有限變量數 的英文怎麼說

中文拼音 [yǒuxiànbiànliángshǔ]
有限變量數 英文
finite number of variables
  • 有 : 有副詞[書面語] （表示整數之外再加零數）: 30 有 5 thirty-five; 10 有 5年 fifteen years
  • 限 : Ⅰ名詞（指定的范圍; 限度） limit; bounds Ⅱ動詞（指定范圍, 不許超過） set a limit; limit; restrict
  • 量 : 量動1. （度量） measure 2. （估量） estimate; size up
  • 數 : 數副詞（屢次） frequently; repeatedly
  • 有限 : limited; restricted; finite; a little; not much
  1. In view of bearing capacity of the elastoplastic theory analysis, the author made a comparison between the achieved bearing capacity limit load pi / 4 of round base ( space problem ) and the limit load pi / 4 of bar groundwork foundation design ( plane problem ) from soil mechanics at home and abroad as well as foundation criterion, and explained why the value of formula in present design criterion from soil mechanics is inclined to be conservative. in the light of the author ' s many years experience of vibration test on the spot and the research work of relevant projects, the author worked over the dynamic pile testing of the bearing capacity of foundation and batholith, and gathered the parameter of dynamic analysis and testing. the author also talked over the difficult point of pile foundation design criteria in present batholith engineering world, i. e. the confirmation of batholith bearing capacity of pile end, from the following aspects : a ) confirmation of single axis counter - pressure strength of rock in house ; b ) f. e. m calculation of elastoplastic model ; c ) calculation of soil mechanics ; d ) deep well load test

    然後，對巖土工程領域至今尚未解決，甚至不為人注意的考慮地基變形的地基承載力問題進行了實用化的探討，提出了考慮地基變形的地基承載力上程計算方法；對基於彈塑性理論分析的地基承載力國內尚未見報道的空間問題得到了圓形基礎（空間問題）的承載力界限荷載p _ （ 1 / 4 ） ，並與國內外土力學專著及地基基礎設計規范中的條形基礎（平面問題）的界限荷載p _ （ 1 / 4 ） ，進行了對比，從而定量上解釋了目前設計規范引用土力學承載力公式值偏於保守的這一情況；根據本文作者多年從事現場地基工程振動試驗及相關課題的研究工作，本文以截頭錐模型模擬地基，對地基（巖基）承載力的動測法進行了研究，為各類地基（包括巖基） ，匯總了動力分析和檢測川的參數：針對日前巖土工程界應用樁基設計規范中的難點? ?樁端巖基承載力的確定問題，從巖石室內單軸抗壓強度確定、基於彈塑性模型的有限單元法計算、土力學計算及深斤載荷試驗四方面進行了深入討論；本文作者根據多年現場載荷試驗的工程實踐，對深井荷試驗裝置的核心部分? ?反力裝置，設計了側壁支撐反力加載系統，該加載系統具有實用、簡便、穩定及安個等優點。
  2. The scielltific computational theories and methods on bird strike to the windshield of aircraft have been systematically studied and summed up in this thesis, such as fem comptltational principles and procedures to elastic dynamic problems under the conditions of small and non - linear finite deformation, 3d viscous elastic constitutive theory and incremelltal expression under the consideration of the rate effect of non - metallic materials like the aircraft windshield, and the numerical compatational principles and key constitutions for impact - contact dynamic subjects

    2 、系統學習並歸納總結了鳥體撞擊風擋結構問題中的科學計算理論與計算方法。按照鳥撞問題數值計算方法逐步深入的思路，系統總結了小變形結構動力學有限元數值計算方法、有限變形的幾何非線性有限元數值計算方法、粘彈性體非線性形變的本構物理關系；對于實施復雜結構有限元動力學計算的載荷增量方法提出了對newmark差分的改進以及進行材料與幾何非線性數值計算的細致步驟。
  3. The calculation modes of the coefficient of shrinkage and creep of the bulgy core concrete in steel tube are discussed. based on a few reasonable hypotheses and the stress - strain relation of concrete acquired by the " adjusting valid modulus depending on load time " method, a compact formula is reasoned out, which is applied to calculate the equivalent elastic modulus of the bulgy core concrete considering the affection of shrinkage and creep. so, the analysis of the affection on cfst arch bridge by shrinkage and creep can be progressed by pole - girder fem, further more, the analysis precision is quite high

