本壓液體 的英文怎麼說

中文拼音 [běnyāyètǐ]
本壓液體 英文
orthobaric liquid
  • 本 : i 名詞1 （草木的莖或根）stem or root of plants 2 （事物的根源）foundation; origin; basis 3 （本錢...
  • 壓 : 壓構詞成分。
  • 液 : 名詞（液體） liquid; fluid; juice
  • 體 : 體構詞成分。
  • 液體 : liquid; liquor; fluid
  1. Fluid noise mainly comes from out put pulsation of rate of flow, the main reason of out put pulsation of rate of flow is the instant high pressure return flow that obturation cubage produced when the big round curve pressure transition. the v trough on the port plate can reduce the fluid noise. in this paper, the author based on the acting of dam a river and condensability of liquid and used matlab language as tool to calculate the v trough on the original port plate and drew out the p - t diagrammatic curve and analyzed its shortcoming and improved the design of original v trough and got that the best size of its angle was 12. 3 and its length was 5mm and the cross section was an equilateral triangle

    流體噪聲主要來源於輸出流量脈動，造成輸出流量脈動的主要原因是閉死容積在大圓弧段壓力切換時產生的瞬時高壓迴流，在配流盤上開設v型尖槽可降低因高壓迴流而引起的流體噪聲，本文以截流作用和液體的可壓縮性為理論依據，以matlab語言為工具，對原配流盤上的v型尖槽進行了理論計算，繪制出p - t圖線，分析了它的不足，並對原有v型尖槽進行了優化設計，得出了v型尖槽的最佳幾何尺寸：配流盤平面上的v型尖槽的兩邊的夾角為12 . 3 ，槽長5mm ，槽的橫截面為等邊三角形。
  2. The factory is specialized in the manufacture of the whole set of testing equipment fo gas - vase ( do not sew, fuse, liquefied petroleum gas, natural gas etc. spirit bottle ), various air infuses set, remitting to flow row and to infuse tongs ; the stainless steel is four fluorine soft tubes, the industrial air ( the pack ) gathers to pack, modernizing industrial factory premises concentration to provide spirit system and assisting a piece : decompression machine, safe valve, allotment box ; and standard air, hybrid air, special kind air, high install craft device purely and gaseously ; the automation cuts over, going together with to compare to equip automatically ; various air valve door and accessories, spirit bottle enclosure ; the low temperature equipments liquid pump ; vaporize a machine ; the low temperature closes valve ; the ripples takes care of to wait a series product

    本廠專業設計生產製造各種氣瓶檢驗成套設備（無縫，溶解，乙炔，液化石油氣，天然氣等氣瓶） ，各種氣體充灌臺，匯流排及充灌夾具;不銹鋼四氟軟管，工業氣體（充裝）集裝箱，現代化工業廠房集中供氣系統及輔件:減壓器，安全閥，分配箱;以及標準氣體，混合氣體，特種氣體，高純氣體的配置工藝裝置;自動化切換，自動配比裝置;各種氣體閥門及配件，氣瓶附件;低溫設備液體泵;汽化器;低溫截止閥;波紋管等系列產品
  3. It can filter gear oil, hydraulic oil, compressor oil, mechanical oil, spindle oil, turbine oil and insulation oil in deep level

    本機能對輪油液壓油壓縮機油機械油錠子油絕緣油透平油以及一切具有潤滑功能的液體油作深層過濾。
  4. The age hardening characteristic of as - cast cu20ni20mn and cu20ni35mn alloys and the interface characteristic between the alloy and cast tungsten carbide were studied, and on the basis of this study, composites of cu - ni - mn alloy reinforced with different volume fraction ( 0 - 45vol. % ) and different size ( 42 - 362 m ) of cast tungsten carbide particles were made by vacuum hot - pressing liquid sintering technology. pin on disk two body abrasion tests have been performed with different size of sic abrasive under different loads

    本文研究了鑄態cu20ni20mn和cu20ni35mn合金的時效硬化特性及其與鑄造碳化鎢的界面特性，並在此基礎上以不同尺寸（ 42 362 m ）的鑄造碳化鎢顆粒為增強體，採用真空熱壓液相燒結技術制備了不同顆粒含量（ 0 45vol . ）的鑄造碳化鎢顆粒增強cu - ni - mn合金基復合材料；以不同粒度的sic為磨料，在不同載荷條件下利用銷?盤磨損試驗機測試了復合材料的二體磨料磨損性能。
  5. Laser, ultrasonic beam and microwave are used in non contacting level measuring systems. laser systems suffer from dirt, ultrasonic sensors are strongly affected by changes of the velocity of sound and usually a pipe is needed to couple the ultrasonic waves into the liquid tank, which is difficult when there is a high pressure or when explosion protection is necessary

