void value 中文意思是什麼
void value
解釋
沒有價值-
Research about ctod and its components 8 ", " shows that the direction angle of ctod vector is identical with the fracture angle of void - mode fracture, which is obtained through experiments, and it is also identical with the result got by peak value line of stress triaxiality. besides, 8 i " was compare with vgc as criterion for initiation of void - mode fracture
對裂紋尖端張開位移ctod及其張開型分量~ 1和剪切型分量~ 11的分析表明，在試件發生韌窩型斷裂時，按照圓弧裂紋中ctod矢量的垂直方向預測的斷裂角與試驗測得的斷裂角符合較好，與三軸度脊線預計的結果也比較一致。 -
The research results show that aggregate gradation and the nominal maximum aggregate size evidently influence the shear resistance of asphalt mixture ; aggregate flakiness content influences the shear resistance of asphalt mixture, and with the increase of aggregate flakiness content the shear resistance of asphalt mixture decreases ; asphalt binder properties, especially penetration, softening point and viscosity influence the shear resistance of asphalt mixture, and the latter increases with the decrease of penetration and the increase of softening point and viscosity ; asphalt content influences shear resistance of asphalt mixture, and with the increase of binder / aggregate ratio the shear resistance of asphalt mixture decreases ; air void influences shear resistance of asphalt mixture, and usually with the increase of air void the shear resistance of asphalt mixture decreases ; homogeneity does not have a direct and obvious relationship with absolute value of shear resistance of asphalt mixture, but does with variation of shear resistance of asphalt mixture
研究結果表明：集料級配和公稱最大集料粒徑對瀝青混合料抗剪強度有顯著的影響；瀝青混合料抗剪強度受其集料中針片狀含量的影響較大，集料中針片狀含量增大，瀝青混合料抗剪強度減小；結合料的性質，特別是針入度、軟化點和粘度對瀝青混合料抗剪強度有較大的影響，隨著針入度減小，軟化點和粘度增大，瀝青混合料抗剪強度增大；含油量對瀝青混合料抗剪強度有較大影響，隨著油石比的增大，瀝青混合料抗剪強度減小；瀝青混合料抗剪強度受其空隙率的影響較大，一般隨著空隙率的增大，其抗剪強度減小；瀝青混合料均勻性與瀝青混合料抗剪強度絕對數值間沒有明顯的關聯，而與數值間的變異性有著很好的相關性。 -
The value of pfca was a denotation of properties of the weakest part, viz. interfacial zone between cement paste and aggregates in concrete, the pfca was a function of void structure in interfacial zone
粗集料破碎率的大小是混凝土最薄弱環節? ?漿體與集料界面? ?性能的一個表徵，它是界面孔結構的函數。 -
Both accessors return void, so any return statement must not return a value
兩個訪問器都返回void ，因此所有返回語句都不能返回值。 -
If asphalt concrete specimen is in stabilization by exert confining stress before the static triaxial test, it is then found that under the condition that time is long enough, the volume of the specimen will shorten gradually and stable around a fixed value, and the amount of compression is essentially the half of the volume of void itself. it is also found that in stabilization by exert confining stress the linear phrase will be shorten in the figure of the static triaxial test of specimen, while the initial tangent modulus will be augment. 3
在進行靜三軸試驗以前先對瀝青混凝土試件進行圍壓穩定，發現在時間足夠長的條件下，試件的體積會逐漸縮小，並逐漸穩定在某一定值，其壓縮量基本上為其本身孔隙體積的一半；經圍壓穩定后的試件靜三軸試驗曲線上的線性階段明顯縮短，而初始切線模量增大。 -
In short, the analysis of arc - tip fracture shows that : the initiation of void - mode fracture can be judged by vgc criterion, or by j ". according to sx criterion ; fracture direction of void - mode fracture can be determined by ctod and peak value line of stress triaxiality. the mesomechanics mechanism of shear - mode fracture need further study, and analysis found direction of plastic belt is consistent with the direction of shear - mode fracture
綜上所述，本文通過對圓弧尖端裂紋的分析表明：對于韌窩型斷裂的起裂，可以依據-復合型斷裂的sx準則按照i ~ 1來預測起裂載荷，也可用v _ （ gc ）判據來預測起裂載荷，二者結果相近；對于韌窩型斷裂的斷裂角，用ctod矢量方向和三軸度脊線方向判斷均和試驗結果基本。 -
The result shows that the value of void fraction is reliable and can reflect the real status. in this paper the error source is analyzed and discussed and the approach of how to advance measure precision is proposed, which has significant fact meaning
文中還對採用圖像處理計算摻氣濃度過程中出現的誤差可能來源及提高測量精度的途徑進行了分析和探討，這對于提高摻氣濃度的計算精度具有重要意義。 -
If the void pointer is non - null, pthread join will place our thread s void return value at the location we specify
有時具有值，而有時當作0 ，這取決于環境。在這種情況中（而且
分享友人