yield point strength 中文意思是什麼

yield point strength 解釋
屈服點強度
  • yield : vt 1 生出，產生（作物、報酬、利益等）。2 給與，讓與；讓渡；放棄（權利、地位等）；交出。3 承認。4 ...
  • point : n 1 尖頭，尖端；尖頭器具；〈美國〉筆尖；接種針，雕刻針，編織針；小岬，小地角；【拳擊】下巴。2 【...
  • strength : n. 1. 力，力量，體力。2. 強度，濃度；長處；（要塞等的）抵抗力。3. 實力；兵力；全體人數，額定人數，編制。4. 筆力；文勢。5. （證券等的）市價堅挺。6. 〈美俚〉（可能有的）利潤。
  1. Yield strength yield point of steel

    鋼材鋼筋屈服強度屈服點
  2. Through the strong pulling tests of four kinds of synthetic fiber filter cloth, the mechanical performance index of the filter cloth in dry and wet conditions were measured, the influence of various pulling speeds on the fracture strength and the fracture tensile rate of the filter cloth was derived. it was concluded that the stress of the filter cloth could relax when it was beyond the yield point

    通過4種合成纖維濾布的強力拉伸試驗，測得了濾布在干、濕兩種狀態下的力學性能指標，得出了不同拉伸速度對濾布斷裂強度和斷裂伸長率的影響，同時指出當濾布的應力超過屈服點時，會出現應力松馳現象。
  3. The results are follows : chemical composition, tensile strength, yield strength and elongation accord with standard, part corrosion of outside is dew point corrosion, equable corrosion of inside is brought by deoxidized water

    結果表明：其化學成份、抗拉強度、屈服強度、延伸率均符合標準要求，管材外表面局部腐蝕是因露點腐蝕造成，管材內表面受除氧水的作用均勻腐蝕。
  4. Although cold - formed rectangular tube - steel column is favorable to industrialization of mass production, the cold forming process increase the yield point and tensile strength, at the same time the cold forming process decrease the ductile behavior, so it ’ s necessary to research the seismic behavior of cold - formed rectangular tube - steel column for architecture structure

    冷彎矩形鋼管雖然可以實現大批量工廠化生產，但冷彎矩形鋼管在冷成型過程提高了材料的屈服點和抗拉強度同時降低了延性，因而冷彎矩形鋼管作為柱材在建築結構抗震中的應用有待進一步研究。
  5. In terms of strength and ductility, the concept of specified yield point is put forward. based on the principle that under the same condition ( that is, the size of cross section, material strength and reinforcement ratio are identical ), the resultant ultimate moment must be identical, the compression failure of frp reinforced concrete beam is equal to the tension failure for the viewpoint of design and calculation

    從強度與延性兩方面的綜合考慮，提出了纖維增強塑料筋名義屈服點的概念，對發生受壓破壞的纖維增強塑料筋混凝土梁，按照同樣條件下（截面尺寸、材料強度、截面配筋率等均相同）截面承載力相等的原則等效轉化為受拉破壞進行設計與計算，以此確定纖維增強塑料筋的強度折減系數_ f 。
  6. 434 we shall take the sample to test its physical properties ( mechanical properties, tensile strength, yield point, percentage elongation, reduction of area, impact value, brinell hardness )

    我們將取樣試驗其物理性能（機械性能、抗張強度、屈服點、延伸率、斷面收縮率、沖擊值、布氏硬度） 。
分享友人
分享到 Line

分享到臉書