width basis 中文意思是什麼
width basis
解釋
路寬分級標準-
The approximation analysis result of band dipole model is obtained on the basis of the theory of mfl. the electromagnetic distribution feature of the defect in the steel panel is studied by means of simulation. the leakage magnetic distribution of the two defects and four defects plural and the defects in the column differently in the width are also assayed. conclusions that factors affecting flaw magnetic leakage to the panel also affect the column and magnetic leakage bx should be the feature of the flaw identification to several flaws are drawn
在對漏磁檢測原理進行詳細介紹的基礎上，得出了帶偶極子模型的近似解析解，並以有限元數值模擬分析為主要手段，以鋼板上缺陷為對象，分析了各因素對缺陷漏磁場產生影響的不同規律，同時模擬分析了板上平行的兩條裂紋，四條裂紋以及柱體上寬度不同時的裂紋的漏磁場分佈特徵，得出結論:影響板上缺陷漏磁場的諸因素會對柱體上缺陷漏磁場產生同樣的影響;對于多條裂紋，宜用漏磁分量bx作為缺陷識別的特徵量。 -
On the basis of the analysis and compare, we designed the least length of s - bend y - branch to decrease the transmission loss when the space between the outport is 250jjm. we also analyzed thoroughly dependence of half - wave voltage and bandwidth on the width, the length of modulator ' s electrodes and the gap between two electrodes
對于調制器的電極本文也進行較為深入的研究，探討了電極寬度、電極長度、電極間距對半波電壓的影響，並據此對單y相位調制器的電極結構進行了優化設計。 -
This article puts forward a solution named divide - assemble by deducing the size of bp neural network to overcome entering the local best point, the dividing process is that a big bp neural network is divided into several small bp neural networks, every small bp neural network can study alone, after all small bp neural networks finish their study, we can assemble all these small bp neural networks into the quondam big bp neural networks ; on the basis of divide - assemble solution, this article discusses the preprocessing of input species and how to deduce the size of bp neural network further to make it easy to overcome entering the local best point ; for the study of every small bp neural network, this article adopts a solution named gdr - ga algorithm, which includes two algorithms. gdr ? a algorithm makes the merits of the two algorithms makeup each other to increase searching speed. finally, this article discusses the processing of atm band - width distribution dynamically
本文從bp網的結構出發，以減小bp神經網路的規模為手段來克服陷入局部極小點，提出了bp神經網路的拆分組裝方法，即將一個大的bp網有機地拆分為幾個小的子bp網，每個子網的權值單獨訓練，訓練好以後，再將每個子網的單元和權值有機地組裝成原先的bp網，從理論和實驗上證明了該方法在解決局部極小值這一問題時是有效的；在拆分組裝方法基礎上，本文詳細闡述了輸入樣本的預處理過程，更進一步地減小了bp網路的規模，使子網的學習更加容易了；對于子網的學習，本文採用了最速梯度? ?遺傳混合演算法（即gdr ? ? ga演算法） ，使gdr演算法和ga演算法的優點互為補充，提高了收斂速度；最後本文闡述了用以上方法進行atm帶寬動態分配的過程。 -
On the basis of this, the paper makes a great deal of calculation and analysis in this part, different parameters " effect and stress gradient are included. local buckling coefficient and the efficient width calculated formula are provided and look forward to take a reference to the redaction of the specification
本文對此內容進行了較為深入的研究，考慮了多個參數的影響，對各種應力比作用下的楔形腹板的屈曲及屈曲后強度進行了計算分析，得出了考慮翼緣相關作用的楔形腹板屈曲系數及有效寬度系數的計算公式，以期為規范的修訂提供參考。 -
On the basis of analyzing the actual way of classification of unloading zones, the author puts forward a divisiory way of adopting joint rate, opening joint rate and summation of joint width as quantitative indexes according to formation mechanism and geological exhibition of unloading zones
在分析目前卸荷帶劃分方法的基礎上，根據卸荷帶的形成機理及地質表現，提出了用裂隙率、張開裂隙率和「隙寬和」 3個量化指標進行卸荷帶的劃分。 -
This paper ' s study is focused on the principle of bistatic sar on the basis of giving a brief introduction of sar principle, including azimuth resolution, mapping width, focusing deepness, pulse repetition frequency limitation and radar equation etc. then the paper studies the special form of bistatic sar with stationary transmitter
在簡要介紹了合成孔徑雷達的成像原理后，本文著重從原理方面對雙站sar進行了分析，討論雙站sar的方位向解析度，測繪帶寬，聚焦深度，脈沖重復頻率限制，雷達方程等問題，然後對發射機固定的雙站sar這種特殊的雙站sar模式進行分析。 -
On the basis of a lot of experimental data based on the orthogonal test of pulse peak electric current, pulse width and pulse intermission, experimental mathematical models of electric spark forming of several sorts of materials are built up with multiple linear regression analysis
