different dies, fe method was used and fe model of the plug drawing tube under different dies was built

    摘要為了獲得不同的模具下短芯棒拔管成型過程中的應力分佈規律以及不同模具對短芯棒拔管拔制力、芯棒后拉力和尺寸精度的影響規律，利用有限元的方法，建立了不同模具下短芯棒拔管成型的有限元模型。
分享友人
分享到 Line

分享到臉書