提煉器 的英文怎麼說
中文拼音 [dīliànqì]
提煉器
英文
extractor-
Features : long head that shares about a third of the total length ; a concave forehead ; flat chin stretching to the front ; the spermaceti case containing high fat content is located in the prolapsed occipital bone. besides making candles and ointments, this fat is good ingredient for making precision instrument lubricants
頭部特別長，約占身體長度的三分之一，額部下方凹入，平扁的上頷由此向前伸出，頭頂之外枕骨下垂構成鯨油器，內藏大量油脂，這種油脂除可製成臘燭和油膏之外，更可提煉成維護精密儀器的潤滑劑。This thesis introduces the working principle, craftwork requirement, modeling process, control strategies and the realization of lf refining furnance bottom blowing argon control system. through the study and analysis of bottom blowing argon process control system, the thesis discusses the mean neural network model of controlled object and the mathematical models of the exectors, pwm adjustable pressure controller and pcm adjustable flux controller according to the relevant liquid knowledge and relevant data, including design data, test data and running data. to begin with the craftwork reguirement of bottom blowing argon and the actual instance of the control system, it presents the strategies of fuzzy parameters self - adaptive pid control used in pressure difference inner loop and fuzzy plus pi compound control used in flux outer loop which are based on the above modeling in order to carry out the accurate control of argon flux
本文介紹了lf精煉爐底吹氬過程式控制制系統的工作原理、工藝要求、建模過程、控制策略以及控制系統的實現。通過對精煉爐底吹氬過程式控制制系統進行研究與分析，並根據流體力學的有關知識以及有關數據（其中包括設計數據、試驗數據和運行數據） ，建立起了被控對象的平均神經網路模型和執行機構（即pwm調壓器和pcm調流器）的數學模型。在此模型的基礎上，從底吹氬工藝要求和控制系統的實際情況出發，提出了壓差內環模糊參數自適應pid控制策略和流量外環模糊pi復合控制策略，以實現氬氣流量的精確控制。Item description : kepai grasp spring packaging standard : one unit material : carbon spring steel wires 、 plastic. packing colors : red 、 green 、 blue function : the product was easy using in any time and can boost up strength of your hand, swell blood circulation and advanced agility of your fingers
品名：科牌欖形握力器包裝規格：一隻材料：碳化鋼絲彈簧、塑膠包裝色彩：作用：本產品使用方便隨時可鍛煉你的手勁，增強血液循環，提高手指的靈活性。Application results show the proposed method can deal with mges effectively and provide useful suggestion on instruments checking. thus the number of instruments that must be checked is minimized, the maintenance effort and expense are reduced. 4
敘述了顯著誤差選擇刪除演算法在煉油工業的實際應用情況，說明了該演算法對帶有顯著誤差變量的處理的有效性，並為檢修工作提供了合理建議，使得必須檢修的傳感器數目最少，減小了檢修的工作量和檢修費用。E. sites and equipments resources in rural primary schools through one equipment with various usages, self - made p. e. instruments, transforming traditional p. e. instruments, making use of geography resources and renting p. e. instruments. another is to innovate traditional teaching contents, such as carrying out national and folk p. e. activities, reforming complicate events and putting games into the textbooks
