析出液 的英文怎麼說

First, a simple discussion for the mechanism about electrostatic atomization of the liquids has been given ; then the paper theoretically analyzed waving course, liquid drop producing course, and the liquid drop diffusing course in electrostatics atomization process., gave an analysis about the methods about carrying charges to the liquid drop, and analyzed that liquid with high electrical conductivity can be carried charges and atomized by electric field, while the isolated liquid with low electrical conductivity can be charged fully with the soakage electrode and inducing charge methods. at last the paper designed and configured the experimental equipment, conducted the atomization experiment to the three liquid medium - kerosene, emulsifier and alcohol under the same environment, handled the experimental results, then summarized the relationship between liquid electrostatic atomization effect and liquid surface tension, electronic conductivity and viscosity, along with the influence of voltage to electrostatic atomization and so on, found out the liquid atomization rule in high voltage electrostatic field

首先，對液體介質的靜電霧化機理作了初步的探討，理論上分析了液體霧化過程中射流區、波紋區、霧滴區和霧滴擴散區;然後對液體荷電方法進行了研究分析，對于高電導率的液體，場致荷電和接觸荷電可以使其霧化，而對于電導率較低的絕緣液體，需用浸潤電極荷電和感應荷電方法使其充分帶電;最後，根據前面的研究分析，設計和組裝試驗裝置，在同一環境下對煤油、乳化劑、酒精三種不同液體介質進行高壓靜電霧化試驗，並對試驗結果進行分析處理，總結出液體靜電霧化與液體表面張力、電導率和粘度的關系及電壓對液體靜電霧化的影響等，得出高壓靜電場中液體霧化的一般規律。

Nitrosoguanidine crystallizes when the solution is cooled to 0℃.

當萃取液冷卻至0時，亞硝基胍結晶析出。

Hydrogen evolution is always a possibility in water solutions.

水溶液中氫的析出永遠是可能的。

Liberation of hydrogen gas would be increased rapidly and sic particles on the surface might be dispersed if the current density exceed the upper limit. furthermore, nickelous hydroxide would be deposited because the ph of plating solution nearby the surface rapidly increased. all of above might result in coating deterioration

若電流密度過大，超過所允許的上限值，會析出大量的氫氣，可能沖散表面覆蓋的sic微粒，而且易使磨頭表面鍍液ph值急劇上升而形成氫氧化鎳沉澱，導致鍍層質量惡化。

It is stirred with 10%sodium carbonate solution(50ml)and then with water (50ml), after which it solidifies.

與10碳酸鈉溶液（50毫升）混合攪拌，然後再用50毫升水混合攪拌，從而析出固體。

Dead oil in a semi-oxidized state seems capable of effecting the direct precipitation of uranium from solute.

半氧化狀態的重油似乎可能影響鈾從溶液中的直接沉澱析出。

It is suitable for medium such as water, gas, heat energy, crystal and powder material etc, especially suitable for medium of easy sedimentation, fouling, crystal, lumber, mixed with foreign impurity, sewage and medium with corrodibility, high scouring and great friction

適用於水、氣、熱能、漿液、晶粒、粉狀物料等介質，特別是能滿足兩相流溶液工藝流程中易沉澱、結垢、結晶、析出、雜物、異物混雜的介質、污水及腐蝕性、高沖刷性、琢磨性強的特殊需求。

In order to improve the utilization efficiency of energy and equipment, a general steady simulation model of complex cross - feed multi - effect evaporation was established for the purpose of in - depth research on rule of multi - effect evaporation. in this model, the energy - saving measures, including extra steam being led off to preheat material liquid, the condensation water flash and solution flash, were adopted, and the solid separation was also considered in the process of evaporation

為了提高多效蒸發系統能量與設備的利用效率以及深入研究多效蒸發過程的規律，建立了帶有冷凝水閃蒸、溶液閃蒸和引出額外蒸汽預熱原料液等節能措施並考慮蒸發過程有固相析出的復雜錯流多效蒸發穩態模擬通用模型。

The gold recovery machine mainly according to electroplate cathode to adsorb principle, filter inside with the precious metal recovery that the french patent design, it will need the valid metals resolution in the recovery liquid to come out, attain thus to the precious metal material of the recovery make use of, let up to electroplate to discard precious metal in liquid to run off, and lower the purpose of the production cost

金回收機主要是根據電鍍陰極吸附原理，再用法國專利設計的貴金屬回收濾芯，將待回收液中的有效金屬解析出來，從而達到對貴金屬物質的回收利用的作用，減小電鍍廢液中貴金屬的流失，以及降低生產成本的目的。

The autonomous underwater vehicle which carries liquid oxidizer and liquid incendiary agent and uses the outside seawater as coolant request the oxidizer 、 incendiary agent and coolant can supply the power system according to accurate proportion and reasonable flow on any condition. the system should have small volume and light weight and should be easily realized. the system and control mode introduced in this article can fit these requirements well

