方位圓盤 的英文怎麼說

中文拼音 [fāngwèiyuánpán]
方位圓盤 英文
azimuth disc
  • 方 : Ⅰ名詞1 （方形; 方體） square 2 [數學] （乘方） involution; power 3 （方向） direction 4 （方面） ...
  • 位 : Ⅰ名詞1 （所在或所佔的地方） place; location 2 （職位; 地位） position; post; status 3 （特指皇帝...
  • 盤 : Ⅰ名詞1 （盤子） tray; plate; dish 2 （形狀或功用像盤的東西） sth shaped like or used as a tray pl...
  • 方位 : position; bearing; direction; points of the compass; placement
  1. Any of the32 equal divisions marked at the circumference of a mariner ' s compass card that indicate direction

    羅盤上三十二個方位之一用來指示方向的水手羅經刻度盤圓周上標記的三十二等分中之一
  2. This drilling adopts crank connecting link and walking beam percussion mechanism, which make the drilling possess two percussive functions, normal drilling takes connecting link impact as main mode, when encountering special situation and the connecting link impact can not drill, it can transform into hoisting impact, the stroke length can be modulated, it realizes automatic percussive drilling due to continuous operating of connecting link percussive mechanism, these can enhance drilling efficiency and relieve labor intensity ; it adopts pumping reverse circulation to drain slag, which not only resolves the drilling difficulty in special stratum such as pebble and gravel stratum and hard stratum, but also resolves the problem that the percussive drill ' s efficiency is low ; it adopts spur gear differential mechanism as double cylinders lazy tongs of main hoist, which not only ensures the balance state of drilling tool, but also reduces the mechanical design, and reduces the cost ; the bottom plate traveling motion of this drilling machine adopts walking type ; the drilling tower adopts hydraulic pressure uprising, and reduces the assistant operating time

    該鉆機採用曲柄連桿、游梁式沖擊機構，使鉆機具有兩種沖擊功能;正常鉆進以連桿沖擊為主，遇到特殊情況，用連桿沖擊不能鉆進時，可轉為卷揚沖擊，沖程可調，因連桿沖擊機構連續工作，所以實現了自動沖擊鉆進，可提高鉆進效率，減輕勞動強度;採用泵吸反循環的方式排渣，既能有效解決卵礫石地層、堅硬地層等特殊地層鉆進的困難，又很好地解決了沖擊鉆機效率低下的問題;採用直齒圓柱齒輪差速機構作為主卷揚的雙筒同步機構，既保證了鉆具處于平衡狀態，又大大簡化了該機構設計，降低了成本;該鉆機底盤行走移位採用步履式;鉆塔採用液壓起立，減少了輔助作業時間。
  3. At first, according to the concrete requirement of the servo control system, a collective scheme, which provide guarantee to meet the requirements of the global performance, is established. in this scheme, the structure of gimbal and the torque motor driven mode are adopted, and angle measurement is accomplished by inductosyn and velocity measurement is accomplished by dynamically tuned gyro respectively

    首先，根據目標真值測量設備伺服系統的具體要求，確定了地平式常平架結構，力矩電機驅動，分別採用動力調諧式速率陀螺儀及圓盤式感應同步器作為速率及位置反饋元件這一總體方案，為伺服系統滿足整體性能指標要求提供了保證。
  4. A semi - analytical and semi - empirical method is used to formulate a displacement solution for the circular disc with a pair of flattened areas under diametral compression

    摘要用半解析半經驗的方法推出圓盤對徑壓縮的一個位移解，該公式可以估算力作用點有微小平臺時直徑的壓縮位移。
  5. In chapter 6, the usage of floater ' s algorithm on a disk is discussed which is for geometric reconstruction of surface with four edges using double cubic b - spline surface, and the algorithm is generalized to a cylinder and a mobius

    第六章討論了floater關於四邊拓撲曲面的雙三次b樣條幾何重建方法在圓一摘要浙江大學博士學位論文一盤拓撲曲面上的應用，並將其推廣到平環與mbbius帶上。
  6. Because the controller is easy to get the position of rotor by the encoder, we can continuously rotate the flux of the armature rotor by applying spwm method to the control system. the continuous rotation of the flux of armature make the output torque of motor has no ripple

    由於通過編碼盤可以輕易獲得精確的電機轉子位置信號，故運用spwm調制方法可以使得無刷機的電樞磁場按照圓形軌道連續旋轉，從而實現輸出轉距無脈動。
  7. In the first part, firstly, the main dimensions of oar blade and propeller boss and other parameter of varivec propeller are selected. then, a suit of viable mechanism to control the work state of varivec propeller is designed, which is different from the mechanism designed by the japanese. it ' s principle is similar with the cycloid propeller

    在機構設計部分，本文首先確定了全方位推進器的槳葉及槳轂的主尺度以及其他的相關的參數，然後設計出一套可行的與擺線推進器工作原理相仿的調距機構用來對全方位推進器的工作狀態進行控制，該機構與日本的全方向推進器的連桿圓盤機構完全不同。
分享友人
分享到 Line

分享到臉書