在此基礎上提出了我國農村小學體育教學資源開發的對策：一是切實轉變教育觀念，深刻認識學校體育的最終目標是培養學生體育文化素養與終身體育鍛煉的意識、行為、習慣；二是通過實行「一物多用」 、自製體育器材、改造傳統體育器材、利用自然地理資源、學校體育設施有條件租賃經營等因地制宜，開發農村小學體育場地、器材資源的做事；三是改革傳統教學內容，如開展民族、民間體育活動項目、改造較復雜的體育運動項目、體育教材游戲化等。From different sides such as troops establishment reformation, digitalized army establishment, appearance of new technology, new equipment, new material, etc. the paper analyzes the situation faced with arms development and current situation of external suppression weapon, summarizes and analyzes the development trend of suppression weapon, concludes and abstracts six ways of development trends of fire control system as message integration, system modularization, system architecture subsection, function integration, fire control firing control closed loop and rapid and real - time resolving to realize accuracy, rapid, coordinated integrated weapon control
摘要從部隊編制體制變革，數字化部隊建設，新技術、新裝備、新材料的出現等多方面分析壓制兵器發展面臨的形勢，以及國外壓制兵器發展現狀，總結分析壓制兵器的發展趨勢，並歸納提煉出火控系統應從信息綜合化、系統模塊化、系統體系結構分佈化、功能一體化、火控射擊控制閉環化和快速實時解算等6個方面發展趨勢，以實現精確、快速、協同的綜合武器控制。Over the next two decades, india began to construct and operate nuclear reactors, mine uranium, fabricate fuel and extract plutonium
原能會成立后20年內，印度開始製造核反應器，開采鈾礦，製造核能燃料，從核廢料中提煉鈽。Abstract : the causes for low efficiency of the heater in no. 2 crude unit of jpc refinery are described and analyzed including water leaking of steam soot blower, dew point corrosion caused by steam, soot deposits in convection chamber owning to poor soot blowing, high flue gas temperature, no heat recovery of flue gas, and poor performance of insulation lining, etc. by using sonic soot removing system, flue gas recovery system, spray coating of fiber and rock wool, as well as adjustment of flow scheme accordingly in the technical revamping. the dew point corrosion is completely eliminated, the insulation performance is improved, the heat loss is reduced by 1. 25 %, the flue gas temperature is reduced to about 170, and the heater efficiency is increased from 83 % to more than 90 %
文摘:分析了金陵石油化工公司煉油廠二套常減壓裝置加熱爐存在的因蒸汽吹灰器漏水，蒸汽引起露點腐蝕及吹灰效果差造成對流室積灰，排煙溫度高，煙氣熱量未回收利用以及爐子保溫襯里效果差等問題，提出採用聲波除灰系統、煙氣回收系統、纖維噴塗和巖棉噴塗及相應的流程調整等改造措施.測定結果表明，本次技術改造解決了因蒸汽吹灰器漏水所造成的露點腐蝕問題，提高了保溫效果，減少散熱損失1 . 25 % ，排煙溫度降至170左右，裝置的爐效率由83 %左右提高到90 %以上The causes for low efficiency of the heater in no. 2 crude unit of jpc refinery are described and analyzed including water leaking of steam soot blower, dew point corrosion caused by steam, soot deposits in convection chamber owning to poor soot blowing, high flue gas temperature, no heat recovery of flue gas, and poor performance of insulation lining, etc. by using sonic soot removing system, flue gas recovery system, spray coating of fiber and rock wool, as well as adjustment of flow scheme accordingly in the technical revamping. the dew point corrosion is completely eliminated, the insulation performance is improved, the heat loss is reduced by 1. 25 %, the flue gas temperature is reduced to about 170, and the heater efficiency is increased from 83 % to more than 90 %
分析了金陵石油化工公司煉油廠二套常減壓裝置加熱爐存在的因蒸汽吹灰器漏水，蒸汽引起露點腐蝕及吹灰效果差造成對流室積灰，排煙溫度高，煙氣熱量未回收利用以及爐子保溫襯里效果差等問題，提出採用聲波除灰系統、煙氣回收系統、纖維噴塗和巖棉噴塗及相應的流程調整等改造措施.測定結果表明，本次技術改造解決了因蒸汽吹灰器漏水所造成的露點腐蝕問題，提高了保溫效果，減少散熱損失1 . 25 % ，排煙溫度降至170左右，裝置的爐效率由83 %左右提高到90 %以上By improving surface condition of parts and one shot seal - off clean room grade, using ultrasonic vapor phase cleaning process, the inner parts of vacuum interrupter get cleaner. movable particles have been diminished by automatic current ageing, power frequency hi - voltage ageing and dynamic high current ageing. as the dielectric strength of clearance in vacuum interrupter improved, the probability of re - ignition in test drops evidently
