嚙合齒數 的英文怎麼說

中文拼音 [niègěchǐshǔ]
嚙合齒數 英文
number of teeth in mate
  • 嚙 : 動詞[書面語]1. （鼠、兔等用牙啃或咬） gnaw （at） 2. （侵蝕） erode
  • 合 : 合量詞（容量單位） ge, a unit of dry measure for grain （=1 decilitre）
  • 齒 : Ⅰ名詞1 （牙; 牙齒） tooth 2 （物體上齒形的部分） a tooth like part of anything 3 [書面語] （年齡...
  • 數 : 數副詞（屢次） frequently; repeatedly
  1. If the coefficient of engagement overlap decreases, the flow aggrandize, trapping volume and the flow pulsating ratio decreases

    隨著齒輪嚙合重合系數的減小，齒輪泵的流量增大，困油容積和流量脈動率減小。
  2. Analyse the tooth geometry of klingelnberg cyclo - palloid spiral bevel gear., according to the relative position and kinematic relation of the cutter heads, virtual crown gear and the processed wheel blank, established the system of coordinates of the gear cutting, dedcuced the tooth face equation of the virtual crown gear, according to relations of the gear cutting and space theory of engagement, deduced the tooth face equation of klingelnberg cyclo - palloid spiral bevel gear, and drawing the three - dimensional graphs of the virutal crown gear and klingelnberg cyclo - palloid spiral bevel gear according to the design and setting parameters

    對克林貝格擺線齒錐齒輪進行齒面幾何分析。根據銑齒加工中刀盤、搖臺和輪坯的相對位置和相對運動關系建立了切齒嚙合坐標系，由矢量的旋轉推導了產形輪齒面方程;根據空間嚙合原理和切齒嚙合關系推導了被加工齒輪的齒面方程;由設計參數和銑齒調整參數計算得到齒面離散數據，繪制了產形輪和擺線齒錐齒輪的三維齒形。
  3. Based on the comprehensive estimating method of the final drive, the analysis method is proposed to focus on analyzing one of the important testing targets ? the meshing states of the spiral bevel gears and differential gears of the final drive when they are working under the imitating conditions

    本文主要對汽車后橋主減速器殼表面的振動信號進行分析。這是在主減速器綜合評價方法的基礎上，針對其中一項重要的試驗參數? ?主減速器齒輪的嚙合狀況，而提出的分析方法。
  4. With regard to the restrains of geometries boundaries of the surface, we have finished the tooth contact analyses ( tca ) and precisely drawn the actual contacting area on the surface. the relations between the total length of the actual contacting lines and the rotating angle of worm gear are also revealed in this dissertation

    為了獲得蝸輪輪齒齒面的準確描述，按共軛理論計算了蝸輪齒面的實際接武漢理工大學博士學位論文觸線，通過考慮蝸輪齒面的實際幾何約束，確定了蝸輪齒面的實際嚙合區，並運用數值方法精確計算了蝸輪齒面的邊界線。
  5. On the condition of “ many - head ” and “ small drive ratio ” ， the plane double enveloping hourglass worm can not settle the problem of undercutting and sharpening simultaneously. it has devoted to a new type hourglass worm _ sphere double enveloping hourglass worm. the coordinate system is established according to the frock. the meshing equation and the tooth equation of worm and gear have been developed and the distribution of contact line on gear tooth is analyzed. to evaluate the meshing quality ， four meshing quality indexes and five original parameters are put forward. through mass programming computing ， the relations between meshing quality and original parameters are derived and depicted by graphs

