接觸組合 的英文怎麼說

中文拼音 [jiēchùzǔgě]
接觸組合 英文
contact combination
  • 接 : Ⅰ動詞1 （靠近;接觸） come into contact with; come close to 2 （連接; 使連接） connect; join; put ...
  • 觸 : Ⅰ動詞1 （接觸） touch; contact 2 （碰; 撞） strike; hit 3 （觸動） touch 4 （感動） move sb ; sti...
  • 組 : Ⅰ名詞1 （由不多的人員組成的單位） group 2 （姓氏） a surname Ⅱ動詞（組織） organize; form Ⅲ量詞（...
  • 合 : 合量詞（容量單位） ge, a unit of dry measure for grain （=1 decilitre）
  • 接觸 : 1. （交往） come into contact with; get in touch with 2. （沖突） engage 3. （挨上; 碰著） contact; touch
  • 組合 : 1 （組織成為整體） make up; compose; constitute 2 （組織起來的整體） association; combination3 [...
  1. Stability of rock slopes is generally controlled by the structure of rock masses, especially the soft structure surfaces. analysis of rock mass structures is a key to establish geological models and numerical simulation and a foundation to assess the stability of rock slopes. the weak structure surfaces are mainly bedding planes, faults, joints, schistosity plane and contact zones of intrusive bodies. since they are different in genesis and scale, the rock masses are different in features and mechanical intensities. based on the combination of rock structure bodies, 15 basic modes of deformation and failure of rock slope are systematically summarized. the deformation and failure of rock masses actually result from the recombination and rearrangement of these rock bodies. there are 11 types of rock mass structures and various deformation and failure of bank slopes are present in the reservoir area of the three gorge project

    巖體結構，特別是軟弱結構面對基巖斜坡變形與破壞具有顯著的控製作用，巖體結構模式分析是建立斜坡地質模型和數學模型的關鍵和評價斜坡穩定性的基礎。巖層層面斷裂構造節理裂隙片理與劈理以及侵入體和圍巖的接觸帶等是控制基巖斜坡穩定的軟弱結構面，這些成因不同大小不一的結構面將巖體分割成性質各異力學強度不均的各種巖體結構體，構成了15種基巖斜坡變形破壞的巖體結構基本模式。不同結構體的重新組合與排列是斜坡失穩的內在原因。
  2. With a view to the contactor counterforce, which was calculated by the combination of spring - force and mechanical construction before, had the problem of mechanical matching. the contactor counterforce " one - off " measurement, which is realized by the synchronization testing of the placement based on opto - mechanism and the spring counterforce for the moving component, is put forward the fist time

    針對現階段接觸器反力特性主要採用彈簧力與機械結構組合的計算方法，存在機械配合性問題，將接觸器光機電位移檢測與可動部件彈簧反力特性檢測同步進行，首次實現了接觸器反力一位移特性的「一次性」測量。
  3. The particles distributed hi the matrix of grey cast iron, but some contact each other. the composite layer extend gradually into the substrate. when volume fraction of wc is 36 wt % and 27 wt %, the matrix of the composite is high chromium cast iron, consist of white carbide bars and the austenite. wc particles distributed uniformly, retaining approximately quondam granular form in the composite layer which has an evident interface area with the substrate, with good bonding strength

    對不同碳化鎢體積分數的灰鐵和低鉻鑄鐵基復合材料的微觀組織結構分析表明：碳化鎢體積分數為52時，復合層內基體為灰口鑄鐵組織，顆粒直接分佈在灰鐵基體上，部分碳化鎢顆粒有相互接觸的現象，基材與復合層之間沒有明顯的過渡；碳化鎢體積分數為36 、 27時，復合層內基體為高鉻鑄鐵，由面塊狀的奧氏體和白條狀碳化物組成，碳化鎢顆粒表面固溶於基體組織中，粒形基本保持完整，分佈均勻，與基體構成冶金結合，基材與復合層之間存在一個明顯的平緩過渡區。
  4. Fos + / th + / gfap + and fos + / vp + / gfap + triple labeled n - asc could be found in the mvz, pvn and son respectively ; ( 2 ) under electronic microscope, the astrocytic processes connected closely with the dendrites or axons of the neurons, where the bilateral membranes became thick. we call transiently it electron - dense areas ( edas ). the number of edas increased remarkably following hyperosmotic stimulation ; ( 3 ) when trace retrogradely, wga - hrp was microinjected into the unilateral son, pvn or nucleus of solitary tract ( nts ) respectively using the stereotaxic method, the n - ascs formed by the neurons triple - labeled with hrp / fos / th ( or vp ) and astrocytes labeled with gfap could be found in the mvz, son and pvn respectively ; ( 4 ) after being treated with heperosmotic nacl solution, intracellular calcium concentration in cultured hypothamic neurons and astrocytes increased and then decreased