通過提高零件表面加工質量，改善一次封排間的真空衛生條件、制定合理的超聲波氣相清洗工藝提高管內潔凈度，採用自動電流老煉、超高壓工頻老煉、大電流動態老煉等工藝進一步消除真空滅弧室內活動性微粒，可提高真空滅弧室真空間隙介質強度，使真空開關投切電容器組的重燃率大大降低，並通過實驗驗證真空開關投切電容器組的重燃率在製造工藝改進後由原來的10 . 7 %降低至1 . 3 % 。Using fcc flow - reaction mathematical model and boundary condition developed in paper ( i ) and the operational constants in commercial fcc riser, the hydrodynamics of catalysts and the distribution of concentration of catalytic cracking products, as well as the temperature of two - phase along the riser are simulated and predicted
運用已經建立的催化裂化反應的數學模型和模型邊界條件及求解方法，結合煉油廠工業提升管的實際操作參數，模擬預測了催化裂化提升管反應器內催化劑顆粒的流場特徵和原料油反應產物的濃度及氣粒兩相平均溫度的沿程分佈特徵。Abstract : the in servie tubular heaters built early in refineries and chemical plans have low thermal load and low heat efficiency, therefore measures for technical reform are offered, including ( 1 ) enlarging the surface area of convection tubes to increase the thermal load of rhe convection section ; ( 2 ) increasign the heat interchanging area of radiant tubes ; ( 3 ) changing the height of the chimney ; ( 4 ) using new burner with forced air supply to increase calorific capacityu ; ( 5 ) adding air preheater between the convection section and chimney to enhence the temperature of the air entering the furnace ; ( 6 ) adopting high temperature radiant coating to improve the effect of radiant heat interchanging
文摘:針對早期建造的煉油廠和化工廠在役管式加熱爐熱負荷和熱效率低的狀況，提出了若干技術改造措施包括，增大對流管表面積以增大對流段的熱負荷；增加輻射管的換熱面積；修正煙囪高度；換用新型燃燒器，變自然通風為強制供風，以增大燃燒器的發熱量，減小過剩空氣系數，節省燃料2 % 3 % ；在對流段和煙囪之間增設空氣預熱器以提高空氣入爐溫度；採用高溫輻射塗料增強輻射換熱效果，從而增加熱源對爐壁的輻射傳熱量和爐管的傳熱量等。The in servie tubular heaters built early in refineries and chemical plans have low thermal load and low heat efficiency, therefore measures for technical reform are offered, including ( 1 ) enlarging the surface area of convection tubes to increase the thermal load of rhe convection section ; ( 2 ) increasign the heat interchanging area of radiant tubes ; ( 3 ) changing the height of the chimney ; ( 4 ) using new burner with forced air supply to increase calorific capacityu ; ( 5 ) adding air preheater between the convection section and chimney to enhence the temperature of the air entering the furnace ; ( 6 ) adopting high temperature radiant coating to improve the effect of radiant heat interchanging
針對早期建造的煉油廠和化工廠在役管式加熱爐熱負荷和熱效率低的狀況，提出了若干技術改造措施包括，增大對流管表面積以增大對流段的熱負荷；增加輻射管的換熱面積；修正煙囪高度；換用新型燃燒器，變自然通風為強制供風，以增大燃燒器的發熱量，減小過剩空氣系數，節省燃料2 % 3 % ；在對流段和煙囪之間增設空氣預熱器以提高空氣入爐溫度；採用高溫輻射塗料增強輻射換熱效果，從而增加熱源對爐壁的輻射傳熱量和爐管的傳熱量等。The main problem in the company now is to position itself in the market and to work out the development strategy which should be based on the chief objective in sinochem group. through the participation in the group ' s management improvement, the company should as soon as possible improve its software products and go outside to develop its new marketshare besides the inner companies
中化集團經過管理工程改善，將企業的信息化建設作為集團提高競爭力的「加速器」 ，因此電子公司應立足中化內部市場，結合其管理理念，提煉出精華，形成具有特色的軟體產品，並在此基礎上壯大自己，發展自己。分享友人