樣機模型 的英文怎麼說

中文拼音 [yàngjīmóxíng]
樣機模型 英文
prototype model
  • 樣 : Ⅰ名詞1. （形狀） appearance; shape 2. （樣品） sample; model; pattern Ⅱ量詞（表示事物的種類） kind; type
  • 機 : machineengine
  • 模 : 模名詞1. （模子） mould; pattern; matrix 2. （姓氏） a surname
  • 模型 : 1 （仿製實物） model; pattern 2 （制砂型的工具） mould; pattern3 （模子） model set; mould patter...
  1. Finally, the coupling of its forward and sideward motion revises the existing motion curves, in order to ensure that the robot can walk stably enough

    結合機器人物理樣機模型，利用三步規劃法規劃機器人行走步態，使其在平行步態下實現靜態步行。
  2. Finally, in consideration of the characteristics of the differential balance mechanism, a more accurate virtual prototype of the mechanism is established and the simulation is carried out in the software environment of adams. the angular velocity curves of the relevant parts and the natural frequency of the mechanism are got. the results may be helpful to the improvement and the application of the mechanism

    最後，綜合考慮了輪齒嚙合剛度、搖臂軸扭轉柔性及齒輪傳動回差對差動平衡機構的影響，建立了能夠比較完整地反映該機構動態特性的虛擬樣機模型;在adams軟體環境下，對差動平衡機構的虛擬樣機模型進行了動態模擬，得出了能反映該機構動態特性的關系曲線，並確定了其固有頻率，為該機構的改進及其在月球車上的實際應用提供了參考依據。
  3. According to the construction and dimension of the robot arm, this paper constructs a model which skew - rpyr wrist model joined to redundant arm

    根據機器人手臂的結構和尺寸，在機械動力學軟體「 adams 」的模擬環境下，建立冗餘度手臂和斜四關節手腕連接的虛擬樣機模型。
  4. In the virtual environment, it establishes prototyping of hydraulic system, realizes interfacing experiment data of hydraulic system and mechanism system in the same interface and accomplishes the simulating design of virtual prototyping entire system of carne

    在虛擬環境中建立液壓系統的樣機模型，實現液壓系統與機械繫統在同一窗口界面中的試驗數據介面，完成起重機虛擬樣機整機系統的虛擬模擬運行的設計。
  5. Thirdly, the 3d model of the mechanism was established from the results of mechanism optimization by using solidwbrks and the kinematical simulation was carried out on the support of cosmos / motion environment so that the rationality of the optimized parameters and the kinematical curves could be proved

    再次，根據機構尺度優化綜合優化得到的機構參數，採用solidworks軟體對菱形傳動機構熱氣機進行三維建模，在cosmos motion環境中，對熱氣機虛擬樣機模型進行運動及動力模擬，以檢測優化參數和運動規律的合理性。
  6. The first part mainly deals with established overall framework of the intelligent system for manipulator. the second part settles the dynamical model and dynamical simulation of the system. the last part touches on the design of the control system of the intelligent system

    根據82mm自動追擊炮的總體技術要求提出了智能化供彈系統的總體方案，建立了智能化供彈系統的原理樣機模型，並對其進行了運動學分析，解決了智能化供彈系統的運動學正、逆問題，給出了軌跡規劃后的運動規律。
  7. Utilizing the dynamics analytical software adams of mechanical system, the virtual prototyping model of sway downward paper feeding mechanical was established and a simulation analysis was carried out

    摘要利用機械繫統動力學分析軟體adams ，建立了下擺式遞紙機構的虛擬樣機模型，並進行了模擬分析。
  8. This paper includes : on the basis of ty160c bulldozer made in tianjin construction machinery works, completing the design and intensity verifying of dgsy - 25 pipe crane ; using high - grade 3 - dimensional plotting software ug ( unigraphics ) to sculpt ; using adams ( automatic dynamic analysis of mechanical systems ) to establish virtual prototyping model and do dynamic simulation, and verifying the feasibility of this design precept and provide the basis for trial - manufacture of physical prototyping. at the same time, still simulating all kinds of danger operating mode in the course of production, which provides the theoretical foundation for rationally selecting ballast type to prevent the occurrence of overturn accidents

    本文在天津建築機械廠生產的ty160c推土機的基礎上，完成了dgsy - 25型吊管機的改裝設計及強度校核；使用三維實體建模軟體ug建立了模型；使用機械繫統運動學/動力學模擬軟體adams建立了液壓? ?機械一體化的虛擬樣機模型，並進行了動力學模擬，驗證了設計方案的可行性及結構設計的正確性，為物理樣機的製造提供了參數依據；對生產作業過程中的各種危險工況進行了模擬分析，為科學地選用配重類型以防止傾覆事故的發生提供了理論依據。
  9. Firstly, a simplified model of the robot is established in solidworks, which is imported into the simulation software adams. and then the motion curves got from matlab are applied on joints control