    壓力式液位測量系統原理簡單、成本低，但測量精度和應用場合有一定的局限性，超聲液位儀精度較高，但設備復雜，一般需要用導管將超聲波傳到被測的液體中，因而安裝維護較麻煩，激光測距系統對環境要求嚴格。
  6. Some conclusions can be drawn from the experiment. first, the discharge coefficient of liquid is almost constant when the pressure before injecting is high enough, but the discharge coefficient of gas fluctuates because of the influence of liquid flowing. second, when the total pressure of gas is low, under the same total pressure, increasing the pressure before injecting or under the same the pressure before injecting, lowing the total pressure of gas make the mean diameter smaller

    流量特性試驗表明，在液體噴注壓降較高時，液體的流量系數基本不變，但是氣體的流量系數受液體流動的影響較大;霧化特性試驗表明，在同一氣體總壓條件下，增大液體噴注壓降或者在相同液體噴注壓降條件下，減小氣體總壓對液滴霧化有利。
  7. When pump is applied force downward and moves, the lower check valve is closed, the fluid in the pump is extruded and charges upward out of upper check valve, then flows into upper pump chamber, because that the piston has volume, some fluid flow out of outlet due to the reduce of spatial fluid volume in upper pump chamber

    當泵的柱塞受力向下移動時，下止回閥關閉，泵中的液體受擠壓而向上沖開上止回閥而流入上泵室中，由於柱塞本身佔有體積，部分的流體因上泵室內空間流體積的減少而自出口端流出。
  8. The cold fog is produced by a special device ( cold fogger ) that breaks up the chemical into microscopic droplets by mechanical means, basically with a high - pressure pump and an extreme fine nozzle

    （冷噴霧器）製造。基本來說，此裝置用高壓泵和極細的噴嘴，以機械方法把化學液體變成微細的霧滴。
  9. In the third chapter, the mathematical models of project system have been established, and simulation has been done on the simulink enviroment of matlab software kits. the simulation focus on the effects of main parameters on the dynamic characteristics of speed control system, and the main parameters include viscosity damp coefficient and friction torque of electrical motor shaft, internal leakage coefficient of pump / motor of hydraulic circuits, gas volume of pressure accumulator, viscosity damp coefficient of cylinder piston and different running building floors, etc. at last, theoretical research effects of the flow and pressure pulsation of pump / motor on car speed and oil volume leakage theory are discussed. the fourth chapter of this thesis concerns the research on the key items about hydraulic power control system according to the ens 1 - 2 and other hydraulic elevator standards

    論文第三章針對組成系統的各個模塊進行了機理建模，並且通過matlab軟體中的simulink圖形化模擬環境進行了本課題系統的模擬研究，主要針對影響系統特性的主要參數變化，動態分析系統的輸出特性，在上下行工況中，分析了電機軸系粘性阻尼系數、軸系摩擦力矩、主迴路蓄能器迴路液壓泵馬達內泄漏系數、蓄能器氣體容積、液壓缸柱塞粘性阻尼摩擦系數以及不同運行樓層工況等參數對系統特性的影響；最後對軸向柱塞泵馬達的流量壓力脈動對電梯轎廂速度的影響和蓄能器內油液體積損失機理進行了理論研究。
  10. In this paper, the author demonstrated the basic principle, development history and characters of high - press liquid - enveloped czochralski method ( leg ), and its application in producing the gap semi - conductors, at the same time of introducing the general situation of them

    本文論述了高壓液封直拉法的基本原理、發展歷史、特點，該法在半導體材料行業的應用及應用中的影響因素，化合物半導體材料磷化鎵的概況、高壓液封直拉法在制備該材料時的應用。
  11. The last part of the article discussed briefly the composing of hardware and software of the distributed control system in the glass furnace

    最後，本文簡單介紹了系統的硬體實現及窯壓、液面及燃燒系統等環節的控制策略。
  12. The performance of liquid dmfc is evaluated as a function of the composition and structure of meas, hot - pressing condition and activation process by means of v - i polarization and ac impedance spectrometry

    本研究採用電流電壓極化曲線和交流阻抗譜方法，對膜電極的熱壓條件、擴散層和催化劑層的組成與結構、電極活化過程等因素對液體進料dmfc性能的影響進行了全面的研究。
  13. In the paper, the influence of the westphal ' s pheonmenon of the movement of the pump valve and the compressibility of the liquid on the continuous flow condition of liquid in the cylinder being not only comprehensively considered, but also the dynamic property of the pump valve being reserched, a new accurate dynamic model used to describing movement of the pump valve is set up