    本文還對核心膨脹混凝土特殊的收縮、徐變系數計算模式展開了探討，在合理的假設前提下，採用「齡期調整的有效模量法」得到的混凝土的本構關系，推導出鋼管內核心混凝土在考慮徐變影響后的等效彈性模量計算公式，並以此為基礎採用桿系有限元方法來對鋼管混凝土拱橋進行較高精度的收縮徐變分析。
  4. The gravity analysis is carried out especially for the synthetic fused silica and calcium fluoride used in 193nm lithographic objective as well as the optical elements with structural sizes of ( 200mm ~ ( 300mm. large numbers of analysis data for surface shape error are obtained by using algor finite element analysis software. then these data are plotted into curves and comparison analysis will be carried out, finally the measures and schemes for reducing gravity deformation are proposed

    因此，本論文重點對大口徑光學系統在高精度光學鏡頭裝校中，因重力變形進行了詳細的分析研究，特別針對193nm光刻物鏡系統所使用的材料sytheticfusedsilica和caleiumfluoride以及用到的結構尺寸200mm ~ 300mm光學零件進行了重力變形分析，使用algor有限元分析軟體獲得了大量的面形誤差分析數據，然後將這些數據繪成曲線進行對比分析，最後提出了減小重力變形的措施與方案，並進行了實驗，驗證了分析結果是正確的，減小重力變形的方法是有效的。
  5. So it is impossible for enstatite to decompose to oxides between 50 to 140gpa. ( 5 ) the bulk modulus k0s and its first derivative of pressure k0s " were calculated from the experimental hugoniot data, by using eularian limit strain theory

    3 ）根據本文頑火輝石hugoniot實驗數據（結合前人的實驗數據l用歐拉有限應變理論計算得到的頑火輝石零壓炸彈性模量及其對壓力的一階導數為： k叮一266gpa ， k ； ，二4
  6. 4. the principle of the experiment including the isdg method is introduced. and the effect of shape and distance of the indention on strain measurement is analyzed

    4 ）介紹試驗設備的組成及試驗原理，通過理論推導和有限元數值模擬分析了拉伸試樣的凹痕標記對應變測量的影響，對isdg （ interferencestrain displacementgauge ）方法進行了深入的研究。
  7. With the limitation of our learning level and objective case, the variables x1, x2, . ., xm being taken into account are only a part of all relevant variables. the other variables being ticked out may well be more important. so it is not plenty to think about the factor ' s influence on forecasting, the sample ' s information also play its role on forecasting

    一般情況下，對因變量y有影響的因子往往為數極多，而由於我們的認識水平和客觀條件的限制，在問題中考慮進來的自變量x1 ， x2 ， . . . ， xm只是全部有關變量的一部分，其它未被考慮進來的變量完全有可能是更重要的，可見，僅僅著眼于因子對預測的影響顯然不夠，樣品信息也對預測起著重要作用，而且每個樣品對預測所起的作用還互不相同。
  8. The limit theory of law of the iterated logarithm have received more and more attentions, especially about identical independent random variables. but up to now, the studies are only for partial sums and, have n ' t shown any concern on the special finite partial weight suras. however, the partial sums and partial weight sums not only have the osculating aspects, but also have essential difference between them. so the studies for these play an important role in theoretical and applied setups

    因此對重對數律的研究引起了國內外學者的興趣，對獨立同分佈的隨機變量，許多學者做了大量的研究工作，但迄今為止這方面的研究仍限於部分和數列的重對數律，很少涉及到特殊加權和的領域，而部分和與加權和之間既有密切聯系，又有本質不同，因此，這一問題的研究具有一定理論意義和應用價值。
  9. Prime number theorem of an algebraic function field of dimension 1 over a finite field

