嚙合方式 的英文怎麼說

中文拼音 [niègěfāngshì]
嚙合方式 英文
engagement system
  • 嚙 : 動詞[書面語]1. （鼠、兔等用牙啃或咬） gnaw （at） 2. （侵蝕） erode
  • 合 : 合量詞（容量單位） ge, a unit of dry measure for grain （=1 decilitre）
  • 方 : Ⅰ名詞1 （方形; 方體） square 2 [數學] （乘方） involution; power 3 （方向） direction 4 （方面） ...
  • 式 : 名詞1 （樣式） type; style 2 （格式） pattern; form 3 （儀式; 典禮） ceremony; ritual 4 （自然科...
  • 方式 : way; fashion; pattern
  1. The paper studies the surface geometry of globoidal indexing cam by applying the theory of conjugate surfaces and the method of coordinate transformation, presents the equations related to the main inducement curvature of the cam profiles, analysis and deduces the equations of two circumscription curves, which judge if the conjugate surface could mesh properly. some calculate examples and conclusion are given. the surface equation of the globoidal cam and conjugate equation are established

    論文首先在分析空間嚙合原理基礎上，採用坐標變換法推導出弧面分度凸輪的工作廓面方程、嚙合方程和壓力角計算公式，對弧面分度凸輪的嚙合特性進行了深入的分析和研究，對判斷曲面能否正確嚙合的依據如兩類界限線方程以及誘導主曲率等進行推導，並給出算例。
  2. As a new type gear transmission, double circular arc profile bevel gearing carries out its transmission by means of meshing between convex - concave tooth profile in both of the direction of tooth trace and the direction of tooth depth, so it has advantage of high load capacity, long service life, easy forming hydrodynamic oil film between teeth as well as high quality of running - in etc. therefore, more attention has been paid to its application and research in recent years

    作為一種新型齒輪傳動方式，雙圓弧弧齒錐齒輪傳動不論在齒線方向、還是在齒高方向，均為凸、凹齒廓相嚙合，因而它比一般的弧齒錐齒輪傳動的承載能力高，使用壽命長；並且在嚙合過程中兩齒面間容易形成潤滑油膜，具有良好的跑合性能，所以對它的應用和研究日益受到人們的重視。
  3. Solid model of the involute worm gearing solid model with drive ratio 1 / 50 is built by using ideas - 5. 0, then the elastic contact analysis is proceeded on the basis of contact fem. the dynamic evolution image of the area of the contact zone, the load sharing among instantaneous meshing tooth pairs, the distribution of the contact force, and tooth stress are obtained. 3

    通過漸開線圓柱蝸桿、蝸輪的齒面方程式，利用ideas - 5 . 0軟體建立了傳動比為1 / 50的漸開線圓柱蝸桿傳動的實體幾何模型，在此基礎上應用接觸有限元方法對該傳動進行了彈性接觸分析，包括接觸區的形狀、位置、載荷在瞬時嚙合齒對的分配狀況； 3
  4. As both the meshing point and ball ' s center are on the given cylinder, a general method for developing the cam ' s profile is studied. it is proved that the profile of positive and negative transmission is unique if the face gear, the difference between face tooth number and ball number and the diameter of ball are the same. the concrete expression of meshing cam on given spatial cycloid profile, and the characteristics of the profiles are discussed

    論文的主要工作包括： 1 、根據嚙合點和鋼球中心軌跡均在同一圓柱面上的特點，研究了給定端齒齒廓條件下求解凸輪齒廓的一般方法；論證了在給定端齒、齒差數和鋼球直徑相同的條件下，正負齒差嚙合齒廓的唯一性；討論了端齒為球面擺線時，凸輪齒廓的具體表達式，並研究了該齒廓的性質。
  5. Creative points and all tasks having be finished are briefly shown below : according to the classical space meshing theory, we have strictly deduced a series of formulae such as the equation of contacting line of worm, the equation of the second limiting curve of worm gear, and the equation of working surface and non - working surface, etc. and we have deeply studied the algorism of the actual contacting lines of worm gear drive

    本文的主要創新點和成果如下：基於經典共軛嚙合理論，對平面二包蝸桿副的運動關系進行了嚴密分析，獲得了蝸桿副齒面方程、蝸桿齒面一界曲線方程、蝸輪齒面二界曲線方程等一系列齒面分析所必須的數學公式，並深入研究了蝸桿副齒面接觸線的演算法，為蝸桿副的三維數字化造型打下了堅實的數學基礎。
  6. Equations of mesh, shorting contact line, undercutting limit line, meshing limit lines and the existence conditions, angle between the direction of relative speed and the direction of contact line, induced normal curvature about every point on the contact line are established. moreover, the paper also theoretically analyzed the error of the grinded gear surface. on the basis of the theory, the computer program is worked out to automatically produce the contact line and the boundary curves of mesh. analysis of meshing circs under different parameters can be done so that we can gain the best process condition

