浮動槽 的英文怎麼說
中文拼音 [fúdòngcáo]
浮動槽
英文
float tank-
" the central groove shows that the tail of the animal was not buoyed up or supported by water and striations on the side of the groove show that motion was jerky
他說： 「中間的凹槽顯示，這只水蝎的尾巴並沒有浮起來或者被水支撐著而凹槽旁邊的一些條痕則說明，它運動得並不平穩。To avoid the serious electromagnetic interferer, the analog signals are transformed to frequency pulses which are transferred to the kernel of the system. in the measure of the groove voltage, the method of float - ground is adopted to avoid the high common signal and the range switch circuit is designed to solve the conflict of the wide dynamic range and the high precision. least square curvefit is adopted to reduce the system error
鋁電解生產現場電磁干擾非常嚴重，為此我們將需要測量的模擬信號就近轉換為頻率脈沖后再傳送到控制核心；採用浮地接入方式消除槽電壓信號中的共模成分；設計了量程自動切換電路以解決槽電壓的動態范圍寬和測量精度高的矛盾；用最小二乘法進行曲線擬和以降低測量的系統誤差。Model xjq has following features ： （ 1 ） dummy bottom is adopted, making the recycling capacity of the recycling cylinder is 2. 5times of the tand. ( 2 ) the stator is a cylinder in structure with its inner wall being vertically ribbed, and slots are placed, leading to better cutting lffect to the slurry. ( 3 ) due to low immerging depth of the rotator, low rurning speed of the impeller, and wide space between the impeller and stator, wearing is low and power consumption greatly reduced. ( 4 ) it is spontaneously aerated
Xjq型浮選機為仿維姆科型，該機主要有以下幾個特點： （ 1 ）採用了假底，循環簡可使循環量達到槽容積的2 . 5倍; （ 2 ）定子結構為圓筒型，內壁設有立筋條和長孔，對礦漿的前切作用好; （ 3 ）轉子浸沒深度淺，葉輪轉速低，葉輪和定子間隙大，所以其磨損輕，動力消耗大大減少; （ 4 ）可自吸空氣。Based on the analytic analysis of the linear synchronous motor ’ s layered model, the paper deducted the composing of air gap magnetic fields and the analytic expression of levitating and advancing force. these results provide theoretic guidance not only for the analysis and measurement of the vehicle ’ s air - gap magnetic fields but also for the eatablishment of the
採用各向異性介質近似模擬齒槽區域，並引入定子和轉子等效電流層的概念，建立了直線同步電機的磁場分層模型，在此基礎上得到了氣隙磁場的組成以及懸浮力和推力的解析表達式，為氣隙磁場的分析和測量以及列車運動情況下電磁力軟測量模型的建立提供了理論指導。This thesis researches on the stability of fibre suspensions applying theoretical, numerical and experimental methods. first the linear stability analysis is performed to fibre suspensions utilizing flow stability, slender - body and orientation tensor theories. the governing equations of channel and pipe suspensions of different stability handling modes and tensor closure approximations are derived
首先綜合應用流體動力穩定性理論、細長體理論以及纖維方向張量工具，對纖維懸浮流進行線性穩定性分析，推導槽流和管流的穩定性方程，並對槽流導出在不同的穩定性分析模式以及不同的方向張量封閉格式下的多種形式方程。Qualitative and quantitative measurements of disturbances in channel suspensions are carried out using dye emission and piv techniques
然後採用染色線流動顯示技術與粒子圖像測速技術對槽流懸浮流的擾動波特性進行定性和定量觀測。Floating type metallic and non - metallic fluid power piston rings, groove dimensions for
浮式金屬和非金屬流體動力活塞環凹槽尺寸分享友人