    有限域上單變量代數函數域中的素數定理
  10. Taking the contact stress, bend stress stiffness and temperature stress as the condition, taking the weight of the kiln tyre as optimization aim function, the redia and the width of the tyre are optimized general optimize methods just consider the affecting of the parameters to aim function, but in fact, structural parameters ( such as structure dimension, interval and so on ), physics and dynamics ( damp factor, conduct factor, friction factor material ' s elastic module strength limits and so on ), which would be changed after used. the difference are called discrepancy robust design ' s basic concept is : all design parameters " discrepancy will affect the aim funct ion and arouse the quality target discrepancy

    一般的優化方法，僅僅考慮了參數對其目標函數的影響，而實際情況下有些參數是變化的，產品的結構參數（如幾何尺寸、間隙等） 、物理和力學參數如阻尼系數、傳導系數、磨擦系數、材料的彈性模量和強度極限等的設計值與製造后和使用中的實際值會有差異，這種差異稱為設計變量和噪聲因素的變差。
  11. ( 6 ) in this paper. adopting fea software ansys to simulation and analysis the al ecap process. in order to spread out studying of ecap in the future. the results show : die comer angle, the radius of round angle, the friction coffience of workpiece and die, the properties of die ( elastic modulus, possion ratio ) et al, have some degree impact on the deformation of materials

    （ 6 ）採用有限元（ fea ）分析軟體ansys對al的擠壓過程進行ecap模擬與分析，為后續研究工作做好鋪墊，分析結果表明：外切角、圓角半徑、試樣與凹模之間的摩擦系數、凹模本身的特性（如彈性模量、泊松比等）等等，對材料的變形量都由不同程度的影響。
  12. The content of this thesis, through the deformation destruction process of th e typical nanlidu landslide along the national highway 318, uses the finite unit a nalysis of computation, revealing the elastic, plastic stress and displacement of each joint inside the slide area pointing out the distribution range of the tension stress and the plastic deformation range, computering the stability safety factor of the slide area, gaining the fixed quantity, quota that evaluates the stability of the slide area, revealing the position of the slide area which is most likely to los e its stability, thus, it can provide theoretic proof for the programs which renova te landslides

    本文的研究內容是通過318國道南里渡典型滑坡的變形破壞過程，採用有限元計算分析，揭示滑體內部每個節點上的彈、塑性應力及位移，找出拉應力分佈區和塑性變形區，計算滑體穩定安全系數，得出衡量滑體穩定的定量指標，揭示滑體最可能失穩的部位，從而為滑坡整治方案提供理論依據。
  13. The thesis built the relation between containing water and the properties of trail dam ' s soil by geomechanical properties of trail dam ' s soil ; analysed the seep rule of water in the trail dam ' s field and the change of soakage line. the thesis applied the limited element to analyze the trail dam of baogang by the engineering item in production. it calculates the dynamic and static response about the dam using the numerical simulation method

    本文通過大量的尾礦土物理力學性質試驗資料，建立了含水量與尾礦土性質之間關系曲線；分析了水在尾礦壩區的滲流規律和不同標高時浸潤線的變化情況，為分析尾礦壩的穩定性提供依據；結合生產上的工程項目，從包鋼尾礦壩的穩定性研究入手，應用有限元法，通過數值模擬分析了水對尾礦壩的靜力、動力穩定性影響。
  14. Besides, this paper adopts the random finite element method, uses geometric and physical mechanical parameters that are relevant to lining weight of surrounding rock, coefficient of lateral pressure, height or buried depth of vertical loading, elastic resistance coefficients of surrounding rock, elastic modulus of support structure, unit weight of concrete, thickness of the structure as well as torsional strength and compression strength of concrete and etc., as random variables, applies the monte - carlo method to sampling by computer, preliminarily evaluates the reliability of bearing capacity and stability of molded concrete lining of the xuefeng mountain tunnel, and obtains the related displacement of the lining, mean value and variance of internal force, and computed the reliability index of lining structures

    此外，本文採用隨機有限元方法，將圍巖容重、側壓力系數、垂直荷載高度或埋深、圍巖的彈性抗力系數、支護結構的彈性模量、混凝土容重、結構的厚度以及混凝土的抗扭與抗壓強度等與襯砌結構有關的幾何與物理力學參數作為隨機變量，應用蒙特卡洛理論進行計算機隨機取樣，對雪峰山隧道模注混凝土襯砌的承載力與穩定性的可靠度進行了初步評估，得出了襯砌的相關位移與內力的均值和方差，並計算出了相應的襯砌結構可靠指標。
  15. A variable is a quantity to which an unlimited number of values can be assigned.

