嚙合端 的英文怎麼說

中文拼音 [niègěduān]
嚙合端 英文
end of engagement
  • 嚙 : 動詞[書面語]1. （鼠、兔等用牙啃或咬） gnaw （at） 2. （侵蝕） erode
  • 合 : 合量詞（容量單位） ge, a unit of dry measure for grain （=1 decilitre）
  • 端 : Ⅰ名詞1 （東西的頭） end; extremity 2 （事情的開頭） beginning 3 （門類; 方面） item; point 4 （原...
  1. Gear a, at the end of the drive shaft, and gear b, on the countershaft, are in constant mesh

    齒輪a位於驅動軸的末端，齒輪b在副傳動軸上，它們恆定嚙合。
  2. ( 3 ) in the condition of invariable instantaneous speed ratio, the equations of teeth surface of all key components, such as end face gear, oscillating teeth, wave producer, et al, are deduced

    （ 3 ）在保證瞬時傳動比恆定的條件下，由空間嚙合原理出發，重點推導了活齒端面諧波齒輪傳動裝置的主要傳動部件? ?端面齒輪、活齒以及波發生器端面凸輪的齒面方程。
  3. As both the meshing point and ball ' s center are on the given cylinder, a general method for developing the cam ' s profile is studied. it is proved that the profile of positive and negative transmission is unique if the face gear, the difference between face tooth number and ball number and the diameter of ball are the same. the concrete expression of meshing cam on given spatial cycloid profile, and the characteristics of the profiles are discussed

    論文的主要工作包括： 1 、根據嚙合點和鋼球中心軌跡均在同一圓柱面上的特點，研究了給定端齒齒廓條件下求解凸輪齒廓的一般方法；論證了在給定端齒、齒差數和鋼球直徑相同的條件下，正負齒差嚙合齒廓的唯一性；討論了端齒為球面擺線時，凸輪齒廓的具體表達式，並研究了該齒廓的性質。
  4. Cad for meshing analysis of plate harmonic drive

    計算機輔助端面諧波齒輪傳動的嚙合分析
  5. Based on conjunction theory, the models for gear manufacturing is developed, and the equation of the gear surface is gained by the equation of rack cutter. the contact line in manufacturing and the tooth profile of the gear is also discussed based on the equation of the gear surface

    本文首先基於齒輪嚙合原理，建立了齒輪加工的模型，由刀具曲面方程推導出被加工齒輪的齒面方程，並進一步推導出齒輪端截面的齒廓方程和齒輪刀具接觸線方程。
  6. This series of products also claim that " m " was connected, it clenched the teeth after adopting the end tooth, the whorl is joined, it suitable radio communication, cellular telephone and office land network make electric signal transmit and join radio frequency cable spend among a small circle

    該系列產品亦稱「 m 」接頭，它採用了端齒嚙合，螺紋連接，它適用無線電通訊、移動電話及小范圍局域網路作電信號傳輸連接射頻電纜之用。
  7. Rod ends, adjustable, self - aligning plain bearing with self - lubricating liner and threaded shank with engagement : 1. 5 thread - dimensions and loads

    帶自潤滑套和嚙合量為1 . 5的螺紋軸的可動調自定位滾動軸承桿端.尺寸和負載
  8. Rod ends, adjustable, single fork and threaded shank with engagement : 1. 5 thread diameter - dimensions and loads

    嚙合量為1 . 5螺紋直徑的單叉螺紋柄可調節的連桿端頭.尺寸和負荷
  9. Rod ends, adjustable, double fork and threaded shank with engagement : 1. 5 thread diameter - dimensions and loads

    嚙合量為1 . 5螺紋直徑的雙叉螺紋柄可調節的連桿端頭.尺寸和負荷
  10. The result indicates that the two - terminal bracing structure is optimum for bearing load and gear mesh

    計算結果表明：主動齒輪軸兩端支撐結構對軸承受力和齒輪嚙合最有利。
  11. This paper researches a new type mechanical transmission mechanism - end face engagement cycloid steel ball planetary transmission

    本文研究了一種新型行星傳動? ?端面嚙合擺線鋼球行星傳動。
分享友人
分享到 Line

分享到臉書