    在solidworks中建立機器人的簡化模型，導入模擬軟體adams中，再利用matlab中得到的運動曲線控制虛擬樣機模型的關節運動。
  10. In order to carry on kinematics simulation, ug was used to model the robot, and inputs the robot prototype into adams through the interface between ug and adams

    基於三維參數化軟體ug建立了壁虎機器人的簡化實體模型，然後通過adams與建模軟體的介面，將虛擬樣機模型輸入到adams中去。
  11. The configuration of american six - wheel - rocker - bogie rover is studied. its virtual prototype is created, simulated and optimized using adams. the optimal parameters are obtained

    基於此模型，分析六輪搖臂月球車的結構特點，在adams中建立典型的虛擬樣機模型，進行模擬分析和優化，得到優化參數。
  12. The suspension, wheel and bodywork modules are built with the ideas of parameterization and modularization. the typical virtual prototype is also built up, simulated and optimized using adams

    並運用參數化、模塊化的思想，提取出懸架、輪系和車體模塊，建立典型的虛擬樣機模型，在adams中進行模擬分析和結構優化。
  13. Pack all circuits and each part into prototype, examine the rationality of the structure design, experience the product, carry on the last adjustment, reduce the risk of the mould design

    將全部電路和各個零件裝入樣機模型，檢驗結構設計的合理性，體驗設計產品的使用感受，對出現的問題進行最後的調整，降低模具開發的風險。
  14. Preliminary imply the on orbit running of the coarse - grained virtual prototype of space station. ( 5 ) simulation of the coarse - grained virtual prototype of space station, a ideally result has been obtained

    初步實現了空間站正常的在軌運行； （ 5 ）進行了空間站粗粒度虛擬樣機模型在軌運行的模擬，得到了比較理想的計算結果。
  15. This article optimizes the mechanism and establish the model of new type internal - combustion engine based on virtual prototyping technology according to the demand of the mechanism with double connecting rods and crankshafts

    本文根據新型雙連桿雙曲軸內燃機的開發要求，以虛擬樣機技術為基礎，對雙連桿雙曲軸運動機構設計方案進行模擬優化，建立了新型內燃機的虛擬樣機模型。
  16. In part, according to the basic principles of structure character, the paper sets up dynamics model of humanoid robot, as a guiding theory of virtual protot - ype research, proposes essential parameter of setting up virtual prototype model, including kinematics parameter, mass property parameter, mechanics character - istic parameter and external parameter, etc ; by utilizing pro / e set up threedimen - sional prototype model, carries on kinematics model prove among adams at the same time, finishes dynamics simulation about virtual prototype walking on line and turning utilizing adams finally

    論文的第三部分根據結構特性建立了仿人機器人動力學數學模型，提出了建立虛擬樣機模型的必要參數，包括運動學參數、質量特性參數、力學特性參數和外界參數等;並利用pro / e建立了三維樣機模型，然後在adams中進行運動學模型驗證;最後在adams中對虛擬樣機模型進行了直線行走過程的動力學模擬。
  17. According to the result of the design and the machine parameters, by proengineer the research establishes the simulative sample of rice seeding thrower, inspecting the physics property of the machine such as the assemblage, intervention and weight, and building the 3d imitative models, which can clear show the entity of rice seeding thrower

    根據設計結果和確定的參數，進行機構的結構設計，利用pro engineer建立拋秧機虛擬樣機模型，並檢查機構的裝配、干涉和重量等物理特性，產生的三維實體模型可以直觀的展現拋秧機的模型。
  18. Finally with the software adams, the chassis model with new suspension was built to perform dynamic simulation to forecast the performance. and the simulation result shows that the project of suspension is acceptable. in this paper traditional analysis method and advanced technology were both used to solve the task

    本論文將傳統運動分析方法、計算機三維造型技術和先進的虛擬樣機技術結合使用，發揮各自所長：傳統分析方法用於方案的初步分析和部件的結構設計，計算機三維造型技術和虛擬樣機技術用於建立虛擬樣機模型進行模擬分析。
  19. In order to generally analyze the performance of the horizontal directional drill ( hdd ), several subsystem models, e. g. mechanical subsystem model, hydraulic subsystem model, strength model and control subsystem model are built and integrated into a whole virtual hdd model through parameter associations

    摘要為了全面分析水平定向鉆的性能，針對不同領域，分別建立了機械、液壓、強度和控制等子系統模型，通過參數關聯形成了一個完整一致的水平定向鉆整機虛擬樣機模型。
  20. By the use of virtual prototype technique of adams software to build the virtual prototype model of lifting mechanism of tipper, and to carry out simulation and optimization upon its motion, thus obtains the optimal arrangement scheme to the position of lifting mechanism

    摘要介紹了利用adams軟體的虛擬樣機技術，建立自卸車舉升機構的虛擬樣機模型；並對其進行運動模擬及優化，從而得到舉升機構位呈的最佳布里方案。
分享友人
分享到 Line

分享到臉書