共軸傳動 的英文怎麼說

中文拼音 [gòngzhóuzhuàndòng]
共軸傳動 英文
coaxial drive
  • 共 : 共動詞[書面語]1. （圍繞） surround2. （兩手合圍） span with the hand
  • 軸 : 軸Ⅰ名詞1. （圓柱形的零件） axle; shaft 2. （對稱部分的直線） axis 3. （圓柱形的纏繞器物） roller; spool Ⅱ量詞（用於纏在軸上的線以及裝裱帶軸子的字畫）
  • 傳 : 傳名詞1 （解釋經文的著作） commentaries on classics 2 （傳記） biography 3 （敘述歷史故事的作品）...
  1. So far, the main frame of the conjugation of betrand are established, on the basis of which, it is given that the primary condition the directrix line must be satisfied, the relative curvature of the conjugating surfaces, the relations between non - interventional condition and curvature axle of the directrix line, and so on. the transmission of normal circular - arc gear is a typical bertrand conjugation. in order to promote the transformation from theory to technology, the general principle of this kind of transmission is studied

    為了使研究更加貼近於工程，便於解析處理，提出準面的概念，並確立由準面到準線的研究路線，給出了各種傳動形式下準面與準線的具體特徵，證明了共軛準面上兩準線的誘導測地曲率等於零的這一不干涉條件，進而指出，當準面為平行軸和相交軸傳動的節曲面時，不干涉條件自然滿足。
  2. Iso commercial vehicles and buses - cross - tooth propeller shaft flanges, type t iso 12667 : 1993

    商用車輛和公共汽車. t型交叉嚙合萬向傳動軸法蘭
  3. Specification for components for commercial vehicles and buses - cross - tooth propeller shaft flanges, type t

    商用車輛和公共汽車用部件規范. t型嚙合傳動軸法蘭
  4. It is engaged in developing and producing the transmission parts, such as accurate gear wheel, axles, etc. the company has international advanced technology, and it has been developing over 20 new products, the following three products : motor startup gear, swing bearing and holing rack are the new high - tech product of jiangsu province

    該公司為集團公司與海外留學歸國人員共同創辦的一家高新技術企業，致力於汽車用精密輪軸類等傳動產品的開發鍛造生產，技術水平達到國際先進水平。企業現已完成新品開發20餘項，其中自主開發的汽車啟動電機輪汽車電機啟動器用保持架電錘用擺桿軸承球頭短軸等三隻產品被認定為江蘇省高新技術產品。
  5. The design methods, such as the theory of mechanism dynamic design, the finite element method and the theory of fuzzy reliability etc, are introduced to study the vibration and structural parameters optimization design of the swing movable teeth drive system. the dissertation includes the following six aspects : a ), the torsional vibration dynamic model of swing movable teeth transmission system ; b ). the torsional and flexural vibrations dynamic analyzing model of swing movable teeth drive ; c )

    研究的內容包括以下六個方面： a ）擺動活齒減速器傳動系統扭轉振動的動力學建模； b ）擺動活齒減速器傳動系統彎、扭耦合振動的動力學分析建模； c ）擺動活齒減速器箱體振動的有限元模態分析； d ）擺動活齒減速器高速軸的抗共振模糊可靠性設計； e ）結構參數對活齒傳動嚙合剛度的影響； f ）擺動活齒傳動的模糊可靠性優化設計。
  6. After considering the coupling of the mounting errors and elastic deformation, the meshing influences of the error of the center distance, the setting parametric error in the axial direction, and the intersect angle between the two axes on transmission performance are investigated. 4

    考慮到安裝誤差和載荷作用下的彈性變形等非共軛因素耦合作用，分析了漸開線蝸桿傳動在安裝時存在中心距誤差，軸間相對位置誤差，軸間相對夾角誤差對其承載嚙合的影響； 4
  7. The research and the application shows that the resonator geometrical parameter has effect on its resonant frequency, and the one dimension ( 1 - d ) model can predict the frequency accurately. therefore, if an engine intake noise spectrum is known, one can design a helmholtz resonant silencer to control the intake noise

    一維軸向傳播理論能夠準確預測共振腔的共振頻率，從而為正確設計出針對發動機進氣噪聲頻率特性的helmholtz共振型進氣消聲器提供依據，達到有效控制發動機進氣噪聲的目的。
  8. This paper introduces some traditional and modern methods for the diagnosis of rolling bearings ' faults, which include the shock pulse method, the demodulated resonance method and the wavelet analysis method, etc., and forecasts the developing trends of the diagnosis of rolling bearings ' faults

    介紹了滾動軸承故障診斷的傳統方法和現代方法，如沖擊脈沖法、共振調解法、小波分析法等，預測了滾動軸承故障診斷的發展趨勢。
分享友人
分享到 Line

分享到臉書