    變量是一個可以有無限數值的量。
  16. In this paper, the finite - element numerical analysis calculation is applied to the foundation of high - rise and multi - floor building and the evolvement law of stress and displacement of tunnel used by urban traffic to explore the mutual influence between the wall rock of underground space and high - rise building foundation, taking account of the specific construction situation in the " sanmu garden " project in dadukou district in chongqing, from the perspective of underground space static - force structure stability analysis to open a underground tunnel with 6m in span and 7. 5m in height for track traffic 20m below the surface. this paper, taking considerations of three different states, i. e. the natural state without any artificial interference, the state of high - rise buildings on the surface, and the underground tunnel state with excavation for track traffic, and four plane lines and four vertical lines, analyzes and studies the distributing law of stress and displacement of calculation section from the following aspects : ( 1 ) the main stress vectorgraph, displacement distribution graph ( ux, uy ) and chromatogram graph of stress isoline ( 1, 2, xy ) of section under different states ; ( 2 ) the contrastive distribution curve of stress ( 1, 2, xy ) of different plane and vertical lines under the same state ; ( 3 ) the contrastive distribution curve of stress ( 1, 2, xy ) of the same plane and vertical lines under different states, wishing to provide references for underground space utilization and project designing and construction of the tunnel under high - rise buildings in the future

    本文結合重慶市大渡口區「三木花園」開發建設項目，從地下空間靜力結構穩定性分析角度出發，針對在該項目中涉及的高層和多層建築物以及在其地下20米處開挖了一個用於軌道交通的跨度6米，高7 . 5米的地下隧道這一具體工程情況，採用2d - 3d -有限元結構分析程序對高層與多層建築物的地基基礎及其與城市軌道交通使用的地下隧道圍巖的應力與位移演變規律進行了有限元數值分析計算，探索了地下空間圍巖與高層或多層建築物地基基礎之間的相互影響，通過考慮未受到任何人為擾動影響的天然狀態、地表存在多層或高層建築物狀態和地下開挖用於軌道交通的地下隧道狀態等三種不同狀態以及4個水平剖線和4個垂直剖線等不同情況，從以下幾個方面具體分析研究了計算斷面的應力與位移分佈規律： （ 1 ）在各種不同狀態下計算斷面的主應力矢量圖、位移分布圖（ ux 、 uy ）以及應力等值線色譜圖（ _ 1 、 _ 2 、 _ （ xy ） ）等； （ 2 ）相同狀態下不同水平與垂直剖線的應力_ 1 、 _ 2和_ （ xy ）對比分佈曲線； （ 3 ）不同狀態下相同水平或垂直剖線的應力_ 1 、 _ 2和_ （ xy ）的對比分佈曲線等，為今後在對地下空間的開發利用以及在高層建築物地下開挖硐室時的工程設計和工程施工提供參考依據。
  17. And the consumption which are caused by the deformation of the rock mass and the consumption which fill all the void space of the joint can be got. then the block coefficient k of the this geologic condition can be got by the actual consumption of the injection grout in the practical grouting

    本論文中主要通過有限元法來計算巖體的變形，並進而求得由巖體變形引起的那部分注漿量和完全充填節理裂隙的注漿量，再根據實際工程的實際注漿量來計算試驗所代表的地層的充填系數k 。
  18. In this article, firstly the background of the textile trade conflicts within sino - us or sino - euro are introduced, thus learn that how to discern and dodge the foreign trade risks, how to choose the appropriate investment projects have already become one of the most important questions for exporting companies on foreign trade affairs well - known as high investment and high risk. so the main text makes a risk analysis qualitatively and quantitatively on a textile - exporting trading company from three angles of statistic 、 game theory and portfolio theory, which is the main content that we studied. firstly, the statistic article adopts data of the transaction closing price of the textile clothing index in shenzhen stock exchange at the end of each quarter as well as several other kinds of data reflecting the macro - economic changes, performs an empirical analysis of these data according to the theory of co - integration test 、 granger cause test and impulse response function of time series in economitric, and learn that the impact to ti is more obvious by the economic index reflecting local commodity price level and economic prosperity degree home and abroad, as well as the impact degree and the time lag degree, and knows the macro - economic risks faced by textile business enterprises ; after that by the game theory angle we analyze exactly the managing risks faced by one textile export corporation named beauty. from the game expansion chart the system arrangement between censor ways by exportation goal countries and exporting strategies by the exporting enterprises has been analyzed. involving the benefit assignment between them both the limited rounds and infinite rounds negotiations of cooperation games have been studied, and then country responsibility and the enterprise managing risks on foreign trade affairs and so on have been analyzed exactly ; in order to realize the investment multiplication in the certain degree to disperse the risk, the

