拆卸螺絲 的英文怎麼說
中文拼音 [chàixièluósī]
拆卸螺絲
英文
unscrew- 拆 : 拆動詞[方言] (排泄大小便) excrete
- 卸 : 動詞1 (從運輸工具上搬下來) remove cargo or freight; unload; discharge; unlade 2 (把加在人或牲...
- 螺 : 1. [動物學] (軟體動物) spiral shell; snail; conch 2. (螺旋形的指紋) whorl (in fingerprint)
- 拆卸 : dismantle; disassemble; dismount; tear down; strip; demount; dismounting; disassembly; dismantlin...
- 螺絲 : [口語] screw螺絲把 key screw; 螺絲扳手 monkey spanner; screw; 螺絲刀 screw driver; screw driver b...
-
An analogy is a screwdriver set with removable heads
就好比是帶有可拆卸刀頭的螺絲刀。Remove screw from one side of the splash guard
從防濺保護一側拆卸螺絲。10 base cabinet supported on four leveling screws adjustable in toe base. base cabinet has the removable type back used for access to the plumbing to chase area
所有底櫃有四個可調螺絲支撐,並調節水平。櫃門後背板可用簡單工具方便地拆卸下來以檢修管路系統。The body halves are then separated by removing cap screws and hex nuts
拆卸了蓋螺絲和六角螺母后,閥體就分為兩半。Unscrew and remove bonnet assembly
旋下螺絲,拆卸閥帽組件。Remove junction box cover that is secured by 3 screws. place the cover aside and view the wiring diagram on the inside
通過旋下3個螺絲來拆卸接線盒。把蓋子放在旁邊並察看內面的接線圖。Note : to replace batteries remove ( 2 ) battery case set screws. test kit serial number is located on inside of battery case
注意:更換電池,拆卸2個電池盒固定螺絲。檢測組件系列號位於電池盒內。Remove the cover plate of the relief valve by removing the four connecting screws
通過拆卸四個連接螺絲來拆卸安全閥蓋板。Dismantling tool for general - purpose wire thread insert
普通型鋼絲螺套拆卸工具In order to assure installation reliability and performance of guard against theft device in public or moving environment, we have creatively completed professional design, namely no demountable screws on the exterior, a built - in lock for guard against theft, and special installation way to meet the demand of reliable installation
防盜設計為了克服在公共場所或運動環境下顯示設備的安裝可靠性和防盜性。我們全新設計了具有防盜防破壞功能的安裝結構,即整體外殼無可拆卸螺絲並通過暗鎖進行防盜,且採取橫移下落的方式滿足可靠性的安裝要求。Remove the two hood screws, remove hood
拆卸兩個閥蓋螺絲,拆卸閥蓋。Note : when draining table top models, remove the screw securing the drain access cover. remove the cover by pulling down and away from the water heater
注:對于臺面型熱水器的排水,需要拆卸排水觀察蓋板上的緊固螺絲。通過往下拔將蓋板從熱水器上卸下來。The sealing disk may be removed, if necessary, by removing the screws connecting the keeper plate to the clapper
如果有必要的話,可以通過拆卸將閥瓣連接到承座壓板的螺絲來拆卸密封閥瓣。Back out the service bolt until load is transferred to the screwdriver. continue to back out the service bolt until sufficient clearance is achieved to remove the complete spring mechanism
撤出維修螺栓直到負載轉移到螺絲起子為止。繼續撤出維修螺栓直到有足夠的空間拆卸整個彈簧裝置為止。Remove stem nuts ( 22 ). keep stem from turning by inserting screw driver in slot on end of stem
拆卸閥桿螺母( 22 ) 。通過在閥桿末端的槽內插入螺絲刀來避免閥桿旋轉。Remove compression from spring by turning adjusting screw ( 1 ) counterclockwise
通過反時針方向旋轉調節螺絲( 1 )從彈簧上拆卸壓縮件。To replace seat disc or diaphragm loosen locknut ( 51 ) and back off adjusting screw ( 53 ), remove four bonnet screws ( 24 ) and lift off cage ( 3 ) with spring ( 729 ) and washer ( 61 )
要更換閥座閥瓣或隔膜,則松開鎖緊螺母( 51 )並退出調節螺絲( 53 ) ,拆卸四個閥蓋螺絲( 24 )並將帶著彈簧( 729 )和墊圈( 61 )的籠( 3 ) 。To remove spring mechanism, grasp the screwdriver at the center and pull complete assembly straight out and store in a safe place
拆卸彈簧裝置,要抓住螺絲起子的中心,將整個總成筆直拔出,放置在安全位置。Warning ? while the spring mechanism is removed for check servicing ; never pull the screwdriver out or off the support notches on the arbors. doing so may cause bodily injuries
警告-在拆卸彈簧裝置進行止回閥維修時,絕不要將螺絲起子拔出或拔離彈簧軸上的支撐坑。這樣做可能會傷害閥體。If necessary, the stem and stem seal may be removed from the bonnet by removing the retainer ring and handle and screwing the stem out the under - side of the bonnet
如果必要的話,閥桿和閥桿密封可能要從閥帽上拆卸下來,要在閥帽的下方先拆卸擋圈和手柄,以及閥座上的螺絲。分享友人