    考慮到平面二次包絡環面蝸桿傳動在多頭小傳動比條件下根切與齒頂變尖的矛盾很難同時解決且嚙合性能較差，介紹了一種新型環面蝸桿傳動? ?球面二次包絡環面蝸桿傳動.在研究過程中，根據工裝建立了坐標系，根據一二包過程的運動關系推得了嚙合方程和蝸桿與蝸輪的齒面方程，分析了蝸輪齒面上的接觸線分佈.為了評價嚙合性能，提出了4項性能指標和5項原始參數，通過大量編程計算得到了嚙合性能指標與原始參數之間的關系，並以圖表直觀的表示
  6. Established the system of coordinates of roll testing, getting the parameters of equation of tooth face by solving the non - linear equations set ; according to the differential geometry and meshing principle, deduce the curvature parameters of tooth face and tooth profile, and get the parameters of instantaneous contact ellipse. emulate the contact trace and contact area of the working tooth face, and drawing the instantaneous drive ratio error curve

    建立了克林貝格擺線齒錐齒輪嚙合分析的對滾模型，通過對非線性方程組的迭代求解，得到齒面方程的各個參數;由微分幾何和切齒嚙合原理推導了齒面上齒廓和齒線方向的曲率參數，得到了瞬時接觸橢圓的參數。根據設計參數和機床調整參數繪制了工作齒面的接觸軌跡和接觸區圖形，並求得了瞬時傳動比的誤差曲線。
  7. These designing parameters include stiffness of epicyclical bearings, synthetic meshing stiffness of gears, stiffness of supporting bearing of out put shaft, mass of inner rack, meshing angle of gears, distance between inputting shaft and supporting shaft and input speed etc. according to these analyses, the possible way for improving the dynamic function of three - ring transmission may be put forward

    這些設計參數包括：行星軸承剛度、齒輪綜合嚙合剛度、輸出軸支承軸承剛度、內齒板質量、齒輪嚙合角、輸入軸和支承軸間距及輸入轉速等，根據這些分析，可以提出改善三環傳動動態性能的可能途徑。
  8. As both the meshing point and ball ' s center are on the given cylinder, a general method for developing the cam ' s profile is studied. it is proved that the profile of positive and negative transmission is unique if the face gear, the difference between face tooth number and ball number and the diameter of ball are the same. the concrete expression of meshing cam on given spatial cycloid profile, and the characteristics of the profiles are discussed

    論文的主要工作包括： 1 、根據嚙合點和鋼球中心軌跡均在同一圓柱面上的特點，研究了給定端齒齒廓條件下求解凸輪齒廓的一般方法；論證了在給定端齒、齒差數和鋼球直徑相同的條件下，正負齒差嚙合齒廓的唯一性；討論了端齒為球面擺線時，凸輪齒廓的具體表達式，並研究了該齒廓的性質。
  9. A mathematical model for gear shaping was presented for machining of externally meshed non - circular gears with shaping procedure in terms of the positional relationship between the tool ( cutter ) and gear ' s pitch curve

    摘要根據范成法加工外嚙合非圓齒輪時刀具和齒輪節曲線間的位置關系，提出了插齒加工的數學模型。
  10. The researchful results indicate that the flux pulse ration of ordinary helical gear pump without clearance is less than that of the gear pump with clearence under the condition that the main parameters are same, and the flux pulse ration of ordinary helical gear pump is less than that of whole profile meshing helical gear pump

    研究結果表明：在主要參數相同的情況下，普通斜齒齒輪泵無側隙時流量脈動率小於有側隙時的流量脈動率；全齒廓嚙合斜齒輪泵比普通斜齒輪泵的流量脈動略小。
  11. One of tooth profiles of coarse - pitch gear ball hob is analyzed in engagement theory ， the tooth profiles of the internal gear has been derived. by comparing the tooth profile with the tooth profile of the standard internal gear, it is shown that the tooth profile is satisfying

    對大模數內齒輪球形滾刀的一種齒形進行嚙合理論分析，求出滾刀加工出來內齒輪的齒形，然後與標準內齒輪的齒形比較，結果表明：該齒形的滾刀加工的內齒輪能滿足要求。
  12. Creative points and all tasks having be finished are briefly shown below : according to the classical space meshing theory, we have strictly deduced a series of formulae such as the equation of contacting line of worm, the equation of the second limiting curve of worm gear, and the equation of working surface and non - working surface, etc. and we have deeply studied the algorism of the actual contacting lines of worm gear drive