    腦內gfap陽性結構也明顯增多，其分佈與fos陽性細胞分佈基本一致，表現為胞體肥大、突起粗長； ast緊密包繞在神經元周圍形成神經元- ast復合體（ n - asc ） ；在mvz 、 pvn和son三重免疫組化染色切片上可見到fos + th + gfap +第四軍醫大學博士學位論文和fos vp gfap三重標記asc ； （ 2 ）免疫電鏡下son內星型膠質細胞突起與神經元樹突或軸突之間接觸部位出現增厚的膜結構一電于緻密區（ edas ） ，高滲刺激后數量明顯增多： （ 3 ）將們個mp注入大鼠一側n卜、卜卜或孤束核（ ws ） ，分別在延髓內臟帶（ mvz ） 、 so和pvn內出現fos hrp th 、 fos hrp八p三重標記神經元和gfap陽性標記ast形成的n asc ； （ 4 ）高滲刺激使培養神經元和ast內鈣水平先升高后降低，最後維持在比高滲刺激前稍高的靜息鈣水平上。
  5. The sort, material composite, structure properties and conduction mechanisms of eca ( electrical conductive adhesive ) were discussed in this paper. then three types of ega specimens were designed and made, on which temperature cycles test from - 55 ? to + 125 ? and thermal aging at + 125 ? were carried out. changes of the adhesive strength, eca ' s bulk resistance and contact resistance under the environment stress were summarized and a detailed evaluation on these specimens was given

    本文在全面闡述導電膠的分類組成、物理結構、導電機理的基礎上，設計並製作了三批導電膠樣品，通過對樣品進行長時間的- 55 ? ? + 125溫度循環和125高溫存儲試驗，總結了導電膠粘接強度、體電阻和接觸電阻在環境應力下的變化規律，對三類樣品的長期可靠性做出了全面的評價，並結合導電膠電阻率和「穿流閾值」的計算機模擬，給出了提高導電膠可靠性和電導率的建議，介紹了國內外在高電導率高可靠性導電膠研製方面的一些最新進展。
  6. Based on researching the function of every kind of eliminating arc loop, new concept was brought up in this paper, and the protective device for eliminating arc and overvoltage was researched and manufactured. when the arc light connecting the ground emerges, the chip synthesizing controller control the vacuum contacter which can be operated with dividing phase and make its fault phase earthed so that the arc light can be dissolved thoroughly

    本文在研究各種消弧線圈的基礎上，提出全新的概念，研製出了消弧及過電壓保護裝置，該裝置在出現弧光接地時，通過單片機綜合控制器控制一組可以分相操作的真空接觸器，使故障相接地，達到徹底消除弧光的目的。
  7. Established the system of coordinates of roll testing, getting the parameters of equation of tooth face by solving the non - linear equations set ; according to the differential geometry and meshing principle, deduce the curvature parameters of tooth face and tooth profile, and get the parameters of instantaneous contact ellipse. emulate the contact trace and contact area of the working tooth face, and drawing the instantaneous drive ratio error curve

