準向位置 的英文怎麼說
中文拼音 [zhǔnxiàngwèizhì]
準向位置
英文
boresight location-
In this paper, ackerman steering linkage of double - wishbone suspension is taken as the study object, choosing the splitting joint and steering lever joint to carry out the design of optimization the mathematics models are established based on the multi - body system dynamics, applying its analysis method of kinematics to study the mechanism kinetic principles owing to more spatial factors considered, and calling off many hypotheses affecting the accuracy, compared with the traditional methods, the models are better to reflect the realistic motion principles, the results are more exact and applicable moreover, the force analysis is applied to the conduct mechanism the analysis method of dynamics in the multi - body dynamics is applied to study the forces applied on every component, working out the constraint reaction force of up and down ball joints, and developing the current computation program in the end, produce the upper wishbone geometry model in the ansys software package, meshing and carrying out the fea, testifying if the intensity of the wishbone meet with the requirements
本文以雙橫臂獨立懸架的轉向傳動機構作為研究對象，選擇對斷開點和節臂球銷的位置進行優化設計，在此基礎上建立了基於多體系統動力學的導向機構和轉向傳動機構的數學模型，運用該學科的運動學分析方法研究機構的運動規律，編制了通用優化設計軟體。由於考慮了更多的空間因素，取消許多影響準確性的假設，因此建立的數學模型與傳統的方法相比更能反映實際運動規律，得到的優化結果也更加精確實用。此外，本文還針對導向機構進行受力分析，在建立該機構的空間動力學模型后，運用多體動力學中的動力學分析方法研究各個桿件的受力，計算出上下球鉸的約束反力，並開發出了相應的通用計算程序。By comparing the results with relative experiment data, it is shown that rng k - is more exactly than the other turbulent model. 2 ) the influences of axial inflow position, radial outflow size, rotating reynold number, non - dimensional mass flowrate and axial inflow angle on the flow and heat transfer characteristics were numerically investigated for a typical rotator - stator cavity with axial inflow, radial inflow and radial outflow. the correlations for average nusselt number vs rotating reynold number or non - dimensional mass flowrate were established
（ 2 ）針對一典型的徑向、軸向進氣，徑向出氣的轉-靜盤腔結構，系統研究軸向進氣位置、徑向出口大小、旋轉雷諾數、無量綱質量流量和軸向垂直預旋進氣等對盤腔內流動和換熱的影響，整理出轉-靜盤腔內轉盤平均努謝爾數與旋轉雷諾數無量綱質量流量之間的準則關聯式。Due to the short distance among the planes which fly in a group, the conventional low resolution radar can not distinguish them in both distance and azimuth ? if we use the technology of isar to resolve the difference among doppler frequency of the targets and obtain a fine resolution cross - cross image, we may separate them, but a long time of coherent processing is needed <, for the formation targets, it can be approximately divided to rigid body and nonrigid body, so for the formation targets, that can be regarded as rigid which has a relative position and an identical movement, can be approximately considered as a large target, and be compensated by translational phase with the rule of minimum entropy, but for the most those cannot accord with the approximation of rigid, being the doppler - frequency of the aim is linear changed, by the relax method with short data, increases the resolving performance of multiple target to the aim in the frequency domain, since cross - range resolution is based on the accumulative time, so it is greatly improve the resolution to formation targets by the instant cross - range image which produced by radon - wigner transformation
低分辨isan成像及干涉技術應用研究一因此直接無法分辨編隊目標的架數，我們借鑒isar的技術，通過較長時間的相干積累，在多普勒頻域上對目標進行分辨。而對于編隊目標，可分為近似剛性的多目標和非剛性的多目標，所以對于可以近似為剛體的編隊目標相對位置固定，運動方式一致，可以近似看作一個大目標，採用最小墑準則對平動相位的進行補償，但是大多數並不滿足剛體近似的編隊目標，由於目標在相干積累時間的多普勒頻率近似呈線性變化，通過對較短數據利用relax的時頻分析方法，提高了頻率域上目標分辨的性能。由於橫向解析度取塊于橫向積累時間，所以利用radnwigner變換得到瞬時的一維橫向距離像大大提高了對編隊目標的分辨，對模擬和實測數據的大量分析結果表明此方法的有效性和可行。When used to surface geochemical exploration, it can predict and judge the position and properties of the transverse profile of the oil - gas horizon ; when employed to borehole geochemical exploration, it can accurately predict and judge the position and properties of the longitudinal profile of the oil - gas horizon based on the composition and content of the light hydrocarbon