控制或降低液壓系統油液的污染度和提高液壓元件的污染耐受能力是確保液壓系統可靠工作的兩個重要方面，本文分析了液壓柱塞泵所在系統油液污染特性一定時影響泵污染耐受能力的諸多因素，指出了在結構形式確定的條件下設計高污染耐受度液壓柱塞泵所要求的摩擦副材料與主要表面工藝

Based on the analysis of the driving theory of tft - lcd and the characteristic of lvds interface, we designed a drive circuit to control the horizontal / vertical synchronization signals and pixel signal, this drive circuit has a lvds interface. we make and debug the drive circuit by using performance - to - price fpga ep1c3t144 and lvds transmitting chip ds90c387

在深入分析了液晶顯示器驅動原理和lvds介面特性的基礎上，基於fpga設計了控制顯示器行/場同步信號和顯示像素信號輸出lvds介面的驅動電路，並採用高性價比的fpga晶元ep1c3t144和lvds發送器晶元ds90c387製作和調試了相應的電路。

The pump wheels, turbine wheels, and stators generated by the different blade parameter profiles were compared and the fundamental law of the converter performance versus the blade angle profile was derived

通過對不同參數變化規律生成的泵輪、渦輪、導輪的葉型進行對比分析，總結出液力變矩器葉片角變化對液力變矩器性能影響的基本規律。

The urea - formaldehyde ( uf ) polymer / sio2 composite microspheres were prepared by polymerization - induced colloid aggregation ( pica ) method. the formation mechanism of composite microspheres is attributed to the fact that that urea and formaldehyde firstly undergo acid - catalyzed polymerization to form oligomers, and then the sol particles are adsorbed on the chain of oligomers by wan der walls force and hydrogen bonding. when the oligomers reach the critical chain length, they separate from solution due to phase separation

對復合微球形成機理的研究表明，尿素和甲醛在酸性條件下自身聚合可以形成高分子微球，在sio _ 2酸性溶膠中發生聚和反應時，隨著反應的進行，齊聚物不斷生成， sio _ 2膠體顆粒逐漸吸附在齊聚物分子鏈上，當聚合物鏈達到沉澱臨界鏈長時，由於相分離作用，從前驅物溶液中析出，同時sio _ 2膠體顆粒均勻的分佈在脲醛聚合物網路中，隨之沉澱出來，形成脲醛sio _ 2復合微球。

Analysed the power matching principle of a hydraulic excavator, advanced saving energy control planning which could obtain stable rotating speed of the engine by controlling the flow of every running of pump, the aim was for attaining saving energy

摘要分析了液壓挖掘機功率匹配原則，提出了通過控制泵的排量穩定發動機轉速，以實現以節能為目的的模糊控制策略。

The weight gain greatly increased and approached the theoretical value by the addition of naoh that increased the ph value of solution. the composite powders with compact and continuous silver coating layer were produced

微米玻璃微珠的化學鍍銀，添加naoh提升鍍液的ph值，粉體增重大大提升，銀的最大析出量接近於理論的析出值。

Yellow or yellowish - brown liquid. sediment can be seen after long time storage or refrigeration

本品為黃色或黃褐色液體；長久貯存或冷凍後有沉澱析出。

Description yellow or yellowish - brown liquid. sediment can be seen after long time storage or refrigeration

本品為黃色或黃褐色液體；長久貯存或冷凍後有沉澱析出。

This text completely and systematically studies the status and the development of the pyrolysis and the fluidization of biomass, which distill the bio - oil in the domestic and international area, as well as the existing problems. this thesis primarily include following aspects : ( l ), by experimenting and measuring the energy ( heat value ) and the content of c, h, n chemical element of right 20 kinds of common biomass, on the base of the experimental result, and respectively established the biomass energy predict experiment formula with the element of h and c is from change, and passed the ro. os examination, which provides the basis and convenience for flash pyrolysis fluidization device energy to convert the rate to compute with biomass energy utilization calculation ; ( 2 ), proceeded the tg and dtg experimentation equal velocity ( 10 ? / min, 20 ? / min, 40 ? / min, 60 ? / min ) heating and constant temperature heating by studying on eight kinds of biomass samples, according to the experimental data and arrhenius formula, we established the dynamics model of pyrolysis of, then, using the goast - redfern and p function, we also solved the dynamics parameters and analyze out every kind of biomass ' s frequency factor and parameters of activation energy, and established the every kind of dynamics model of pyrolysis of biomass, all of these provide the theories and basis to make sure the reactor ' s flash pyrolysis work temperature scope design and the describing of pyrolysis reactor dynamics ; ( 3 ), in order to study and ascertain the process of heat completely getting to pyrolysis time of varied size biomass particles, we observed and measured the ratio of length and diameter ( l / d ) with the varied biomass through electron microscope, we concluded the l / d ratios usually is from 5. 0 to 6. 0, the average is 5. 3 ; ( 4 ), we studied the process of biomass transiting and the theory of complete pyrolysis time with the theory of complicated heat field, we got the time ( t ) of the varied size biomass particles arriving to complete pyrolysis, and we knew that the complete pyrolysis time and the time which get to the biggest production ratio are identical, all of these studies provide the theory base for design and forecasting the flash pyrolysis reactor solid state resort time ; ( 5 ), according to the above experiment result, synthesize to make use of the engineering the mechanics, engineering the material, machine the design to learn the principle, deduce, establish the theory of rotation cone flash pyrolysis reactor material resort time ( t ) and reasonable rotation velocity ( or frequency ) relation theory ; and ( 6 ), we gave the reactor ' s smallest cone angle certain, reactor cone wall strength design theory, the reactor production ability theory, the power design method and the critical rotation velocity theory

