氣泡模式 的英文怎麼說

中文拼音 [qìpāomóshì]
氣泡模式 英文
bubble model
  • 氣 : Ⅰ名詞1 （氣體） gas 2 （空氣） air 3 （氣息） breath 4 （自然界冷熱陰晴等現象） weather 5 （氣味...
  • 泡 : 泡Ⅰ名詞1 （氣泡） bubble 2 （像泡一樣的東西） sth shaped like a bubble Ⅱ動詞1 （較長時間地放在液...
  • 模 : 模名詞1. （模子） mould; pattern; matrix 2. （姓氏） a surname
  • 式 : 名詞1 （樣式） type; style 2 （格式） pattern; form 3 （儀式; 典禮） ceremony; ritual 4 （自然科...
  • 氣泡 : air bubble; bubble; bubble cell; pin hole
  • 模式 : model; mode; pattern; type; schema
  1. In all kinds of switches, thermo - optical switch, mems switch, liquid - crystal switch and air bladder switch are the trend of large - scale switch array, and lithium niobate electro - optical switches and electro - optical polymer switches are the trend of fast switches

    在各種光開關中，熱光開關列陣、微機械光開關列陣、液晶光開關以及氣泡式光開關列陣由於集成度較大，因而將是大規模陣列光開關的發展方向。
  2. According to dynamical characteristic of the bubble motion in the flow field, and under the assumptions of isothermal system without interior heat source, uniform bubble size, and ignoring surface tension, the mathematical expressions for interfacial momentum exchanges have been deduced which include drag, virtual mass force, and lift

    針對氣液泡狀流中氣泡運動力學特性，在系統絕熱、無內熱源、忽略表面張力、氣泡尺寸均一前提下建立了氣液相間曳力、虛質量力、升力的數學模型表達式。
  3. Mushy pvc ( dop + additives ) - beater ( stir well ) - vacuuming ( materiel has been completely dewatered and debubbled after vacuuming ) or mix with color paste which has been processed by ball mill and then dropped into mould cavity by needle cylinder ) - solidified in the constant temperature box ( color fixing ) - input basic material - sent to the constant temperature box in the flowing way and then forming and then forming and sent out automatically - cooled by fan - finished products

    糊狀pvc （增塑劑dop +助劑- - -打漿機攪拌均勻- - -抽真空處理） （真空機處理后的物料已完全脫離水分和氣泡）或球磨機處理后的色漿混合後用針筒滴入模具形腔- - -放入恆溫箱中固化（色彩定形） - - -注入底料- - -流水式送入恆溫機，定型后自動送出- - -風扇冷卻- - -成品
  4. Mechanical ventilation with lower tidal volumes and positive end - expiratory pressure prevents alveolar coagulation in patients without lung injury

    採用低潮氣量和呼氣末正壓通氣的機械通氣模式能夠防止非肺損傷患者的肺泡凝固。
  5. Simulations of 2d and two - phase flow in a bubble column and an internal airlift loop reactor

    鼓泡塔與氣流內循環式反應器內兩相流模擬
  6. Based on theoretical analysis, microbubble drag reduction is due to structure change of turbulent boundary layer caused by the microbubbles. experiments testify microbubble drag reduction for turbulent boundary layer, as well as bubble size, main flow velocity, etc. affecting the reduction ; with proper flow field model, turbulent model and difference scheme, numerical methods simulate the effect of boundary layer and bubble numbers on dray reduction

    理論分析提出微氣泡降阻機理在於其引起湍流邊界層結構的變化；實驗證明了微氣泡對湍流邊界層的降阻作用以及氣泡尺度、主流速度等對降阻作用的影響；數值方法利用適當的流場模型、湍流模型和差分格式，模擬邊界層和氣泡數等對降阻的影響。
  7. By employing cole ' s classical theory of bubble dynamics, the motion of bubble produced by the underwater explosion and the corresponding bubble pulsating pressure are calculated. a profile function of the shock wave and its parameters are determined according to the principle of wave profile similitude and the equality of impulses. finally an analytic formula is derived to simulate the whole time history of the pressure from the front shock wave to the bubble pulsation, representing the fluid loadings of the underwater explosion

    木文首先應用庫爾的經典水下爆炸氣泡運動理論計算出氣泡的運動和脈動的壓力波形，再依據波形相似的原則尋找波形模擬函數，用沖量相等的原則確定波形參數，得出了從沖擊波到氣泡脈動壓力整個過程對水下爆炸載荷進行模擬的解析公式。
  8. For the laser stream cleaning, the removing force is qualified by setting up a model, in which laser heats the medium film and produces bubbles in a film of medium near substrate surface, then the growing bubble impels the medium around it, at last the particles on the surface are removed by the rapidly moving medium

    然後引入氣泡成長動力學和流體沖擊力學理論，解釋了激光濕式清洗中微粒被去除的機理，建立了激光濕式清洗光學基片的動力學模型。試驗的結果與模型分析的結論都表明激光濕式清洗能夠有效去除表面吸附的微米甚至亞微米級的污染微粒。
  9. In the text applying the theory of two - phase flow ' press - drop and diversion - phase model, having a analysis to the press characterize of the important part namely the bubble pump of the no - pump libr absorption air - condition, and set up the relational mathematical model

    本文對無泵溴化鋰吸收式空調器的關鍵部位，氣泡泵的特性按照流體力學兩相流的理論進行了分析研究，並應用兩相流的分相模型，建立了數學模型，並進行了數值模擬計算。
分享友人
分享到 Line

分享到臉書