灰口鑄鐵 的英文怎麼說

中文拼音 [huīkǒuzhùtiě]
灰口鑄鐵 英文
ferrosteel
  • 灰 : Ⅰ名詞1 （物質燃燒后剩下的粉末狀的東西） ash 2 （塵土; 某些粉末狀的東西） dust 3 （特指石灰） lime...
  • 口 : Ⅰ名詞1 （人或動物進飲食的器官; 嘴） mouth 2 （容器通外面的地方） mouth; rim 3 （出入通過的地方） ...
  • 鑄 : Ⅰ動詞（鑄造） cast; coin; make Ⅱ名詞1. （古國名） zhu, a state in the zhou dynasty2. （姓氏） a surname
  • 鐵 : Ⅰ名詞1 （金屬元素） iron （fe） 2 （指刀槍等） arms; weapon 3 （姓氏） a surname Ⅱ形容詞1 （形容...
  • 鑄鐵 : [冶金學]1 （煉鐵） iron casting2 （生鐵） foundry iron; pig; cast iron; c i ; casting pig; foundr...
  1. The particles distributed hi the matrix of grey cast iron, but some contact each other. the composite layer extend gradually into the substrate. when volume fraction of wc is 36 wt % and 27 wt %, the matrix of the composite is high chromium cast iron, consist of white carbide bars and the austenite. wc particles distributed uniformly, retaining approximately quondam granular form in the composite layer which has an evident interface area with the substrate, with good bonding strength

    對不同碳化鎢體積分數的灰鐵和低鉻鑄鐵基復合材料的微觀組織結構分析表明：碳化鎢體積分數為52時，復合層內基體為灰口鑄鐵組織，顆粒直接分佈在灰鐵基體上，部分碳化鎢顆粒有相互接觸的現象，基材與復合層之間沒有明顯的過渡；碳化鎢體積分數為36 、 27時，復合層內基體為高鉻鑄鐵，由面塊狀的奧氏體和白條狀碳化物組成，碳化鎢顆粒表面固溶於基體組織中，粒形基本保持完整，分佈均勻，與基體構成冶金結合，基材與復合層之間存在一個明顯的平緩過渡區。
  2. Founding - grey cast irons ; german version en 1561 : 1997

    鑄造.灰口鑄鐵
  3. Soft mechanical joint grey cast iron pipe

    柔性機械介面灰口鑄鐵管
  4. Founding - grey cast irons

    鑄造.灰口鑄鐵
  5. Founding. grey cast irons

    鑄造.灰口鑄鐵
  6. Grey cast iron

    灰口鑄鐵
  7. After the study on the characteristic of the fatigue behavior of gray cast iron dryer, the fatigue analysis on this kind of dryer is carried out so as to specify the fatigue analysis method of dryers

    本文還在分析灰口鑄鐵烘缸疲勞特性的基礎上，對該烘缸進行疲勞分析，以此說明烘缸疲勞分析設計的方法。
  8. Gray iron castings for pipe fittings

    灰口鑄鐵管件
  9. Gray iron castigs for pipe fittings

    灰口鑄鐵管件
  10. Flanged ductile - iron pipe with ductile - iron or gray - iron threaded flanges

    帶球墨鑄鐵或灰口鑄鐵螺紋法蘭的法蘭球墨鑄鐵管
  11. Gray cast iron valves

    灰口鑄鐵閥
  12. Gray cast iron

    灰口鑄鐵
  13. Depend on the invalidation of the current network ' s statistic ; this thesis selected the gray cast iron pipes as the main object to research

    根據對目前國內管網失效情況的統計，本文確定灰口鑄鐵管管壁強度可靠度作為主要研究對象。
  14. We find that the cast - iron pipe is only mildly corrosive and the indoor pipeline is just rust - eaten, but the seamless steel pipe corrodes badly

    結果表明：主幹線灰口鑄鐵管整體狀況良好，只有局部輕度腐蝕；庭院無縫鋼管腐蝕較嚴重；戶內管道大多存在不同程度的銹蝕。
  15. The effect of the structure of austenite zone on the performance of gray iron welding joint is studied by means of thermo - simulated test in this paper

    摘要採用熱模擬試驗方法探討了灰口鑄鐵焊接接頭熱影響區的奧氏體區組織對接頭性能的影響。
  16. Taking advantage of the abundant local iron ore and coal materials, the iron pipe factory pipe fitting factory and cast iron factory, in order to meet the local market demand, developed products of four series with 300 items. these items are divided into two categories, mainly centrifugal cast iron pipe, pipe fittings, stainless steel joints and clamps, art - enclosure, seamling steel pipes, manhole, covers and balance weight iron

    煉鐵廠鑄管廠和管件廠根據市場需求和當地豐富的優質生鐵煤炭資源優勢，形成一條的生產優勢。開發出四大系列三百多個品種的產品，分灰口鑄鐵和球墨鑄鐵兩大類，主要有離心鑄管管件井蓋配重鐵等。
  17. The calculation method of the utmost load of gray cast iron beam with rectangle section is obtained through the analysis of limit load behavior of the beam under the united action of bending and pulling, therefore the design method of limit load about forcing parts of cast iron pressure vessels is determined

    通過分析灰口鑄鐵矩形截面梁在純彎曲和拉彎組合作用下極限載荷行為，提出灰口鑄鐵矩形截面梁極限載荷的計算方法，由此確定灰口鑄鐵壓力容器受壓元件的極限設計方法。
  18. The main properties of new alcohol based spraying coatings for green sand mold are superior to the abilities of internal and outside coatings of the same kind, the surfaces of castings that are produced used new alcohol based spraying coatings are smooth without adhering sand and gas - hore

    粘土濕型砂鑄造新型醇基噴塗塗料的主要性能達到了國內外同類產品領先水平；生產的高錳鋼、可鍛鑄鐵和灰口鑄鐵產品表面光潔，無粘砂、氣孔等缺陷。
  19. The reinforcing effect has been researched, with wc of 40 ~ 60 mesh dimension and 10 ~ 52 wt % volume fraction. the matrices were grey cast iron and low chromium cast iron

    復合材料中碳化鎢顆粒粒度為40 60目，體積分數范圍為10 52 ，基體材質分別選用了灰口鑄鐵和低鉻鑄鐵，研究了它們的復合效果。
  20. Abstract : based on the study of the stave " breakage mechanism, the maximum thermal stresses are the temperture field and thermal stress of the stave are calculated and studied with developed finite element program. the maximum thermal stresses are compared between ht stave and qt stave, and some improving suggestions for cooling stave design are brought forward

    文摘:在解剖研究取得的對高爐冷卻壁破損機理認識的基礎上，使用開發的有限元程序計算並研究了高爐冷卻壁工作狀態下的溫度場和熱應力分佈，對灰口鑄鐵和球墨鑄鐵兩種冷卻壁材質的最大熱應力進行了分析和比較.據此提出了冷卻壁設計的一些改進性建議
分享友人
分享到 Line

分享到臉書