    建立了克林貝格擺線齒錐齒輪嚙合分析的對滾模型，通過對非線性方程組的迭代求解，得到齒面方程的各個參數;由微分幾何和切齒嚙合原理推導了齒面上齒廓和齒線方向的曲率參數，得到了瞬時接觸橢圓的參數。根據設計參數和機床調整參數繪制了工作齒面的接觸軌跡和接觸區圖形，並求得了瞬時傳動比的誤差曲線。
  8. Compared the results of fea and the data of experiment, we can analyse that the distributing of the seismic stress of polymer - geogrid reinforced material is similar to that of the static stress, but the stress values of them is different ; the seismic similar friction coefficient between the earth and reinforced material fall with the increasing of earthquake acceleration, model acceleration respond along the height of the model, etc. thirdly, according to the comparison and analysis of the model seismic fea results and model experiment data, we can find the polymer - geogrid reinforced earth seismic fea is reasonable, which is composed by earth element, contact element and reinforced material element

    通過對比有限元計算結果和試驗數據，分析得出塑料土工格柵筋材的最大動拉應力的分佈與靜拉應力的分佈沿筋材的埋深大致相同，只是應力的值大小不同；地震作用下土筋間的動似摩擦系數是隨地震加速度的增加而減小；模型沿墻高方向的加速度響應等。接著，根據模型動力有限元時程分析結果和模型試驗數據的比較分析，得出由土體單元、接觸單元和筋材單元組合的塑料土工格柵加筋土非線性動力有限元分析模式的合理性。
  9. The results indicated that the dimension, shape and purity of base material could meet the functional demand of solid lubricant ; the thermal decomposition temperature of ptfe resin exceeds 400 c, but organic and inorganic packing filler added in ptfe made the water absorption rate of composite material increased, melting temperature and decomposition temperature decreased, in the meanwhile oxidative decomposition reaction was accompanied ; polar groups such as c = o, c - o - c and so on in the carbon fiber surface is advantageous to increase compatibility with other components and interlayer shearing strength ; uniform design experimental method could help to find the relationship between formula and frictional property by relatively small tests. the developing trend of each formula ' s friction coefficient could be showed by fitting curve ; the friction coefficient with no copper powder or graphite in formula was relatively big. this fact showed that copper powder and graphite should be used cooperatively ; it was found that when the ratio of copper powder to graphite by weight is 15 : 60, 30 : 30 - 40 and 60 : 15 - 30 respectively, the friction coefficient was relatively small. the degree of crystallinity of pure ptfe reached maximum by air cooling and the abrasion loss also reached maximum among three ones ; at the same time, the abrasion loss of solid lubricant sample was also the biggest among three ones ; when solid lubricant matched with 45 # steel axle or gcrl5 steel axle, lubricant transfer film could be formed on metal surface, thus direct contact between the surface of metal friction pair rings was reduced. their working life was elongated extremely ; there was mainly much graphite, a little ptff, moo3, feso4, cus and so on in lubricant transfer film

    試驗結果表明：所選原料的尺寸、形狀及純度可滿足固體潤滑劑的性能要求；聚四氟乙烯樹脂熱分解溫度超過400 ，但在ptfe中加入無機填料會使復合材料吸水率提高，熔融溫度及分解溫度降低，且伴有氧化分解反應；碳纖維表面含有c = o及c - o - c等極性基團，有利於提高其與其它組分的相容性，提高層間剪切強度；均勻設計試驗方法能夠用較少的試驗次數找出配方與摩擦性能間的關系，擬合曲線基本能表示各配方的摩擦系數發展趨勢；配方中不加銅粉或不加石墨，其摩擦系數均較高，說明銅粉和石墨應該配合使用；當銅粉15份、石墨60份時，銅粉30份、石墨30 - 40份時，銅粉60 、石墨15 - 30份時，摩擦系數均具有較低值；純聚四氟乙烯樹脂在空氣冷卻時結晶度最大，磨損量也是三者中最大的；同時，固體潤滑劑試樣在空氣冷卻時的磨損量也是三者中最大的：不論是固體潤滑劑與45 #鋼軸配副或是固體潤滑劑鑲嵌入銅套后與gcr15鋼軸配副，在金屬表面均可形成潤滑轉移膜，從而減少金屬摩擦副表面間的直接接觸，大大延長其使用壽命;轉移膜中主要含有較多的石墨、少量聚四氟乙烯、 moo 。
  10. Many engineering pairs such as the wheel-and-rail combination described in section 8. 2. 1 generate elliptical contact areas.