運用於地表化探，預測與判斷油氣層的橫向剖面位置與性質；運用於井中化探，利用輕烴的組成和含量上的特徵可準確預測與判斷油氣層的縱向剖面位置與性質。This paper, based on normalizing well logging data while drilling and correcting depth into true vertical depth and calculating reservoir parameters and etc, combining the practical ease of mobei oilfield, extracted logging and geological pattern characteristic of target oil - gas formation and geosteering mark formation, and used bp neural network and regressive analysis to create predicting mode of geosteering parameter to build relevant contrast curve ; adopted geometry geosteering method to fix on die drilling direction of bit upper and declination, the position in reservoir, to judge the real drilling case. all finely solved the problem to follow the geological target while drilling for three horizontal well these methods improve the drilling horizontal well ability by using the techniques to follow the geological target while drilling, and then it is convenient and practicable
本文在開展隨鉆測井資料的標準化和斜井校正及儲層參數解釋與含流體性質判釋等工作的基礎上，結合研究工區莫北油田的實際情況，提取了目標油（氣）層和導向標志層的測井地質模式特徵，並採用bp神經網路法和回歸分析法建立了地質導向參數的預測模型、構造了相應的對比曲線；採用幾何導向法確定鉆頭上下傾鉆進方向及其在目標層的位置，以判斷實際鉆進地層情況，很好地解決了研究工區三口水平井的隨鉆跟蹤地質目標的問題。When it arrives at the predetermined destination, the robot controls multi - putting - ball mechanisms and puts the game - ball into the drum simultaneously. on the other side, on the basis of the theory and experiment, we subjoin a line - tracking device in the robot system, ensuring the correct moving of the robot along the white index line on the venue, in order to increase the accuracy of orientation. during the automatic moving, the robot measures the position on the venue by itself, moreover, judging its direction and automatic cut - away with the single - chip microcomputer. this system has been finished the experiment, and find credibility, be in point
同時，為了保證機器人正確地沿著比賽場地上的指示線行走，提高機器人定位的準確性，還從理論和實驗的角度，在機器人上增加了一套尋線系統，以便機器人在其自動行走的過程中，隨時檢測自身的位置狀態，判斷偏離方向，進行自動的糾正。這一套尋線系統已完成了實驗，且比較可靠、適用。The instrument can easily and correctly location, depth of the underground pipes and the exact position of leak points on the insulating anticorrosive coating without digging ground
本儀器不挖開復土的情況下，方便而準確地查出地下管道的走向、深度和絕緣防腐層的漏蝕點的精確位置，使整個管道表面不再屢遭到處開搪破土之苦。Using the complex potential method in the plane theory of elasticity of an anisotropic body, a series solution to the stress field of a finite plate containing multiple cracks subjected to arbitrary loads is obtained by means of the faber series expansion, and the stress intensity factors at the crack tips are calculated based on the theories of fracture mechanics. equivalence yield stress is introduced in order to consider the effects of the plastic zones, with which the strip yield criteria is developed in the article so that the effects of structural size and the crack interactions on the stress distribution can be considered accurately. the effects of plate size, crack size and crack distributions on the stress intensity factors as well as the residual strength of the plate are studied detailedly
採用各向異性體平面彈性理論中的復勢方法，以faber級數為工具，得到了含多裂紋有限大板在任意載荷作用下應力場的級數解，並應用斷裂力學方法確定裂紋尖端的應力強度因子；引入當量屈服應力考慮裂尖塑性區的影響，提出基於帶屈服準則的剩餘強度分析模型，能夠充分考慮結構尺寸和裂紋之間相互作用對應力場的影響；通過數值計算詳細討論了結構尺寸和裂紋之間位置關系對應力強度因子和結構剩餘強度的影響規律，得到了一系列對工程應用具有實用價值的結論。In order to better detect the image edge information, firstly, non ? linear median filter technology of characteristic direction was applied to filter out the gauss noise ; secondly, ( 3, 1 ) biorthogonal spline wavelet was used as the primitive wavelet filter, adopting lifting scheme to build the most superior biorthogonal wavelet filter, and applying the superior biorthogonal wavelet to the multiresolution wavelet edge detection ; at the same time, floating threshold was defined and applied to the image edge detection, and the image edge position was located accurately
