接觸整流機 的英文怎麼說

中文拼音 [jiēchùzhěngliújī]
接觸整流機 英文
kontaktum former
  • 接 : Ⅰ動詞1 （靠近;接觸） come into contact with; come close to 2 （連接; 使連接） connect; join; put ...
  • 觸 : Ⅰ動詞1 （接觸） touch; contact 2 （碰; 撞） strike; hit 3 （觸動） touch 4 （感動） move sb ; sti...
  • 整 : Ⅰ形容詞1 （全部在內; 完整） whole; all; complete 2 （整齊） neat; tidy; orderly Ⅱ動詞1 （整理; 整...
  • 流 : Ⅰ動1 （液體移動; 流動） flow 2 （移動不定） drift; move; wander 3 （流傳; 傳播） spread 4 （向壞...
  • 機 : machineengine
  • 接觸 : 1. （交往） come into contact with; get in touch with 2. （沖突） engage 3. （挨上; 碰著） contact; touch
  1. The modulating signals of firing delay angle at the rectifier and firing lead angle at the inverter, and the excitation voltage are chosen to be control variables. the offset of the current of dc line and the extinction angle and the power angle of generator are chosen to be control outputs. then a nonlinear controller is designed for the system under study according to direct feedback linearization theory

    以整流側觸發延遲角的調節信號、逆變側觸發超前角的調節信號以及發電機勵磁電壓作為控制變量，以直流線路電流、逆變側關斷角以及發電機功角的偏移量作為目標輸出，用直接反饋線性化方法設計了系統的非線性控制器。
  2. Using the digital technology improves the performance traditional thyristor welding machine, according to the characters of the double inverse star from rectifier circuit, set the parameters with micro - controller accurately, design the dependable trigger circuit, lead the feedback of voltage for the operation program, so the voltage of main circuit be carried out very steadily

    摘要利用數字控制技術對傳統晶閘管焊接電源進行改進，根據雙反星型晶閘管整流電路的特點，採用單片機進行精確設定，設計了高可靠性觸發迴路，結合電壓反饋進行程序運算控制，實現了主電路輸出電壓的精確調整和可靠運行。
  3. Based on the fundamental theory of eddy current, chip ring transformer was proposed to be used to reduce the eddy current loss for noncontacting synchro

    摘要從渦流產生的基本理論出發，介紹了採用片式環形變壓器結構來減少無接觸式自整角機的渦流損耗。
  4. The principle of ac - dc - ac locomotive is that transformer transforms the high single - phase ac voltage from contact system to lower ac voltage first, then rectifier transforms this ac voltage to steady dc voltage, finally converter transforms this dc voltage to three - phase vfvv ac voltage as the voltage source for asynchronous machine

    交?直?交型電力機車系統的原理是：先將從接觸網獲得的單相交流高電壓經變壓器降壓后，再經整流器變換為平穩的直流電壓，直流電壓經逆變器變換為三相交流電壓，供給機車輪對上的牽引電機。
  5. On - line monitoring of hvcb is the precondition of predicting maintenance, is the key element of reliable run, and is the important supplement to the traditional off - line preventive maintenance in fact, the faults are made by hvcb, no matter in number or in times, is over 60 % of total faults so it has determinative importance for improving the reliability of power supply and this can greatly decrease the capital waste used by - dating overhaul in this paper, the inspecting way of hvcb mechanism characteristic is discussed the concept of sub - circuit protector is presented, the scheme that we offered has been combined with sub - circuit integrality monitoring theory, to ensure that it has the two functions as a whole according the shut - off times at rated short circuit given by hvcb manufacturer, the electricity longevity loss can be calculated in each operation, and the remained longevity can be forecast too an indirect way for calculating main touch ' s temperature by using breaker shell temperature, air circumference temperature and breaker ' s heat resistance is improved in this paper, and main touch resistance can be calculated if providing the load current msp430, a new single chip microcomputer made by ti company, is engaged to develop the hardware system of the on - line monitoring device, and special problem brought by the lower supply voltage range of this chip is considered fully

    高壓斷路器所造成的事故無論是在次數，還是在事故所造成的停電時間上都占據總量60以上。因此，及時了解斷路器的工作狀態對提高供電可靠性有決定性意義；並可以大大減少盲目定期檢修帶來的資金浪費。本文論述了斷路器機械特性參數監測方法；提出了二次迴路保護器的概念，並將跳、合閘線圈完整性監視和二次迴路保護結合起來，給出具有完整性監視功能的二次迴路保護器實現方案；根據斷路器生產廠家提供的斷路器額定短路電流分斷次數，計算每次分閘對應的觸頭電壽命損耗，預測觸頭電壽命；提出根據斷路器殼體溫度和斷路器周圍空氣溫度結合斷路器熱阻來計算斷路器主觸頭穩態溫升的方法，並根據此時的負荷電流間接計算主觸頭迴路的電阻；在硬體電路設計上，採用美國ti公司最新推出的一種功能強大的單片機msp430 ，並充分考慮該晶元的適用電壓范圍給設計帶來的特殊問題；在通信模塊的設計中，解決了不同工作電壓晶元之間的介面問題，並給出了直接聯接的接線方案。
分享友人
分享到 Line

分享到臉書