    本文首先介紹了中美、中歐紡織品貿易爭端的來龍去脈，由此可知在涉外貿易這種以高投入、高風險著稱的行業里，如何甄別和規避外貿風險、如何選擇合適的投資項目已經成為外貿企業的首要問題。因此，正文分別從統計學、博弈論和投資組合三種角度對涉外紡織品貿易公司風險進行了定性和定量的分析，這也是本文的主要研究內容。首先，統計學篇選取了深圳證券交易所行業分類指數?紡織服裝指數（ ti ）每一季度末的交易收盤價和若干種反映宏觀經濟變化的指標，利用計量經濟學中時間序列的協整檢驗、 granger因果檢驗和脈沖反應函數等理論做實證分析，從而得知反映國內物價水平和國內外經濟景氣程度的經濟指標對紡織板塊上市值的沖擊比較明顯，且可知沖擊程度和時滯度，進而分析出涉外紡織企業所面臨的宏觀經濟風險;接著，從博弈論的角度具體分析一家紡織品出口公司（ beauty ）的外貿活動所面臨的各種經營風險，該篇從博弈擴展圖入手，分析了出口目的國審查方式與本企業出口策略之間的制度安排;並圍繞雙方的利益分配，研究了有限回合和無限回合合作談判博弈，然後具體論述了國家責任和企業涉外經營風險等問題;在一定程度上為了實現投資多元化來分散風險的目的，投資組合篇從經典的markowitz模型著手，在一些特定條件的限制下，給出了一個相應的投資組合模型。
  19. After simplifying the circuit, it can appear with dynamic planning method system, in order to reduce all expenses of circuit and every corresponding rate of circuit to get every berth to unload. then the short rate of circuit regards linear programming calculation parameter of method as most, thus can make the systematic variable count and reduce them greatly. it is meet with linear programming method various kinds of restrain terms from restrain from and quality system of request overall optimum to get maximum benefit and then

    簡化線路后，可以先用動態規劃方法求出系統中各卸貨點到各泊位之間的所有費用最低的線路和各線路的對應費率；然後將各條最短線路的費率作為線性規劃方法的計算參數，從而使系統的變量數大大減少，再用線性規劃方法求得滿足各種約束條件限制及品質要求的系統總體最優解。
  20. A port tyre crane has various parts and complex structure, which is made up plenty of beam - bar and shell elements, manual calculation can not guarantee the precision while finite element method needs onerous structure modeling and a great deal of date input. the finite element analysis and modeling of the port tyre crane are difficult because of complex structure and various loads. in order to fit further more design and exploitation of the same type as well as the upgrade of the production i study a kind of parametric software for structure analysis of the port tyre crane, it can reduce the difficulty of modeling and structure analysis as well as improve efficiency

    港口輪胎式起重機部件繁多、結構復雜，由數目眾多的梁桿與板殼組成，其結構設計和力學分析使用傳統的手工計算方法難以保證精度，有限元方法則需要繁重的結構建模和大量的數據輸入，並且要求分析人員具有相當的力學知識和有限元基本理論。港口輪胎起重機結構的復雜性、載荷工況的多變性導致港口輪胎起重機結構有限元建模和分析工作效率低、難度大。針對這種情況本課題研發了一套港口輪胎式起重機結構的有限元參數化分析軟體，以適應同類機型的進一步設計開發和產品升級換代，降低建模和分析的工作難度，提高工作效率。
分享友人
分享到 Line

分享到臉書