摘要用正交試驗法對電火花加工中的峰值電流、脈沖寬度、脈沖間隔進行設計，在大量實驗數據的基礎上，採用最小二乘法建立實用的多種材料的電火花加工實驗數學模型。 -
Based on the analysis of the stress distribution law in different districts around the self - closed and full - connected arch walling support roadway, the relationship among the limit equilibrium radius and the in - situ rock stress, the physico - mechanical properties and support parameters is obtained. the calculation formula of arch walling width design is put forward so as to provide a theoretical basis for the practical design of support
在分析自封閉全接觸碹體支護巷硐周圍不同區域應力分佈規律的基礎上，得出了圍巖極限平衡區半徑同巷硐所處的原巖應力，圍巖本身的物理力學性質及碹體支護參數間的相互關系，提出了設計碹體厚度的計算公式，為實際進行支護設計提供了理論依據。 -
On the basis of the research on the channel transit capacity of single vessel, and with the combination of previous research methods, a comprehensive assessment model is set up in view of the effective width of the channel ; the passing depth of the channel ; the time taken for passing at high tide. some new viewpoint are developed from the mathematical analysis on the width of the track belt
針對基於單船的航道通過能力的研究，結合以往研究方法，確定了以航道有效寬度、航道通航水深及乘潮歷時為考察對象的綜合評定模型，針對將數學方法結合數值模擬對航跡帶寬度的求解提出了一些新的見解。 -
For the laminate which contains a crack, the suggested patch shape is rectangle, the patch thickness is equal to the parent laminate and the patch stacking sequence is the same as the parent laminate. because the length and the width of the patch have the fewer influence on the repair effect, the patch has the least weight on the basis of enough edge distance, end distance and space having been promised
?對于含裂紋復合材料層壓板，長方形補片的長度和寬度對修補效果沒有非常明顯的影響，因此在保證連接邊距、間距和端距的條件下，補片大小的選擇應該以節省重量為原則；而當補片的鋪排順序與母板相同、相對厚度為100時能夠獲得比較好的修補效果。 -
We encoded and optimized the filter to design the algorithm for filter. computer simulation of complete simulation has demonstrated that the new filtering technique can significantly not only reduce the width relative deviation and the area relative deviation of the image, but also improve the resolution and the focal depth. it provides directive basis for the development of the experiment and the practicability of the technology
計算機模擬結果表明，通過在非瞳孔面的適當分數傅立葉變換面上加入優化設計的位相型濾波器，可有效減小光刻圖形的線寬偏差和面積偏差，提高成像系統的解析度和焦深，為分數域濾波改善光刻圖形質量實驗的開展和這一解析度增強技術走向實用化提供了指導依據。 -
On the basis of the above, integrating with the practical facts about the test for width and thickness of stripe in the in - wall of cylinder after laser thermal treatment, it is proved that the feasibility of eddy - current test technology applied in the lest for width and thickness of stripe in the in - wall of cylinder after laser thermal treatment
在此基礎上，結合汽缸內壁激光熱處理條紋厚度和寬度檢測的實際情況，證明了電渦流多頻率多參數檢測技術在汽缸內壁激光熱處理條紋厚度和寬度檢測中的可行性。 -
Besides, the motor control system based on the digital signal processor ( dsp ) is analyzed. the hardware circuit about the dsp system is designed. the dsp control software is programmed on the field magnetic orientated control and the space vector pulse width modulation ( svpwm ), that establishes the ' basis for implementing the modern control principle
然後，又對基於數字信號處理器（ dsp ）的電機控制系統進行了分析，設計了dsp系統的硬體電路，並編寫和調試了空間磁場定向控制和空間矢量脈寬調制（ svpwm ）的dsp系統的軟體，為直線電機現代控制策略的具體實現奠定了基礎，並提出了對端部效應進行補償的控制方法。 -
In order to accelerate the development of preflex composite beam in railway bridges and to design and construct preflex composite beam bridges of railway in our country reasonably, this thesis is from the scientific project of railway department " experiment and application research of railway preflex composite beam " and summarizes the design information and practical projects on preflex composite beam. on the basis of above works, this thesis improves computation method in analysis of railway preflex composite beam on sectional stress, deflection of mid - span, crack width and shearing resistance and programs a software " preflex composite beam bridge structure analysis system - pfsas ", which is adapt to railway bridges in our country. moreover it makes a primary research in construction techniques and structure measures