    工程上的許多運動組合，諸如821節中所描述的車輪與鋼軌組合，都產生橢圓接觸面。
  11. Chemical industry information not merely embodyed the ordinary chemistry information substance, chemistry manufacture technological process and representative installation introduction are still have, in case contacing legal institutions sulphuric acid ? nitric acid industry system law ( ammonia oxidate law ), synthetic ammonia industry, chlorine and caustic soda are manufacture to electrolysis salt water, along with electrogilding, refine aluminium, iron - smelting and steel - smelting, cement and glass manufacture summarized account, the mineral oil is refined, hence, the chemical industry information education is contrastd against the ordinary chemistry information education, proper such representative means, be living, the means interpreted is in speech oridinarily wholly adoptd in the chemical industry information education, now most of tutors also is adopt the means interpreted in speech, cause that the chemical industry information education is insipid like this, student lack interest to chemical industry information study, but as a result of value the pair foundation, light practice, student may say the become a mere formality to chemical industry information study o since multi - med

    化工知識不僅包含了一般化學知識的內容，還帶有化學生產工藝流程及典型設備的介紹，如接觸法制硫酸，硝酸的工業製法（氨氧化法） ，合成氨工業，電解食鹽水製造氯氣和燒堿，以及電鍍、煉鋁、煉鐵和煉鋼，水泥和玻璃的生產簡介，石油的煉制等，因此，化工知識教學與一般化學知識教學相比，應有其典型的方法。在過去，化工知識的教學一般都採用口頭講解的方法，現在大多數教師也是採用口頭講解的方法，這樣使得化工知識的教學乏味，學生對化工知識的學習缺乏興趣，又因重視雙基，輕實踐，學生對化工知識的學習可以說流於形式。由於多媒體的輔助教學的高效性、形象直觀性、新穎性和多樣性、人工模擬等特點，很適合化工知識的教學，應用多媒體教學化工知識可以解決目前存在的諸多問題，如：模型短缺、組織參觀活動困難、教育經費不足、學生不易觀察等。
  12. New developments in decision theory, artificial theory and dynamic analysis method are applied to evaluation the possible projects. the main contents in this paper are included as follows : first, has improved an format reasoning method based on multiple attribute utility model and knowledgebase theory ; second, has proposed complex utility model by improving the theory of multiple attribute utility ; third, has presented a kind of weapon intelligent decision support system, based on the complex utility model and developed with com / dcom criterion ; forth, this paper also has build the dynamic simulation model for long - rang multiple tube rocket launcher system, and the tire dynamic model has applied in the rocket launcher system dynamic simulation model ; fifth, through building the rocket - launcher contact model, this paper has analyzed the dynamic forces between the rocket and launcher ; finally, this paper has build the evaluation model of the project about improving existing rocket launcher to the launcher that using canister, and get the conclusion through using the widss. the studies in this paper not only proposed scientific warrant to the choice of projects in this pre - studied national defense task about improving existing rocket launcher to the launcher that using canister, but also can give other studied tasks with decision supported

    主要內容包括：在總結決策分析與專家系統規則庫技術的基礎上，提出了融決策分析與專家系統規則庫技術於一體的形式化推理機制，該機制能有效的將定量計算和定性知識融為一體，將規范的決策分析解題過程與專家系統特有的演化推理方法有機結合起來；在多屬性效用理論的基礎上，建立了一般形式的復式效用模型，並實用化了全相關乘式效用模型，提供了較完善的通用建模、分析和解釋功能：引入了com dcom組件技術，開發了基於組件的widss系統，該系統基於形式化推理機制，易於擴展，能夠面向多種決策問題，具有較強的通用性；建立了遠程多管火箭炮全炮動力學模擬模型，將充氣輪胎動力學模型、輪胎和路面的相互作用模型運用於多管火箭炮動力學模擬計算中；利用碰撞接觸理論，對火箭彈在定向器管內的運動受力情況進行了模擬計算；建立了遠程多管火箭炮箱式發射改進方案模型，並利用動力學模擬計算結果在widss系統中進行了方案性能評估。
  13. Through systemic analyzing on spiral helical gear transmission with different basic parameters, the essay found out rules of how can such basic parameters influence spiral helical gear engagement characteristics. so it brings forward the auxiliary assembling mode of adopting one straight gear and one helical gear on condition of little axial angle as well as treasures to ameliorate ill engagement performance on condition of large axial angle, another two jobs of the essay are to clarify the wrong concept that spiral helical gear can only transmit movement but not impetus and to provide a brief and practical method of analyzing contact for gear pairs whose surface equations can be written out directly

