弧電壓 的英文怎麼說

中文拼音 [húdiànyā]
弧電壓 英文
arc voltage
  • 弧 : 名詞1. [數學] （圓周的任意一段） arc2. （古代指弓） bow
  • 電 : Ⅰ名詞1 （有電荷存在和電荷變化的現象） electricity 2 （電報） telegram; cable Ⅱ動詞1 （觸電） give...
  • 壓 : 壓構詞成分。
  • 電壓 : voltage; electric tension; electric voltage
  1. Voltage reducing devices for ac arc welding machines

    交流電弧焊機的自動降電壓裝置
  2. Guide on methods for evaluating potential for room flashover

    車間飛弧電壓的評定方法指南
  3. Research and development of the high voltage vacuum interrupter

    關于高電壓等級真空滅弧室研究與開發
  4. Insulators string for overhead lines with a nomina voltage above 1000v - ac power arc tests method

    標稱電壓高於1000b架空線路絕緣子串工頻電弧試驗方法
  5. According to the quickly adjustable characteristic of the peterson coil grounding system, this dissertation proposes a new control strategy. when the system is in operation, the strategy can limit the series resonance over - voltage by using the off - resonance method. when fault occurs, the strategy can conveniently suppressing arc by rapidly adjusting the inductance value of the peterson coil to the point, which the resonance with grounding capacitance of the power network is occurred

    依據可控硅控制消弧線圈接地系統的快速可控性，一改傳統的電網正常運行時調節消弧線圈接近於全補償的預調諧方法，提出正常運行時採用脫諧方法抑制串聯諧振過電壓；故障時立即調節消弧線圈電感量達到與對地電容諧振，以利熄弧的新型調節原理和方法。
  6. Wire clipping - ball and high voltage, slow wire sending function developed the arc - starting liability

    焊絲削球和高電壓、緩送絲功能，提高了引弧的可靠性。
  7. Backing weld procedure technique of all - position narrow gap and thick - walled pipe welding is developed about all - position single - pass welding section analysis, wire feeding behavior, weld arc length, welding current analysis, procedure and joint test. the achievement has general guide meaning to producing and testing all - position welder

    從單焊道全位置區段、送絲行為、焊接弧長（電壓） 、電流行為分析、工藝試驗和接頭檢驗等幾方面介紹管道全位置打底焊工藝特點，其研究成果對全位置焊接機的製造和調試具有普遍指導意義。
  8. Abstract : backing weld procedure technique of all - position narrow gap and thick - walled pipe welding is developed about all - position single - pass welding section analysis, wire feeding behavior, weld arc length, welding current analysis, procedure and joint test. the achievement has general guide meaning to producing and testing all - position welder

    文摘:從單焊道全位置區段、送絲行為、焊接弧長（電壓） 、電流行為分析、工藝試驗和接頭檢驗等幾方面介紹管道全位置打底焊工藝特點，其研究成果對全位置焊接機的製造和調試具有普遍指導意義。
  9. Based on researching the function of every kind of eliminating arc loop, new concept was brought up in this paper, and the protective device for eliminating arc and overvoltage was researched and manufactured. when the arc light connecting the ground emerges, the chip synthesizing controller control the vacuum contacter which can be operated with dividing phase and make its fault phase earthed so that the arc light can be dissolved thoroughly

    本文在研究各種消弧線圈的基礎上，提出全新的概念，研製出了消弧及過電壓保護裝置，該裝置在出現弧光接地時，通過單片機綜合控制器控制一組可以分相操作的真空接觸器，使故障相接地，達到徹底消除弧光的目的。
  10. Using the traits of arc adjust itself of the co _ 2 welding, adopting slow - descending feature or even feature of electrical source equipping with system that delivering the welding rod at the invariable speed, then, the arc burning steadily is realized, and the quality of welding is improved