為了迅速促進預彎組合梁在我國鐵路橋梁中的發展，合理地進行我國鐵路預彎組合梁橋的設計和施工，本文結合鐵道部科技研究開發項目「鐵路預彎組合梁的實驗與應用研究」 ，在總結以往對預彎組合梁力學性能研究成果及實際工程的基礎上，完善了鐵路預彎組合梁的截面應力、跨中撓度、裂縫寬度和抗剪分析的計算方法；編制了適用於我國鐵路橋梁的「預彎組合梁橋結構分析系統? ? pfsas 」軟體；並對預彎組合梁的施工工藝及構造措施進行了初步探索。 -
On the basis of combining depth with width, macro analysis with microanalysis, theory with reality, and quantitative analysis with qualitative analysis, this article analyses deeply the characteristics, mechanism and evolving trend of the marine industry structure in zhoushan. some adjusting methods and strategies are herein put forward. the whole article is divided into five parts
本文試著從廣度和深度、宏觀和微觀、理論和實際有機結合的基礎上，本著定性與定量相結合的原則，深入分析舟山市海洋產業結構特徵及形成機制，探討和研究舟山市海洋產業結構的演進趨勢，並提出舟山市海洋產業結構調整的戰略與對策，全文共分五部分。 -
Firstly it constructed a curved face equation, and then did self - learning by adjusting power gene and center and width of the radial basis function with restriction condition on reflect function, finally gained satisfactory curved face equation
該演算法先採用網路構造一個曲面方程，再利用反射函數作為約束條件，通過調整權因子和徑向基函數中心和寬度對網路進行自學習，得到一個滿意的曲面方程。 -
Using the optimal neural network, the optimal performance and - hi - the best configuration can be maintained in the training. therefore the configuration of network is unchanged when the width is changing. in other words, it realizes the intelligence of the shape signal ' s pattern recognition and brings out basis for the establishment of shape control scheme
目的在於使該網路性能在訓練中始終保持最優，始終達到最佳結構，有效解決了板寬變化時神經網路結構形式不變的問題，從而實現了板形信號模式識別的智能化，為板形控制策略的制定提供依據。 -
In this article, the writer put forwards his new opinions about the distribution channel designing. he tries to find the solving way of the distribution channel in yinmore on the basis of studying channel length, channel width, two - winner cooperation, channel depth and value chain. at last the writer hope that this paper can be used in the other medical enterprises for references
在本文中，筆者在分銷通路設計原則分析上有自己的觀點，試圖通過分銷通路的研究方法? ?通路長度、通路寬度，雙贏合作關系、深度分銷和價值鏈的運用，為英茂藥業公司的分銷通路謀求較適當的解決辦法，也為藥品分銷通路轉型期間的醫藥企業提供借鑒。 -
At the same time, a series of development trend in organization structure innovation under the information environment has been put forward : flat model is the basis of organization structure optimization ; flexibility not only is beneficial to organization creation, innovation and accelerating reaction speed, but also strengthens organization ' s control centripetal force during the process of being operated continuously. it has rapid adjusting ability in time according to unexpected results of predictable change ; networking can not only decrease internal management cost and realize integration between supply chain and sale chain in worldwide, but also realize enterprise " s completely authorized managemen in order to promote substantial leap in enterprise economic benefit ; virtual model is centralizing limited resources on high additional value function and making low additional value virtual in order that the largest resource support can be obtained in the lowest cost and the whole organization is operated in the most effective way for adapting to market " s rapid change with high elasticity ; creating learning pattern in organization makes enterprise expand the width and depth of information being exchanged with the outer so as to keep enterprise in an unassailable position
提出信息化環境下組織結構創新的一系列發展趨勢：扁平化是組織結構優化的基礎；柔性化既有利於組織的創造、革新、加快反應速度，又能使組織在不斷磨合中加強控制的向心力，具有適時根據可預期的變化的意外結果迅速調整的能力；網路化不僅減少了內部管理成本、實現了企業全世界范圍內供應鏈與銷售環節的整合，而且實現了企業充分授權式的管理，極大地促進了企業經濟效益，實現質的飛躍；虛擬化是將有限的資源集中在附加值高的功能上，而將附加值低的功能虛擬化，以最小的代價獲得最大的資源支持，從而使整個組織以最有效的方式運轉，以高彈性化來適應市場的快速變化；創建學習型組織，使企業拓展了與外界進行信息交流的廣度和深度，使企業立於不敗之地。 -
This paper conducts simulation experimental research on channel navigation area using large - scale ships operation simulator, including the ships ' danger under different wind, wave and flow conditions and safety appraisal result, time needed for entering and leaving port, and recommends the reasonable width of waterway, so as to provide reliable basis for engineering structural design and working - out of ships - operation regulations
摘要利用大型船舶操縱模擬器對航道航行水域進行模擬試驗研究，包括不同風、浪、流等環境下操船危險度及安全評價結果，進、出港所需時間，並推薦航道的合理寬度，為工程結構設計和操船規程的制定提供可靠依據。
分享友人