    首先對漸開面二次包絡理論進行了深入的探討，推導出了兩次嚙合的嚙合方程式、瞬時接觸線方程式、根切界限線方程式、嚙合界限線的方程式及其存在條件，相對運動速度方向與接觸線方向的夾角及接觸線上各點的誘導法曲率；此外，還對磨齒后工件的齒面誤差進行了理論分析；並在理論基礎上編制了相應的計算機程序，自動生成接觸線族及嚙合界限線，對不同參數條件下的嚙合情況進行分析，可以使工藝條件達到最佳狀態；最後研究了磨齒裝置，設計了磨齒機的傳動系統。
  7. Tooth surface equations and contact line equations of the involute worm gearing are established according to its machining methodology. meshing characteristics in rigidity condition are studied. these characters include the inductive normal curvature along the contact line on the worm surface, the first and the second limit lines during the engage of the worm gear, and the influence of the intersect angle between the contact line the relative velocity of the worm and the gear on transmission performance

    根據漸開線圓柱蝸桿傳動的創成方法，建立了漸開線圓柱蝸桿和蝸輪的接觸線方程式、齒面方程式，分析了漸開線圓柱蝸桿傳動的剛性嚙合特性，如蝸桿與蝸輪嚙合時的誘導法曲率、一類界限曲線、二類界限曲線和蝸桿與蝸輪間相對速度方向和接觸線方向的夾角對傳動性能的影響； 2
  8. Through systemic analyzing on spiral helical gear transmission with different basic parameters, the essay found out rules of how can such basic parameters influence spiral helical gear engagement characteristics. so it brings forward the auxiliary assembling mode of adopting one straight gear and one helical gear on condition of little axial angle as well as treasures to ameliorate ill engagement performance on condition of large axial angle, another two jobs of the essay are to clarify the wrong concept that spiral helical gear can only transmit movement but not impetus and to provide a brief and practical method of analyzing contact for gear pairs whose surface equations can be written out directly

    通過對不同基本參數的螺旋齒輪傳動進行系統研究，找出了螺旋齒輪基本參數對其嚙合特性的影響規律，提出小軸交角條件下可採用一直齒輪、一斜齒輪的齒輪副組合方式，給出了大軸交角條件下嚙合性能不良的改進措施。澄清了螺旋齒輪只能傳遞運動不能傳遞動力的誤區，為能夠直接寫出齒面方程的齒輪副進行齒面接觸分析提供了一種簡便、實用的新方法。
  9. The paper describes the feature of double circular arc spiral bevel gears, basing on such gears manufacture theory, the paper depicts how to form the double circular arc spiral bevel gear tooth profile, at the same time, depicts its meshing theory and derives its tooth profile equation. basing on fsh short tooth, the paper derives the tooth depth equation, describes its manufacture technology, makes out this tooth propile single side method regulation calculation card

    本文從弧齒錐齒輪加工原理出發，闡述了雙圓弧弧齒錐齒輪副點嚙合齒面的形成原理，同時還論述了雙圓弧弧齒錐齒輪基本嚙合原理，推導出了具有普遍形式的齒面方程，同時以fsh短齒形為藍本還推導出了雙圓弧弧齒錐齒輪齒厚計算公式，闡述了雙圓弧弧齒錐齒輪的製造工藝，編制了雙圓弧弧齒錐齒輪單邊切削法機床調整計算卡。
  10. When there is no or lesser undercut, we can use the bend stress ' s algorithm of involute gear to calculate approximately the bend stress of gear with meshed medium belt, what we to do is to transit the interrelated shift coefficient to the according radial minus shift coefficient of involute gear, and the error can be controlled in 10 %

    在不產生或少量根切時，可用漸開線徑向變位齒輪的彎曲應力計算方法來近似計算帶式嚙合介質齒輪的彎曲應力，只需將關聯變位系數轉化為相應的漸開線齒輪徑向變位系數即可，其誤差在10 %以內。
  11. Firstly, a simple and practical representing method of the tooth edge tangential vector is applied to replace the traditional differential formula, the simple solving technique of edge contact problem makes the geometric edge contact analysis of the complex curve surface realize. secondly, using numerical searching and mathematical programming method solves the contact directions and loaded contact problem. finally, whole numerical simulation method is provided for loaded tooth contact analysis of high contact ratio spiral bevel gears

    首先以一種簡單實用的輪齒邊緣切矢量的數學表示方法取代了經典的微分表達式，大大簡化了幾何邊緣接觸的求解，使復雜曲面的幾何邊緣接觸分析得以實現；其次又採用數值搜索與數學規劃法求解了邊緣接觸的主方向和承載接觸問題，為高重合度弧齒錐齒輪承載嚙合全過程的數值模擬提供了完整的方法。
  12. It was pointed out that the actual center - line and theoretic meshing line of the paired gears varied in the form of planar motion due to the system vibration, and the actual meshing line was curvilinear

