無心輪磨 的英文怎麼說

中文拼音 [wúxīnlúnmó]
無心輪磨 英文
centerless grinding
  • 無 : 無Ⅰ動詞（沒有） not have; there is not; be without Ⅱ名詞1 （沒有） nothing; nil 2 （姓氏） a surn...
  • 輪 : Ⅰ名1 （輪子） wheel 2 （像輪子的東西） wheel like object; ring; disc 3 （輪船） steamer; steamboa...
  • 磨 : 磨動詞1 （摩擦） rub; wear 2 （研磨） grind; mull; polish 3 （折磨） grind down; wear down [out]:...
  • 無心 : 1 （沒有心思） not be in the mood for 2 （不是故意） not intentionally; unwittingly; inadvertentl...
  1. Centreless grinding wheel

    無心研磨砂輪
  2. This paper introduces an innovative design of m1050 centerless grinding machine which provides automation for feed mechanism, regulation & compensation of wheel & guide wheel and parts inspection in addition, the design principle is also described with a detailed illustration on structure design of the automatics above - mentioned

    摘要介紹了m1050無心磨床自動進給、砂輪、導輪自動修正與補償裝置的改造設計及自動測試裝置的設計，闡述了設計原理，詳細介紹了裝置的結構設計。
  3. Until now, there have been a few reports on the damage of the water pumps caused by sand and water cavitation. by use of the test loop for solid and liquid two phases, under the condition of 3 % head drop, the damage location and relative degree of the sand and water cavitaiton occurred on the impeller were tested and researched. the result was, them, compared with the results under the condition that water cavitation occurred and no cavitation but only wear occurred. the differencts were analyzed. the analysis result can be used as the basis of the further research and the improvement of the impeller shape

    目前含沙水汽蝕對水泵損傷方面的報導甚少，本文利用固液兩相流試驗臺，對離心泵閉式葉輪在含沙水汽蝕時（ 3揚程下降點）的損傷部位和相對程度進行了試驗研究，並將此結果與清水介質發生汽蝕時的損傷情況[ 13 ]及含沙水無汽蝕情況下的磨損情況[ 7 ]相比較，對其差異進行了分析，為今後進一步探討葉輪損傷機理和葉型改進提供了實驗依據。
  4. Put the work on the rollers to realize non - centering grinding by motor, no need to set center before working

    它是一種高精密，無心研磨的電動工具機，沖子只需放于兩滾輪之間，不用校正中心即可加工。
  5. Carbo centreless grinding wheel is mainly grinding outside diameter of workpiece. it is suited for a grinding operation of mass production because of the higher efficiency for a grinding diameter

    無心研磨砂輪主要以工件外緣研磨加工為主，由於所加工外徑效率較高適用大量生產之研磨作業。
  6. Bonded abrasive products - dimensions - part 2 : grinding wheels for centerless external cylindrical grinding

    粘合磨料產品.尺寸.第1部分:無心外圓磨砂輪
分享友人
分享到 Line

分享到臉書