    本文的主要創新點和成果如下：基於經典共軛嚙合理論，對平面二包蝸桿副的運動關系進行了嚴密分析，獲得了蝸桿副齒面方程、蝸桿齒面一界曲線方程、蝸輪齒面二界曲線方程等一系列齒面分析所必須的數學公式，並深入研究了蝸桿副齒面接觸線的演算法，為蝸桿副的三維數字化造型打下了堅實的數學基礎。
  13. The analysis about the central gear ' s mentions impact on the flow pulsation of the five poles of the external meshing gear integral pump

    中心輪齒數對五極外嚙合齒輪復合泵流量脈動的影響分析
  14. The parameters of inner meshed gear pump with external circle - arc and its envelope teeth are optimized by the method of the genetics algorithms

    利用遺傳演算法對外圓弧及其包絡線內嚙合齒輪泵的參數進行優化。
  15. The paper presents and improved structure as well as a fuzzy reliable optimal design method mainly for gear parameters of planet reducer with fewer tooth difference in a certain blow molding system, according to the analysis on fault of the original type

    摘要通過對某一吹塑系統少齒差行星減速器的故障分析，提出了相應的改進措施外，更重要的是對少齒差行星減速器的嚙合參數進行了模糊可靠性優化設計。
  16. When bears enough loading, actual contact tooth number will exceed theoretic contact tooth number, which makes the loading capacity of the gears increased dramatically

    三環傳動在足夠大的載荷作用下，實際嚙合齒數會大於理論嚙合齒數，使得三環減速器中齒輪副的承載能力大大提高。
  17. As external gear pump has the most serious problem of flow pulsation, how to analyze the flow pulsation of gear pump and to optimize the construction parameters of gear pump is especially important for the design and performance improvement of gear pump

    在液壓泵中，以外嚙合齒輪泵的流量脈動最大，因此對齒輪泵流量脈動進行分析，以減小流量脈動為目標，對齒輪泵的結構參數進行優化設計，從而為齒輪泵的設計及齒輪泵性能的提高提供理論基礎。
  18. Aimed to the two deficiencies of three - ring gear transmission, the dissertation will analyze these two aspects. the first, according to the finite element model of gear pair of three - ring gear reducer, the dissertation is aimed to analyze the multi - tooth meshing effect of three - ring gear reducer using finite element method, and the number of teeth contacted simultaneously, their load distribution characteristics and the von mises stress change are gained

    針對三環減速器以上兩點的不足之處，本文將對以下兩方面進行分析:首先，本文以三環減速器齒輪副有限元模型為研究對象，利用有限單元法對三環減速器多齒嚙合效應進行分析，得到三環減速器傳動時的實際接觸齒數、嚙合齒載荷分配以及vonmises應力變化規律。
  19. By considering the contact between the teeth and utilizing the face to face contact model with contact element and coulomb friction model, the author have developed a computing method for plastic load of tooth - locked quick actuating pressure vessel based on finite element stress analysis and stress categorization

    摘要通過接觸單元來數值模擬嚙合齒的接觸過程，建立了基於整體有限元分析的齒嚙式快開壓力容器塑性載荷計算方法。
  20. The main research results are as follows : the friction contact between teeth in the tooth - locked quick closure device is studied, and the simulation is made to the contact conduct between the teeth utilizing the face to face contact model with contact element and coulomb friction model, the whole finite element model of tooth - locked quick closure device is created

    本文主要有以下成果： （ 1 ）對齒嚙式快開裝置中嚙合齒間存在的摩擦接觸現象進行了研究，利用接觸單元法採用面-面接觸模型和庫侖摩擦模型對齒間的接觸行為進行數值模擬，建立了齒嚙式快開裝置的整體有限元模型。
分享友人
分享到 Line

分享到臉書