    本文綜合考慮了液體可壓縮性、泵閥運動的魏氏效應對泵筒內液體連續流條件的影響，並考慮了泵閥運動的動力特性，建立了新的泵閥精確運動微分方程，該數學模型不存在奇點問題。
  14. To remedy the disadvantages of conventional pneumatic servo system, pneumatic - hydraulic - combination - control ( phcc ) servo system is put forward, where the liquid medium is led into the conventional pneumatic servo system and controlled in closed - loop simultaneously

    摘要為從根本上克服常規氣壓伺服系統的缺點，將液體介質引入到氣壓伺服系統中，並對氣、液進行閉環控制，從而構成了一種氣、液復合介質控制系統氣液聯控伺服系統。
  15. Aiming at the essential defect of pneumatic medium, pneumatic hydraulic combination control ( phcc ) servo system is formed, in which the liquid medium with low compressibility and high viscosity is introduced into a normal pneumatic servo system and is closed - looped controlled simultaneously

    氣液聯控伺服系統正是基於克服或者補償氣體介質的根本缺點，將可壓縮性小、粘度較大的液體介質引入到常規氣壓伺服系統中，並進行控制而構成的一種新型的氣、液介質復合控制系統。
  16. In this thesis the theory and method of intelligent fault diagnosis for a large turbo - pump fed liquid - propellant rocket engine ( lre ) is innovatively proposed and developed, based on the hybrid reasoning strategy and the hybrid knowledge models including mathematical model, logic model, graphic model and qualitative model. the theory and method are constructed in the way of intelligent modeling technique and creative application of knowledge engineering, and focus on the difficult problems and critical techniques such as the unified treatment of lre knowledge ( experience, facts, rules, graph, system structure, behavior, model knowledge and measured data ), the integration and translation of qualitative and quantitative knowledge, and the knowledge - based intelligent fault diagnosis reasoning methods. firstly, besides the correlation of different knowledge, the concept and the types of lre diagnosis knowledge are systematically described

    本文以某大型泵壓式液體火箭發動機為研究對象，以智能建模技術和知識工程的創造性應用為主要技術手段，圍繞著發動機知識（經驗、事實、規則、圖形、結構、行為、模型知識與測量數據信息等）的統一處理技術、定性定量知識的集成與轉化和基於知識的智能故障診斷推理等關鍵技術和難點，創新地研究發展了發動機基於混合知識模型（數學模型、邏輯模型、圖形模型及定性模型）和混合推理策略的智能故障診斷理論和方法。
  17. In this paper, the equilibrium equation of liquid bulge forming small tangential round corner is deduced for the complicated shape tube - type blank, the function equation between forming stress parameters are and the small corner are obtained ; the forming mechanism of the small tangential corner is studied, the matching relation between liquid bulging pressure and axial thrust is given, the optimal liquid bulging force parameters are determined

    摘要本文推導出復雜形狀管類件復合液壓脹形時環向小圓角成形的平衡方程，得出了成形應力與環向圓角半徑的解析關系；研究了環向小圓角成形機理，確定了液體脹形壓力與軸向推力的匹配關系以及最佳的成形力參量。
  18. Wideplus - 9 series pressure transmitter established a model of new price - performance ratio for civil and industrial product of mass low cost. these products are widely adapted for the detection in gas pressure, liquid pressure and even bad medium environment such as pollution water, lightly corrosive liquid and gas

    Wide plus - 9系列壓力變送器為大批量低成本民用及工業產品建立了新的性能價格比典範，本系列產品廣泛適用於對氣壓，液壓的檢測，甚至較惡劣的介質環境如污水輕度腐蝕性液體和氣體。
  19. It shields the vessel against eruptions of methane gas and pressurized fluids and allows for the secure retrieval of nine - meter - long core samples

    這個裝置不但可預防船隻受到甲烷氣體與高壓液體噴發的傷害，也使得每次加深九公尺探採的巖心樣本可安全的回收。
  20. Taking the hydrostatic equilibrium of axial force of pump dm360 as the example, this paper elaborates design calculation and dynamic - static characteristic analysis of hydrostatic bearing with twisting plate throttle, derives design parameters and formulas of bearing structure, discusses effects of various main factors ( oil viscosity, compressibility, distortion coefficient of twisting plate, pressure of oil source, and bearing clearance ) on dynamic characteristic, and obtains some conclusions about the application of hydrostatic bearing in engineering practice

    本文以dm360型泵軸向力的液體靜壓支承平衡為例，對扭板節流靜壓支承的設計計算和動靜態特性分析進行了較為詳盡的闡述，推導出支承結構的設計參數和公式，討論了各種主要因素（油液的粘度、油液的可壓縮性、扭板變形系數、供油壓力、支承間隙）對支承動態特性的影響，給出了一些結論。
分享友人
分享到 Line

分享到臉書