    結果表明，由於系統振動的原因，齒輪副的實際中心線和理論嚙合線是以平面運動方式變化的，實際嚙合線（即嚙合點的軌跡）是一條曲線。
  13. Firstly, the paper introduces the development and application of computer graphics & image technique, discusses the principle and method of cg and digital image processing, such as matrix of the graphic transformation, homogeneous reference frame, sampling and quantization of the image, file format of the image, template operation, etc. secondly the paper introduces the purpose and method of image enhancement processing, explains the each occasion of those methods such as threshold transformation, smoothing processing, sharpening processing, analyzes and contrasts the processing results of object image. thirdly, the paper introduces the method of mathematics morphologic, edge detection and thinning processing, attains character description of image and character dots of the contour. fourthly, the paper processes the coordinate transformation to character dots and basic splines fitting, imports correlative condition to devise meshing line and meshing track

    本文首先介紹了計算機圖形圖像技術的發展與應用情況，對計算機圖形學和數字圖像處理的一些基本理論和方法如圖形變換矩陣、齊次坐標系、圖像采樣和量化、圖像文件格式、模板操作等內容進行了討論：然後對圖像增強處理的目的和方法進行了介紹，對諸如閥值變換、平滑處理、銳化處理等方法的應用場合進行了說明，並對實物圖像的處理結果進行了分析與比較；接下來介紹了數學形態學方法、對增強后的圖像進行邊緣檢測的方法和圖像的特徵描述方法，並獲取輪廓的特徵點：隨后對獲取的特徵點進行坐標變換，並進行b樣條曲線擬合，引入相關條件生成齒輪副的嚙合線及嚙合軌跡：最後引入等值線和區域填充表示方法，並以等值線和區域填充的形式對弧齒錐齒輪嚙合模擬的載荷分佈情況進行了直觀的表示。
  14. From the analysis, the angle between the axes of the annular gear and outer profile of the coupling in its steady mesh was derived, and a general method for determining the angle was obtained by using an equilibrium of the forces and couples exerting on the annular gear, from which the vibrational features of the coupling could be revealed

    得出齒式聯軸器聯接不對中的穩定嚙合時內齒環軸線與外齒環軸線間的空間位置關系，以及用內齒環的力和力偶平衡的方法來求其軸線間夾角的一般方法，並得出了齒式聯軸器聯接不對中故障所具有的一些振動特徵。
  15. This paper deduced the involute gear total tooth profile equations of unsymmetric teeth with double pressure angles, proposed the calculation formulas of coordinates and load angle at the upper and lower points of single and double teeth mesh areas, and programmed the relevant parametric programs

    摘要推導出雙壓力角非對稱漸開線齒輪系統全齒廓方程，以及在單、雙齒嚙合上、下界點處坐標和載荷角的計算公式，編制了相應的參數化程序。
  16. Comparison is made between the three kinds of bearing arrangement modes in bearing life and gear mesh

    從軸承壽命和齒輪嚙合2個方面對3種布置方式進行比較。
  17. Taking the meshing theory of conjugate curved surface as a foundation, utilizing array method of rotation transformation of vector, the meshing equation and contour surface equation of conical cam mechanism with swinging conical roller follower were analyzed and derived, and the calculation formula of pressure angle and synthetic curvature of the mechanism was presented, thus laid a solid theoretical foundation for enhancing the machining accuracy of conical cam, improving its processing method and achieved the integration of cam cad / cam

    摘要以共軛曲面嚙合理論為基礎，運用矢量的旋轉變換矩陣法，分析並推導了圓錐滾子擺動從動件圓錐凸輪機構的嚙合方程和廓面方程，並給出了機構的壓力角和綜合曲率的計算公式，為圓錐凸輪加工精度的提高，改進其加工方法，實現凸輪cad / cam一體化奠定了堅實的理論基礎。
  18. By considering the contact between the teeth and utilizing the face to face contact model with contact element and coulomb friction model, the author have developed a computing method for plastic load of tooth - locked quick actuating pressure vessel based on finite element stress analysis and stress categorization

    摘要通過接觸單元來數值模擬嚙合齒的接觸過程，建立了基於整體有限元分析的齒嚙式快開壓力容器塑性載荷計算方法。
  19. Through analysis the reasons influencing measuring stability have been found out, which are the flexure strain and structure resonance produced by the transmission axle under the function of the gearing - in force of the reduction gear

    雖然與傳統的測量方法一致，但經過理論分析，得出了這種測量方式機械結構影響測量穩定性的原因，即傳動軸受減速器齒輪嚙合力作用?生的彎曲應變和結構諧振對測量精度影響最大。
分享友人
分享到 Line

分享到臉書