嚙合齒輪 的英文怎麼說

中文拼音 [niègěchǐlún]
嚙合齒輪 英文
contacting gear
  • 嚙 : 動詞[書面語]1. （鼠、兔等用牙啃或咬） gnaw （at） 2. （侵蝕） erode
  • 合 : 合量詞（容量單位） ge, a unit of dry measure for grain （=1 decilitre）
  • 齒 : Ⅰ名詞1 （牙; 牙齒） tooth 2 （物體上齒形的部分） a tooth like part of anything 3 [書面語] （年齡...
  • 輪 : Ⅰ名1 （輪子） wheel 2 （像輪子的東西） wheel like object; ring; disc 3 （輪船） steamer; steamboa...
  • 齒輪 : gear [rack; toothed] wheel; （toothed） gear; wheel gear
  1. Finally, the three dimensional configurations are imported to 3dmax software. making great use of powerful entity rendering and animating ability in 3dmax software realizes gear - spline mesh, gear - gear mesh and cam - block moving dynamic simulation

    最後，將三維實體傳遞到3dmax中，利用3dmax強大的實體渲染和動畫製作功能，實現了齒輪齒條嚙合、齒輪嚙合和凸輪滑塊運動的動態模擬。
  2. Solid model of the involute worm gearing solid model with drive ratio 1 / 50 is built by using ideas - 5. 0, then the elastic contact analysis is proceeded on the basis of contact fem. the dynamic evolution image of the area of the contact zone, the load sharing among instantaneous meshing tooth pairs, the distribution of the contact force, and tooth stress are obtained. 3

    通過漸開線圓柱蝸桿、蝸輪的齒面方程式，利用ideas - 5 . 0軟體建立了傳動比為1 / 50的漸開線圓柱蝸桿傳動的實體幾何模型，在此基礎上應用接觸有限元方法對該傳動進行了彈性接觸分析，包括接觸區的形狀、位置、載荷在瞬時嚙合齒對的分配狀況； 3
  3. As both the meshing point and ball ' s center are on the given cylinder, a general method for developing the cam ' s profile is studied. it is proved that the profile of positive and negative transmission is unique if the face gear, the difference between face tooth number and ball number and the diameter of ball are the same. the concrete expression of meshing cam on given spatial cycloid profile, and the characteristics of the profiles are discussed

    論文的主要工作包括： 1 、根據嚙合點和鋼球中心軌跡均在同一圓柱面上的特點，研究了給定端齒齒廓條件下求解凸輪齒廓的一般方法；論證了在給定端齒、齒差數和鋼球直徑相同的條件下，正負齒差嚙合齒廓的唯一性；討論了端齒為球面擺線時，凸輪齒廓的具體表達式，並研究了該齒廓的性質。
  4. Development and test of an internal gear pump group used for high temperature, high speed and large flow

    高溫高速大流量內嚙合齒輪泵組的研製及測試
  5. Kinematic analysis of relative slide on surface of meshed gears with system vibration

    基於系統振動的嚙合齒輪齒面上的相對滑動運動分析
  6. The at89c52 serves as the center of the automatic control system ' s hardwaie, it doesn " t extend ram and rod

    動力介面通過變速箱側面檢視窗由中間軸上一常嚙合齒輪實現，技術成型、可靠。
  7. Dqj point - line meshing gear reducers

    Dqj點線嚙合齒輪減速器
  8. Although the flux per revolution of the optimized pumps is a little smaller than that of tatsuno combined pumps, other characteristics, such as fluctuation rate, maximum pressure angle and velocity fluctuation rate etc, are much better. the methods to cut gears are proposed in the theory for the practical produce in the future

    雖然，在體積相等的條件下，優化出來的外圓弧包絡線內嚙合齒輪泵的排量略小於tatsuno組合泵的排量，但其它性能（如：流量脈動率、最大壓力角、速度波動量）都更優。
  9. The paper describes the feature of double circular arc spiral bevel gears, basing on such gears manufacture theory, the paper depicts how to form the double circular arc spiral bevel gear tooth profile, at the same time, depicts its meshing theory and derives its tooth profile equation. basing on fsh short tooth, the paper derives the tooth depth equation, describes its manufacture technology, makes out this tooth propile single side method regulation calculation card

    本文從弧齒錐齒輪加工原理出發，闡述了雙圓弧弧齒錐齒輪副點嚙合齒面的形成原理，同時還論述了雙圓弧弧齒錐齒輪基本嚙合原理，推導出了具有普遍形式的齒面方程，同時以fsh短齒形為藍本還推導出了雙圓弧弧齒錐齒輪齒厚計算公式，闡述了雙圓弧弧齒錐齒輪的製造工藝，編制了雙圓弧弧齒錐齒輪單邊切削法機床調整計算卡。
  10. Toothing of chain wheels for roller chains as specified in din 8187 and din 8188 ; profile dimensions

    按din8187和din8188規定的滾子鏈用鏈輪的嚙合.齒型
  11. Constant mesh gear box

    固定嚙合齒輪變速箱
  12. The analysis about the central gear ' s mentions impact on the flow pulsation of the five poles of the external meshing gear integral pump

    中心輪齒數對五極外嚙合齒輪復合泵流量脈動的影響分析
  13. The parameters of inner meshed gear pump with external circle - arc and its envelope teeth are optimized by the method of the genetics algorithms

    利用遺傳演算法對外圓弧及其包絡線內嚙合齒輪泵的參數進行優化。
  14. A simple strategy for overcoming the difficulties can be developed, with a small input torque load, where one of the meshing gears can be modelled with rigid elements

    為了克服困難，一個簡單的策略能夠被采納，這個策略就是在帶有一個很小的輸入扭矩負載下，在加載的地方其中的一個嚙合齒輪的可以被建成有剛性的元件的模型。
  15. When bears enough loading, actual contact tooth number will exceed theoretic contact tooth number, which makes the loading capacity of the gears increased dramatically

    三環傳動在足夠大的載荷作用下，實際嚙合齒數會大於理論嚙合齒數，使得三環減速器中齒輪副的承載能力大大提高。
  16. Feasibility study on co - rotating gears transmission of parallel axle with external engagement

    平行軸外嚙合齒輪同向傳動的可行性研究
  17. As external gear pump has the most serious problem of flow pulsation, how to analyze the flow pulsation of gear pump and to optimize the construction parameters of gear pump is especially important for the design and performance improvement of gear pump

    在液壓泵中，以外嚙合齒輪泵的流量脈動最大，因此對齒輪泵流量脈動進行分析，以減小流量脈動為目標，對齒輪泵的結構參數進行優化設計，從而為齒輪泵的設計及齒輪泵性能的提高提供理論基礎。
  18. Crescent gear motor

    內嚙合齒輪馬達
  19. Aimed to the two deficiencies of three - ring gear transmission, the dissertation will analyze these two aspects. the first, according to the finite element model of gear pair of three - ring gear reducer, the dissertation is aimed to analyze the multi - tooth meshing effect of three - ring gear reducer using finite element method, and the number of teeth contacted simultaneously, their load distribution characteristics and the von mises stress change are gained

    針對三環減速器以上兩點的不足之處，本文將對以下兩方面進行分析:首先，本文以三環減速器齒輪副有限元模型為研究對象，利用有限單元法對三環減速器多齒嚙合效應進行分析，得到三環減速器傳動時的實際接觸齒數、嚙合齒載荷分配以及vonmises應力變化規律。
  20. Constant mesh transmission

    常嚙合齒輪傳動
分享友人
分享到 Line

分享到臉書