擺線輪廓 的英文怎麼說

中文拼音 [bǎixiànlúnkuò]
擺線輪廓 英文
cycloidal profile
  • 擺 : Ⅰ動詞1 （安放; 排列） put; arrange; set in order 2 （顯示; 炫耀） display; show off; put on; assu...
  • 線 : 名詞1 （用絲、棉、金屬等製成的細長的東西） thread; string; wire 2 [數學] （一個點任意移動所構成的...
  • 輪 : Ⅰ名1 （輪子） wheel 2 （像輪子的東西） wheel like object; ring; disc 3 （輪船） steamer; steamboa...
  • 廓 : Ⅰ形容詞（廣闊） wide; extensive Ⅱ名詞（物體的外緣） outline
  • 輪廓 : outline; line; lineament; contour profile; rough sketch
  1. Established the system of coordinates of roll testing, getting the parameters of equation of tooth face by solving the non - linear equations set ; according to the differential geometry and meshing principle, deduce the curvature parameters of tooth face and tooth profile, and get the parameters of instantaneous contact ellipse. emulate the contact trace and contact area of the working tooth face, and drawing the instantaneous drive ratio error curve

    建立了克林貝格擺線齒錐齒輪嚙合分析的對滾模型，通過對非線性方程組的迭代求解，得到齒面方程的各個參數;由微分幾何和切齒嚙合原理推導了齒面上齒廓和齒線方向的曲率參數，得到了瞬時接觸橢圓的參數。根據設計參數和機床調整參數繪制了工作齒面的接觸軌跡和接觸區圖形，並求得了瞬時傳動比的誤差曲線。
  2. As both the meshing point and ball ' s center are on the given cylinder, a general method for developing the cam ' s profile is studied. it is proved that the profile of positive and negative transmission is unique if the face gear, the difference between face tooth number and ball number and the diameter of ball are the same. the concrete expression of meshing cam on given spatial cycloid profile, and the characteristics of the profiles are discussed

    論文的主要工作包括： 1 、根據嚙合點和鋼球中心軌跡均在同一圓柱面上的特點，研究了給定端齒齒廓條件下求解凸輪齒廓的一般方法；論證了在給定端齒、齒差數和鋼球直徑相同的條件下，正負齒差嚙合齒廓的唯一性；討論了端齒為球面擺線時，凸輪齒廓的具體表達式，並研究了該齒廓的性質。
  3. On the basis of the known actual contour equation of cam in the disk typed cam mechanism with swinging oblique bottomed follower, this paper expounded another method for determining inversely the track equation of cutter center and the motion law of follower, and three key techniques in numerical inverse seeking were solved successfully by adopting the method of curve matching

    摘要根據已知擺動斜底從動件盤狀凸輪機構的凸輪實際廓線方程，闡述了反求確定刀具中心軌跡方程和從動件運動規律的另一種方法，並採用曲線擬合等方法成功地解決了數值反求中的3個關鍵技術。
  4. This paper provides the general equations of the theoretical contour line and the actual contour line of roller translation follower and roller oscillating follower disc cam in the polar coordinates system and the rectangular coordinates system, respectively. the equations are not only fit for the different layouts of the relative position of follower and cam, but also fit for the different types of cam contour

    分別給出了滾子直動從動件和滾子擺動從動件盤形凸輪的理論廓線及實際廓線在極坐標系與直角坐標系下的通用方程，它們對于從動件與凸輪相對位置的不同布局方式及凸輪輪廓的不同類型均適用
分享友人
分享到 Line

分享到臉書