曲軸齒輪 的英文怎麼說

中文拼音 [qūzhóuchǐlún]
曲軸齒輪 英文
crankshaft gear
  • 曲 : 曲名詞1 （一種韻文形式） qu a type of verse for singing which emerged in the southern song and ji...
  • 軸 : 軸Ⅰ名詞1. （圓柱形的零件） axle; shaft 2. （對稱部分的直線） axis 3. （圓柱形的纏繞器物） roller; spool Ⅱ量詞（用於纏在軸上的線以及裝裱帶軸子的字畫）
  • 齒 : Ⅰ名詞1 （牙; 牙齒） tooth 2 （物體上齒形的部分） a tooth like part of anything 3 [書面語] （年齡...
  • 輪 : Ⅰ名1 （輪子） wheel 2 （像輪子的東西） wheel like object; ring; disc 3 （輪船） steamer; steamboa...
  • 齒輪 : gear [rack; toothed] wheel; （toothed） gear; wheel gear
  1. When the gears are engaged, the crankshaft keeps the car moving.

    而曲軸，在齒輪箱掛擋時，又使汽車持續運動。
  2. Thus, using modified - roll method, 4 - axis cnc spiral bevel gear machine can manufacture hypoid gear

    這樣，在四軸數控銑齒機上可以實現變性法加工準雙曲面齒輪。
  3. The thesis developed the optimization design software of geometric parameter for the worm gear including strength check module, the drawing contact lines module, the change lines of tooth thickness of worm, and the parametric modelling software for the reducer which includes parametric modelling of parts and assembly. the cad prototype system is very convenient because of its accessible interfere, simple operation and written in chinese. by input design parameters ， the cad system can make optimization design and strength check for the worm gear ， draw contact lines of tooth flank of worm - gear and change line of tooth thickness of worm ， judge if the tooth flanks of worm undercut and if the sideward tooth of worm - gear hob come to a point ， make project design and structure design for the reducer and draw its 2d parts and assembly

    研究和開發了平面二次包絡環面蝸桿傳動的參數優化設計和校核軟體系統：包括幾何參數設計計算模塊，強度校核模塊，繪制齒面接觸線模塊，蝸桿齒厚變化曲線模塊和蝸桿根切判別模塊；開發了平面二次包絡環面蝸桿減速器外形與結構尺寸數據庫以及傳動效率數據庫，建立了平面二次包絡環面蝸桿傳動公差及極限偏差數據庫；開發了平面二次包絡環面蝸桿減速器參數化建模軟體：包括零部件的參數化建模模塊和裝配圖的參數化建模模塊，其中零部件的參數化建模包括蝸桿軸系的參數化建模、蝸輪軸系的參數化建模、箱體的參數化建模、端蓋的參數化建模、軸承的參數化建模和其它零部件的參數化建模軟體模塊。
  4. Finally, in consideration of the characteristics of the differential balance mechanism, a more accurate virtual prototype of the mechanism is established and the simulation is carried out in the software environment of adams. the angular velocity curves of the relevant parts and the natural frequency of the mechanism are got. the results may be helpful to the improvement and the application of the mechanism

    最後，綜合考慮了輪齒嚙合剛度、搖臂軸扭轉柔性及齒輪傳動回差對差動平衡機構的影響，建立了能夠比較完整地反映該機構動態特性的虛擬樣機模型;在adams軟體環境下，對差動平衡機構的虛擬樣機模型進行了動態模擬，得出了能反映該機構動態特性的關系曲線，並確定了其固有頻率，為該機構的改進及其在月球車上的實際應用提供了參考依據。
  5. Then the experiment platform of the hypoid gear system was set up, and the lateral, longitudinal and axial vibration response of the bearing and the vibration acceleration response on the surface of the gearbox were measured

    搭建了準雙曲面齒輪傳動系統的實驗平臺，測量了準雙曲面齒輪箱軸承座的橫向、縱向和軸向振動響應和箱體表面振動加速度響應。
  6. But a camshaft driven directly by the crankshaft gear turns in the opposite direction