    通過對不同基本參數的螺旋齒輪傳動進行系統研究，找出了螺旋齒輪基本參數對其嚙合特性的影響規律，提出小軸交角條件下可採用一直齒輪、一斜齒輪的齒輪副組合方式，給出了大軸交角條件下嚙合性能不良的改進措施。澄清了螺旋齒輪只能傳遞運動不能傳遞動力的誤區，為能夠直接寫出齒面方程的齒輪副進行齒面接觸分析提供了一種簡便、實用的新方法。
  14. Considering the gap between steel lining and concrete lining as the imperfect contact, contact layer is proposed to simulate the gap in the combined work analysis

    針對這種不密實接觸問題，採用厚壁圓環組合環法，提出了在鋼襯和混凝土之間設置接觸層的鋼襯、混凝土襯圈和圍巖三者聯合受力分析方法。
  15. 2 ) applied hertz theory and the force between roller ( or ball ) and orbit, the equation groups for calculating equal contact stress curve are listed. the answer of the equation groups is calculated by utilizing the software matlab. the result of the simulation to this answer proved that the answer is reasonable and the design rule also be discussed from the analysis result

    （ 2 ）應用赫茲接觸理論和所求得的軌道與滾動體之間的正壓力，分別列出以球和滾子作滾動體的等接觸應力軌道曲線方程組，利用matlab求解方程組，並對求解結果進行模擬分析，論證了所求的結果在理論上的合理性，歸納出設計這種液壓馬達的注意事項。
  16. To directly estimate the life of this kind of motor, and to design a orbit curve with the longest life at same condition, this paper gives theoretic research of the equal contact stress inner curve of radial piston motor. the research is divided into four parts : 1 ) taken all forces the piston endured into consideration when radial piston motor working, the force between roller ( or ball ) and orbit is deduced. the simple style of the press expression can be confirmed by ignoring minor influence factors after analysis all factors that will influence this press

    靜壓傳動技術在各類工程機械中得到廣泛的應用，對作為其核心部件的徑向柱塞式低速大扭矩液壓馬達的研究顯得十分重要，為了能直接對這種馬達進行壽命估計，並能在相同工況下求得壽命最長的軌道曲線，本文從設計等接觸應力內曲線的角度對這類馬達作探討性的研究，主要從以下四個方面進行： （ 1 ）綜合考慮徑向柱塞式液壓馬達工作時的各種主要受力狀況，對柱塞組件進行受力分析，並通過模擬分析影響軌道和滾動體間正壓力的各個因素，得到正壓力的簡化表達式。
  17. The task force noted the report of the hong kong university of science and technology ( hkust ) task force ; it also noted that hkust would seek clarifications from government on a number of issues, including the objectives of a merger and the funding implications, before further considering the matter

    中大專責小組知悉香港科技大學專責小組的報告和建議，以及科大校方將與政府接觸，請政府澄清合併的目的及資源投放等關鍵問題，以便科大再作考慮。中大專責小組對此表示歡迎。
  18. In bimetallic thermostats a so - called snap - disc is used as a contact spring ; a fixed temperature switching point can be adjusted via the combination of materials, form and length. the hysteresis is fixed, the switching and reset points are identical

    在雙金屬片自動調溫器中一個所謂的速動盤用作接觸彈簧通過材料型狀和長度的組合可以調整到一個合適的固定的溫度開關點滯後作用是固定的，開關和恢復點是固定的。
  19. Evidently a connection consists of either a loop or a set of non-touching loops.

    很顯然，一個合閘由一個迴路線組成，或者由互不接觸的迴路集合組成。
  20. It was formed in june 2000, following a decade of contacts and co - operation between the two administrations

    經過十年的接觸與合作后，雙方政府在2000年6月成立該合作小組。
分享友人
分享到 Line

分享到臉書