    利用co _ 2氣體保護焊電弧的自身調節特性，採用緩降或平硬特性的電源配等速送絲系統，通過改變電源空載電壓來調節電弧電壓，再利用電弧電壓和熔化速度之間的關系調節焊絲熔化速度使之等於送絲速度，最終實現電弧的穩定燃燒。
  11. In aspect of theoretical stud y, the model of high - pressure welding arcs is established, and the governing equation of high - pressure welding arcs and computing equation of voltage drop of arcs are given

    在焊接電弧理論研究方面，建立了高壓焊接電弧模型並提出了高壓下焊接電弧的控制方程以及電弧電壓的計算方程。
  12. Much works has been distributed to the development of a vacuum system to simulate the outer space and a measurement system to test the arcjet performance. ignition experiments in various operational modes have been done with argon as propellant. macroscopical working parameters including thrust, mass flow rate, voltage, current, inlet pressure and vacuity are obtained by the test measurement system and actual performance parameters including specific impulse, thrust efficiency, ratio of thrust and power and ratio of power and mass flow are calculated

    以氬氣作為推進劑，在不同工況下進行點火實驗，測量獲得了其工作推力、電弧電壓和電流、推進劑流率和弧室壓力等宏觀參數，得到了不同實驗條件下其工作的實際比沖、推力效率、推力/功率比以及比功率等性能參數，分析了推進劑質量流率、電弧功率、電弧加熱發動機電弧室結構尺寸等因素對其性能的影響，為數值模擬研究和實際的低功率電弧加熱發動機優化設計及研製提供了實驗基礎。
  13. In the research of water arcjet, serious oscillation existed in jet and arc voltage was found and it led to unstable work state of arcjet

    目前對水電弧加熱的研究過程中，發現水電弧加熱發動機羽流和弧電壓存在強烈的脈動，不能穩定工作。
  14. Arc suppressing varistor

    消弧電壓敏電阻器
  15. Arc suppressing varstor

    消弧電壓敏電阻器
  16. The results are compared with old ones. it is clear that arc voltage, thrust, specific impulse, efficiency and stability are all improved remarkably

    結構改進后，發動機的弧電壓、推力、比沖等性能以及各工況下的工作穩定性都得到了顯著改善。
  17. The paper establishes a mathematic model that describes the relationship between the arc voltage, the recovery voltage and the arc shield voltage. lt makes a detailed theoretic analysis of the plasma changing laws between contacts and the arc shield gap arc in the arcing process and after - arcing recovery process. the model has achieved the same results as the experiment results

    建立了描述真空滅弧室的電弧電壓、恢復電壓與屏蔽罩電壓之間關系的數學模型，從理論上詳細分系了燃弧過程和弧后恢復過程中，真空滅弧室觸頭間隙和觸頭與屏蔽罩間隙電弧等離子體的變化規律，取得了與試驗結果一致的結論。
  18. This paper designs a device of testing the arc shield voltage in the vacuum interrupter, and makes a study of the arcing and after - arcing recovery characteristics of the arc shield by measuring the arc current, the arc voltage, the recovery voltage and the arc shield voltage

    本文設計了真空滅弧室屏蔽罩電壓測量裝置，並對真空滅弧室在燃弧和弧后介質強度恢復過程兩個階段的電弧電流、電弧電壓、恢復電壓和屏蔽罩電壓進行了全面、系統的波形測試，研究了真空滅弧室蒸汽屏蔽罩在燃弧和弧后介質強度恢復過程的特性。
  19. This paper has studied the structure of the one - sixth turn axial magnetic field of the cup vacuum interrupter with iron core and distribution of the axial magnetic field. the axial magnetic field reduces loss of radial energy of arc post plasma, and makes the arc voltage reduce

    本文著重研究了帶鐵芯的1 / 6匝杯狀縱磁真空滅弧室的結構以及縱向磁場的分佈，縱向磁場的引入降低了弧柱等離子體徑向能量損失，使電弧電壓降低。
  20. Low arc voltage

    電弧電壓低。
分享友人
分享到 Line

分享到臉書