橫向花紋 的英文怎麼說
中文拼音 [héngxiànghuāwén]
橫向花紋
英文
bar-type pattern- 橫 : 橫形容詞1. （蠻橫; 兇暴） harsh and unreasonable; perverse 2. （不吉利的; 意外的） unexpected
- 花 : Ⅰ名詞1 （種子植物的有性繁殖器官） flower; blossom; bloom 2 （可供觀賞的植物） flower 3 （形狀像花...
- 紋 : 名詞（花紋; 紋縷兒） lines; veins; grain
- 橫向 : broadwise; infeed; crossrange; abeam;transverse; transverse direction; cross; crosswise; lateral;...
- 花紋 : decorative pattern; figure; arabesquitic
-
At the surface of the pollen grains there are three types of aperturates, including three porates type, three colpates type and three porate - colpates type ; and four types of sculpture, namely, reticulate, striate, striate - reticulate and verrucate. the upper epidermal cells of the leaves of 12 species plants are detected with hpias - 1000 image analytic system through the treatment of binarization, and the experimental methods are proved stable. the results indicated that the waviness of the anticlinal walls ( sfc ) and the ratio of the feret ' s diameter ( slf ) of the epidermal cells of the middle lamina in the third node of leaves starting from the lowerest part of the stem have a relative constant range and could distinguish from each other. oieanolic acid, l, 5, 8 - trihydroxy - 3 - methoxyxanthone and swertiamarin are separately detected on the tlc, and the different chromatogram of various plants can be considered as characters of identification. the contents of oleanolic acid in 12 species of plants are determinated by hplc, but among the different plants and botanical organs their contents are different, and the highest content in flowers
本文對川鄂產獐牙菜屬藥用植物資源進行了野外調查、標本採集和鑒定，對12種乾燥藥材的性狀進行了描述，提供了可以鑒別的特徵。通過掃描電子顯微鏡觀察的12種本屬藥用植物的花粉粒均為單粒花粉，萌發孔有3孔型， 3溝型和3孔溝型三種類型；表面紋飾包括網狀紋，條狀?網狀紋，條狀紋和瘤狀紋四種類型。用hpias ? 1000高清晰度彩色病理圖文分析系統對葉片上表皮細胞作圖像分析，並進行方法學研究，結果表明，同種植物莖上第3節葉片中段主脈和第1側脈之間葉上表皮細胞垂周壁彎曲程度sfc值和細胞縱、橫向直徑的比值slf值，種間有顯著差異，每種都有相對恆定范圍值。Lateral pattern contributes to shock - resistance dimension stability and durability, suits for long - distance high - speed loadong riding
橫向花紋，具有良好的抗沖擊性和經久耐用的牢固胎體，適合於高載荷行駛。Various successive partial plastic forming methods for processing groove, including thread rolling, cross rolling and skew rolling, splitting, rolling of spline shaft, split rolling, open - die extrusion of spline shaft / gear, extrusion of internal screwed tooth socket parts with large helical pitch, integral cold forging for slot commutator, extrusion - ploughing for outside fin tube, drawing of tube with spiral internal / external ribs etc. have been introduced briefly
摘要介紹了用於加工槽的各種連續局部塑性成形方法，包括螺紋軋制、橫軋與斜軋、分劈、花鍵軸滾軋、劈分軋制、花鍵軸齒輪開模擠壓、花鍵套擠壓、槽型換向器整體冷鍛、外翅片管擠壓一犁削、內外螺紋管拉拔等。
分享友人