本文較全面、系統地綜述了國內外生物質熱解液化制取生物燃油技術研究發展現狀及存在的問題，主要研究內容有： （ 1 ）實驗、測定了20種常見生物質的能量（發熱量）和c 、 h 、 n元素含量，根據實驗結果分別建立了以h和c為自變量的生物質能量預測經驗公式，並通過r _ （ 0 . 05 ）檢驗；為閃速熱解液化裝置能量轉化率計算和生物質能量利用率計算提供了依據和方便； （ 2 ）選擇了8種生物質試樣作了等加熱速率（ 10 min 、 20 min 、 40 min 、 60 min ）和恆溫加熱的tg和dtg實驗，根據實驗數據和阿倫尼烏斯公式建立了生物質熱解反應動力學微分方程，並採用goast - redfem積分法和p函數對其動力學參數進行了求解，解析出各種生物質的頻率因子和活化能參數，進而建立了各種生物質的熱解動力學模型，為科學確定反應器的閃速熱解工作溫度范圍及熱解反應動力學描述，提供了理論和依據； （ 3 ）為研究和確定不同尺度的生物質顆粒中心達到全熱解的時間，在體視顯微鏡下對不同粒度的生物質顆粒的長徑比進行了實驗觀察和測定，得出生物質的長徑比（ l d ）一般在5 . 0 6 . 0之間，平均為5 . 3的結果； （ 4 ）採用復雜溫度場傳熱學理論對生物質傳熱過程及充分熱解時間理論進行了研究，解析推導出了不同尺寸生物質顆粒中心溫度達到充分熱解溫度的時間（ t ） ，得出了理論推導的充分熱解時間與最大產油率的熱解時間相一致的結果，為閃速熱解反應器固相滯留時間設計和預測提供了理論依據； （ 5 ）根據上述實驗結果，綜合運用工程力學、工程材料、機械設計學原理，推導、建立了轉錐式閃速熱解反應器物料滯留時間（ ）與轉速（或頻率）合理匹配理論； （ 6 ）提出了轉錐式閃速熱解反應器的最小錐角設計、錐壁強度設計、生產能力設計理論和功率計算方法及臨界轉速理論等。

Chapter five introduces the detail technics process of synthesis of carbon nanotubes by using liquid - hydrocarbon diffusion flame. chapter six discusses and analyzes the effects of every technics paramenters on the nanotubes produced by using liquid - hydrocarbon diffusion flame. chapter seven analyzes the sem and tem micro - appearances of the nanotubes produced by liquid - hydrocarbon diffusion flame and draws the conclusion of the nanotubes " cluster growth mechanism. chapter eight analyzes the sem and tem micro - appearances of the nanofibes produced by liquid - hydrocarbon diffusion flame, and considers that the growth mechanism of nanotubes and nanofibers is different

第六章討論和分析了液態碳氫化合物燃料擴散火焰法制備碳納米管時具體各項工藝參數的影響。第七章分析了擴散火焰法制備碳納米管的sem形貌和tem形貌，歸納出碳納米管團簇生長的規律。第八章對六種基板材料在擴散火焰中制備出的碳納米纖維的sem形貌和tem形貌作了分析討論，認為擴散火焰法制備碳納米管和碳納米纖維的形成機理不同。

Because of the effect of sip porous skeleton, the primary si and the eutectic si were separated on the surface of sip porous skeleton under slow cooling conditions, and there were no typical eutectic microstructures in the al - alloys phase of the composites. 6

處于si相顆粒間隙的過共晶al - si合金液在緩慢冷卻凝固時，初晶si和共晶si會附著在si多孔體骨架上析出，在最終的復合材料中沒有典型的al - si共晶組織。