    但是凸輪軸被曲軸齒輪直接驅動，其將在相反方向上轉動。
  7. The camshaft and crankshaft gears can be connected directly, or meshed. this type of operating linkage commonly is used on older six - cylinder, inline engines

    凸輪軸和曲軸齒輪可能被直接連結，或者相嚙合。這類操作聯動通常被用在更老的六氣缸，直列發動機上。
  8. Crankshaft timing gear

    曲軸正時齒輪
  9. Crankshaft fluctuation sensor ( ckf ) is located near the bottom of the timing cover where it generates a signal as the crankshaft timing chain sprocket rotates past it

    曲軸位置傳感器安裝在定時器殼底部附近，產生一個曲軸定時鏈輪齒通過的信號。
  10. A crankshaft fluctuation sensor ( ckf ) is located near the bottom of the timing cover where it generates a signal as the crankshaft timing chain sprocket rotates past it

    曲軸位置傳感器安裝在定時器殼底部附近，產生一個曲軸定時鏈輪齒通過的信號。
  11. The monitoring sites and the signal types of various common faults are illustrated for early diagnosis, including misalignment or off balance of the rotor, shaft bending, loosing of a part, fluid induced vibration and damages of rolling - bearing or gear, etc

    闡述了振動測試點和測量信號類型的選擇方法，給出諸如轉子不平衡、軸彎曲變形、轉子不對中、部件松動、流體誘發振動及滾動軸承、齒輪損傷等常見故障的診斷方法。
  12. The paper has begun with existing driving mechanism of horizontal barrel finishing equipment and analysed the reason that creates the family of crank parts machining quality problem. the transmission plan of noncircular gears connect crank - slider mechanism has been presented and mathematical model of driving mechanism has been established. by way of programming operation, simulation analysis and parameter optimization, the feasibility of new plan has been proofed

    本課題從現有臥式滾磨設備的傳動機構入手，對造成曲軸類零件加工質量問題的原因進行了分析，提出引入非圓齒輪串聯曲柄滑塊機構的傳動方案，建立了傳動機構的數學模型，通過計算機編程運算及模擬分析和參數優化，驗證了所提新方案是可行的。
  13. On some engines, a metal chain is used to connect the crankshaft and camshaft gears. most push - rod engines and some ohc engines have chains

    在一些發動機上，金屬鏈被用來連結曲軸和凸輪軸齒輪。大多數推桿發動機和一些頂置凸輪軸發動機都有鏈。
  14. The curvature interference of the gear and the influence of radius of the mill - cutter, axial misalignment, and center distance on meshing are analyzed. based on these analyses, propose two methods to achieve point - contact : to change the radius of the mill - cutter and increase the center distance

    在分析了弧齒線圓柱齒輪的嚙合傳動不產生曲率干涉的條件和刀盤展成半徑、軸線平行度誤差、中心距對嚙合影響的基礎上，提出了點接觸弧齒線圓柱齒輪實現的兩種方案:調整刀盤展成半徑和增大中心距。
  15. Compared with the traditional cantilever structure, the bearing life of two - terminal bracing structure is improved by 17. 51 times, while the contact stress of gear tooth is reduced by 45. 7 %, and the bending stress of gear tooth is reduced by 62. 8 %

    與傳統主動齒輪懸臂結構相比兩端支撐結構的軸承壽命提高了17 . 51倍、輪齒接觸應力降低45 . 7 % 、輪齒齒根彎曲應力減小62 . 8 % 。
  16. The pinion gear is on the same shaft as the motor armature and rotates at the same speed

    小齒輪如馬達電樞般在同一曲軸上，且以相同的速度轉動。 ？
  17. Through analysis the reasons influencing measuring stability have been found out, which are the flexure strain and structure resonance produced by the transmission axle under the function of the gearing - in force of the reduction gear

    雖然與傳統的測量方法一致，但經過理論分析，得出了這種測量方式機械結構影響測量穩定性的原因，即傳動軸受減速器齒輪嚙合力作用?生的彎曲應變和結構諧振對測量精度影響最大。
分享友人
分享到 Line

分享到臉書