滑移判據 的英文怎麼說

中文拼音 [gǔyípànjù]
滑移判據 英文
criterion for slip
  • 滑 : Ⅰ形容詞1 （光滑; 滑溜） slippery; smooth 2 （油滑; 狡詐） cunning; crafty; slippery Ⅱ動詞（貼著物...
  • 移 : Ⅰ動詞1. （移動） move; remove; shift 2. （改變; 變動） change; alter Ⅱ名詞（姓氏） a surname
  • 判 : Ⅰ動詞1 （分開; 分辨） distinguish; discriminate 2 （評定） judge; decide 3 （判決） sentence; con...
  • 據 : 據Ⅰ動詞1 （占據） occupy; seize 2 （憑借; 依靠） rely on; depend on Ⅱ介詞（按照; 依據） according...
  1. Through the excel program, and combining the inside and outside environment of the excavation and stress field and displace field, the data of stress and displacement of points are analyzed in variable depth and load grade and terminal state. the spss software has been applied to the statistics of geometry parameter of failure surface, and the failure surface criterion is created by the linearity regression from d ( the longest horizontal distance between the failure surface and the side face of the slope ), ho ( the depth

    此外，應用spss軟體對試驗破壞滑弧的幾何參數進行統計分析，並對滑弧的最大水平深入距離d及d處至坑底的高度h _ 0結合各水理指標進行多元線性回歸，建立滑面的判據，並對此判據進行修正，且用實際工程對其進行評價，通過反算已知滑面的c 、值，表明邊界條件對破壞形式有極大的干擾作用，所直接看到的破壞類型土體不是發生整體滑移破壞，而是剝落式的潰屈破壞。
  2. This paper is based on the working theory of anti - lock braking system, the properties of fuzzy control, the modelling for vehicle system and vhicle tyre. by using of wheel speed sensor, the gather of wheel speed is practiced by filter, amplier, modifying of wheel speed. based on the wheel slip ratio of abs. given vehicle speed and wheel speed, the wheel slip ratio is computed. the error and error change ratio of slip ratio is obtained by given refering slip ratio. which is the input of fuzzy control which comprises of input fuzzy

    本文根據防抱死制動系統的工作原理，模糊控制的性能特點，車輛系統模型及車輪輪胎模型，利用輪速傳感器，對輪速進行濾波、放大、整形等實現了車輪速度的採集。採用基於車輪滑移率的防抱控制理論，根據車速、輪速來計算車輪滑移率。由參考滑移率計算出滑移率的誤差、誤差變化率並作為控制器的輸入變量完成了模糊控制的模糊化、模糊推理、模糊判決。
  3. Author thinks that the direction of the maximum plastic distortion along a constant radius around the crack tip may be considered as the direction of shear - mode fracture ( named pmax - criterion ) and the load when located shear band prongs the ligament in the front of crack tip is regarded as the limited load of shear - mode fracture. ( 3 ) the fad ( fracture assessment diagram ) of titled crack is proposed based on achievements of mesomechanics about i - ii complex ductile fracture of metal, and the titled crack is classified two kinds : void - mode fracture is assessed by fracture assessment curve, and shear - mode fracture by limited load. ( 4 ) using a fe program based on plantle - ressue theory to calculate some mesomechanical parameters, a flange joint structure of a high pressure vessel ( design pressure 31. 4mpa and the thickness of the hemispherical head is half of that of shell. ) is analyzed to determine whether the structure under operation pressure is safe or not, forecast the mode of potential invalidation and argue for the rationality of design of the structure

    試件的整體斷裂為剪切型，但在試件芯部裂尖鈍化區中部出現了韌窩型啟裂並有一定的擴展，說明局部較高的應力三軸度也會使韌窩型機制得以發展，但是不改變試件整體的剪切型斷裂模式；對韌性斷裂的剪切模式的細觀機理做了一定的探討，並且提出了含裂紋構件剪切型斷裂的宏觀判據：認為裂紋前方的集中剪切帶中與裂紋尖端等半徑處最大有效塑性應變出現的方向可以作為裂紋剪切斷裂的方向（可簡稱為_ （ pmax ）準則） ，集中剪切滑移帶貫穿裂紋前方承載韌帶時的載荷可以作為極限載荷；本文運用金屬韌性斷裂細觀力學在一復合型韌性斷裂方面的研究成果，採用失效評定圖的形式，提出了傾斜裂紋的安全性評定方法的基本框架。
分享友人
分享到 Line

分享到臉書