在激光探測系統中，微弱的回波圖像淹沒在強背景噪聲中，為更好地檢測這類含噪圖像的邊緣信息，首先應用特徵方向非線性中值濾波技術，濾去高斯噪聲；其次，選擇（ 3 ， 1 ）雙正交樣條小波作為原始小波濾波器，採用提升方案構造最優雙正交小波濾波器，應用構造的雙正交小波進行多尺度小波邊緣檢測；同時，通過定義浮動閾值，並應用於圖像邊緣檢測，較準確地定位了邊緣位置。In order to better detect the image edge information, firstly, non - linear median filter technology of characteristic direction was applied to filter out the gauss noise ; secondly, ( 3, 1 ) biorthogonal spline wavelet was used as the primitive wavelet filter, adopting lifting scheme to build the most superior biorthogonal wavelet filters and applying the superior biorthogonal wavelet to the multiresolution wavelet edge detection ; at the same time, floating threshold was defined and applied to the image edge detection, and the image edge position was located accurately
在激光探測系統中，微弱的回波圖像淹沒在強背景噪聲中，為更好地檢測這類含噪圖像的邊緣信息，首先應用特徵方向非線性中值濾波技術，濾去高斯噪聲；其次，選擇（ 3 ， 1 ）雙正交樣條小波作為原始小波濾波器，採用提升方案構造最優雙正交小波濾波器，應用構造的雙正交小波進行多尺度小波邊緣檢測；同時，通過定義浮動閾值，並應用於圖像邊緣檢測，較準確地定位了邊緣位置。Heavy duty pressure gauges, with diaphragm system to din 14 421 for fire - fighting pumps, nominal sizes nd 80, connection position bottom, radialor back, central
膜片重載壓力表，符合din 14 421 ，用於消防水泵，標準尺寸表徑80 ，介面位置底部徑向或背後正中。Heavy duty pressure gauges, with diaphragm system according to din 14 421 for fire - fighting pumps, nominal sizes nd 80, connection position bottom, radial or back, central
膜片重載壓力表，符合din 14 421 ，用於消防水泵，標準尺寸表徑80 ，介面位置底部徑向或背後正中。Send the real - time position, velocity of the moving object. received by gps oem caxd, associaied with the status information of the vehicle devices, to the monitoring centef, by way of the mobile conununication network. the monitoring system, based on some gis software, displays the tracks of the mobile objects on the eiectronic map, and users could supervise and query their iaterested parameters such as the location or velocity of the vehicle, the general information of vehicles, as so on, so that provide bases for vehicle management, improve the efficiency, or assure vehicles against accidents
車輛監控系統是its的重要組成部分之一，它將全球衛星定位技術、地理信息技術（ gis ）和現代通信技術結合在一起，通過將裝有gps接收機的移動目標的動態位置、速度、狀態等信息，實時地通過無線通訊鏈路傳送至監控中心，在具有強大的地理信息查詢功能的電子地圖上進行移動目標運動軌跡的顯示，並可以對目標的準確位置、速度、運動方向、車輛狀態等用戶感興趣的參數進行監控和查詢，為調度管理提供可視化依據，提高車輛的運營效率，確保車輛安全。Heavy duty pressure gauges with bourdon tube, nominal sizes nd 80, connection position bottom, radial or back
高壓波登管壓力表，標準尺寸表徑80 ，介面位置底部徑向或背後。Heavy duty pressure gauges with bourdon tube, nominal sizes nd 160, connection position bottom, radial or back
高壓波登管壓力表，標準尺寸表徑160 ，介面位置底部徑向或背後。Heavy duty pressure gauges with bourdon tube, nominal sizes nd 100, connection position bottom, radial or back
高壓波登管壓力表，標準尺寸表徑100 ，介面位置底部徑向或背後。Mouse operation, the goal gap at the moment, the middle red line to see the ball in the direction of said location
鼠標操作，對準球門的空擋射門，看中間紅線表示球的方向位置。Introduction : mouse operation, the goal gap at the moment, the middle red line to see the ball in the direction of said location
鼠標操作，對準球門的空擋射門，看中間紅線表示球的方向位置。Defect ? one or more flaws whose aggregate size, shape, orientation, location, or properties do not meet specified acceptance criteria one are rejectable
缺陷?合計的尺寸、形狀、取向、位置或性能不滿足規定的驗收標準的一個或一個以上的傷而被拒收。1 the permit holder shall, not later than 2 weeks before commencement of dredging at the site, submit details on silt curtains to be used, including dimensions, exact locations and method of installation and removal, to the director for approval
許可證持有人須在工地展開挖泥工程至少兩星期前，向署長提交所採用的隔沙網詳情，包括網的大小、準確位置，以及安裝和拆除的方法，待署長批準。分享友人