曲軸的 的英文怎麼說
中文拼音 [qūzhóude]
曲軸的
英文
bent-
The throw of the crankshaft, i. e. the distance between the main journal and the big end centers, controls the length of the stroke
曲軸的擺幅,即在主要曲頸和連桿大頭末端中心之間的距離,控制著沖程的行程。As the crankshaft rotates, the crankpin swings in a circle around the shaft.
隨著曲軸的轉動,曲柄銷繞主軸作圓周擺動。The crank is an offset section of the crankshaft.
曲柄是曲軸的偏置部分。The ratio of the crankshaft to the revolutions of the camshaft is 2∶1.
曲軸的轉速與凸輪軸的轉速之比是21。Stress analysis of finite element to jzh25 homogenizer crankshaft based on ansys
25型均質機曲軸的應力分析It is applied to sorts of locomotive engine, in course of revolving of crank and connecting rod mechanism, there are revolving of the crankshaft, swinging of the connecting rod and reciprocating motion, so its motion state is complex, and periodic unbalanced force, by a few components, is great
曲柄連桿機構在高速運轉過程中,有曲軸的轉動、連桿的擺動及活塞的往復運動,其運動狀態復雜,各個部件所產生的周期性不平衡慣性力大,是引起發動機振動的主要原因。Repair of the oxyacetylene welding of the crank anxle
曲軸的氧乙炔焰噴焊修復3d - photoelasticity analysis of the crankshaft
曲軸的三維光彈性分析This method of diesel engine fault diagnosis is feasible theoretically. while the fault diagnosis system using this method is rare, just because the crankshaft instantaneous angular acceleration measurement is demanding, such as, good frequency response, high precision
這種柴油機故障診斷的方法在理論上是可行的,但目前這種成型的系統不多,究其原因是測量曲軸的瞬時角加速度需要系統具有良好的頻率響應特性與高精度。In this paper, the bend stress of engine crankshaft was analyzed by the finite element method ( fem ). an one - fouth crankthrow fe model is used to analyze it taking different boundary conditions into account
本文用有限元法計算分析了發動機曲軸的彎曲應力。採用1 4曲拐有限元模型對不同邊界條件進行了研究,計算了安全系數。Remodeling design of bent axle of x2110 marine diesel engine
2110船用柴油機曲軸的改型設計Specification for magnetic particle flaw inspection of finished machined solid forged and drop stamped crankshafts
成品機制整體鍛造和落鍛沖壓曲軸的磁粉探傷規范Several years, we instst scientific developing strategies, widly admit talents, trying our best to develope low - voicebent - axis and we re gained dependable effects
幾年來,我公司堅持科技振興的戰略,光招賢才,致力於低噪音曲軸的攻關新產品開發,取得可靠的成效。Standard specification for continuous grain flow forged carbon and alloy steel crankshafts for medium speed diesel engines
中速柴油機用連續晶粒流動鍛造碳鋼及合金鋼曲軸的標準規范The radius of a circle described by a crank, cam, or similar machine part
(曲軸的)半徑曲柄、凸輪或類似機器部件形成的圓的半徑Meanwhile, the fracture was accelerated due to the uneven surface hardness and the unreasonable distribution of the hardening layer on the crankshaft, and the bad lubrication condition in service
同時軸左頸表面硬度不均勻、淬硬層分佈不甚合理,工作過程中潤滑條件差,加速了曲軸的斷裂。Refrigerating compressor k - 5222 crank shaft repairing technology
5222曲軸的修復技術It fits onto the rear of the crankshaft
它安裝在曲軸的後面。Wear and repair of engine crankshaft
發動機曲軸的磨損與修復An inspection is completed on pistons and connecting rods and a report on the feasibility of repair is given to the supervisor
活塞連桿曲軸的檢驗報告已經出據,並維修的可行性報告已交付給相關的監督人員。分享友人