斷點命令 的英文怎麼說

中文拼音 [duàndiǎnmìnglìng]
斷點命令 英文
breakpoint command
  • 斷 : Ⅰ動詞1 （分成段） break; snap 2 （斷絕;隔斷） break off; cut off; stop 3 （戒除） give up; abstai...
  • 點 : Ⅰ名詞1 （液體的小滴） drop （of liquid） 2 （細小的痕跡） spot; dot; speck 3 （漢字的筆畫「、」）...
  • 斷點 : breaking point; breakpoint斷點操作 break-point operation; 斷點指令 break-point instruction [order]
  1. “ with every car bomb that takes civilian toll, every insurgent ' s bullet that finds it mark, every roadside explosive that maims or kills one of our own brave men and women in uniform, the sacrifices mount and the result is anything but satisfactory

    「每一次汽車炸彈造成平民傷亡、每一發暴動者的子彈命中目標、每一次路邊爆炸給我們身穿制服的勇敢的男女軍人們帶來重傷或死亡，犧牲在不斷的增加，而結果卻一點也不令人滿意。 」
  2. Defined watchpoints can be listed along with breakpoints with the info watch command the command is equivalent to info break and watchpoints can be enabled, disabled and deleted using the same syntax as for breakpoints

    Info watch命令將列出已定義的監視點和斷點（此命令等價于info break ） ，而且可以使用與斷點相同的語法來啟用、禁用和刪除監視點。
  3. The commonly used breakpoint commands are

    常用的斷點命令有
  4. This command is useful for continuing a program when a class load event, exception, or breakpoint stops the debugger

    此命令對于在類加載事件、異常或斷點停止調試器時繼續程序很有用。
  5. The debug monitor proides a set of primitie commands to iew and modify memory locations and registers, create and remoe breakpoints, and execute your program

    除錯監視程序提供一個簡單的命令集來顯示和內存地址和寄存器、建立和移除斷點，並且運行你的程序。
  6. The debug monitor provides a set of primitive commands to view and modify memory locations and registers, create and remove breakpoints, and execute your program

    除錯監視程序提供一個簡單的命令集來顯示和內存地址和寄存器、建立和移除斷點，並且運行你的程序。
  7. Command applies the breakpoint on all processors in an smp system

    命令對smp系統中的所有處理器應用斷點。
  8. You cannot set or clear stop statements using debugger commands, as you would a breakpoint

    不能使用調試器命令設置或清除stop語句，而對于斷點卻可以使用調試器命令。
  9. Sets a breakpoint on a symbol recently displayed with the

    命令顯示的符號處設置斷點；
  10. Command lists the current set of breakpoints

    命令列出當前的斷點集。
  11. Breakpoints can be set to unconditional using the condition command specifying a breakpoint number without an expression, for example condition 1 sets breakpoint 1 to unconditional

    使用condition命令時，如果指定斷點編號但又不指定表達式，可以將斷點設置成無條件斷點，例如， condition 1就將1號斷點設置成無條件斷點。
  12. Commands can be used provided the architecture supports use of hardware registers to apply read and write breakpoints

    命令（假如體系結構支持使用硬體寄存器）來應用讀寫斷點。
  13. A motion to disallow a member s vote on grounds of his direct pecuniary interest may be moved without notice by any member immediately upon the statement by the president, chairman of a committee of the whole council or chairman of his judgment on whether there is a required majority or, if a division has been ordered, upon his statement of the numbers of members recorded in the division

    以某議員有直接金錢利益為理由將其表決作廢的議案，可無經預告由任何議員在立法會主席、全體委員會主席、委員會主席或小組委員會主席說出按其判斷原議案是否獲得所需的過半數票后，立即動議；如有命令進行點名表決，有關議案可在立法會主席、全體委員會主席、委員會主席或小組委員會主席說出點名表決所記錄的有關議員數目后，立即動議。
分享友人
分享到 Line

分享到臉書