熱因性粘合劑 的英文怎麼說

中文拼音 [rèyīnxìngniángějì]
熱因性粘合劑 英文
resinoid
  • 因 : Ⅰ動詞[書面語] （沿襲） follow; carry on Ⅱ介詞1 [書面語] （憑借; 根據） on the basis of; in accord...
  • 性 : Ⅰ名詞1 （性格） nature; character; disposition 2 （性能; 性質） property; quality 3 （性別） sex ...
  • 粘 : 粘動詞（粘附） glue; stick; paste; adhere to; bond
  • 合 : 合量詞（容量單位） ge, a unit of dry measure for grain （=1 decilitre）
  • 劑 : Ⅰ名詞1 （藥劑; 制劑） a pharmaceutical or other chemical preparation 2 （某些有化學作用的物品） a...
  • 粘合劑 : adhesie cement
  1. The composite has excellent performance of water retaining, that the adsorbed water of 85 % is retained after being dried 10 days at the room temperature, and the adsorbed water of 45 % is retained after being dried 24 hours at 60 the factors influencing on water absorbency for the superabsorbent composite such as the kinds and concentration of starch, clay, crosslinker, initiator, the external salt solution and hydrolysis degree are investigated in this paper

    該超吸水性復合材料在室溫下乾燥10天後的保水率為85 ，在60 2條件下加熱24小時后的保水率為45 。本文較詳盡地探討了超吸水性復合材料的合成條件，並系統地研究了影響超吸水復合材料吸水倍率的各種因素。例如：粘土的種類及粘土的用量、澱粉的種類及澱粉的用量、交聯劑的用量、引發劑的用量、水解度（氫氧化鈉的用量） 、水解時間、外部鹽溶液的種類及濃度等條件。
  2. Using the dynamic mechanical analyzer ( dma ), pdms / pma ipn was investigated at temperature of 5 - 180 c. the initiator, the component ratio, the type of pdms and the filler effected the damping properties. the result showed that the damping ability varied with the parameter and there was an optimal value. the excellent damping material in the papers was ipn, where tan man was 0. 735, and the damping functional temperature ranged with tan 8 > 0. 3 was 46 c. the micro - morphology and structure of pdms / pma ipn were characterized by two kinds of sem

    高分子阻尼材料的有效阻尼功能區是在ipn材料的t _ g區間內，而研究常溫條件下的阻尼性能更具有重要應用價值，運用動態熱機械分析（ dma ）儀對ipn阻尼材料進行表徵，在5 180內對其損耗因子（ tan ）進行研究，發現引發劑和交聯劑的用量、聚硅氧烷的用量和分子量等參數對ipn阻尼性能的影響較大，存在一個合理配比值，當pma與粘度為3300pa ? s的pdms之比（質量比）為1 . 17 ： 1 、交聯劑用量為1時， tan最大值為0 . 735 ，大於0 . 3的溫域差達到46 。
  3. The mechanism of fuel saving and emission reduction were discussed in this paper. based on surface chemistry, proper emulsifiers were selected to produce stable emulsified diesel oil, which contains different amount of water. the characters of emulsified fuel such as viscosity, heat value and factors in connect with stability were analyzed

    本文以利用乳化油減少柴油機燃油耗和降低排氣污染為主要目標，先從理論上分析了乳化油節能和降低排放的機理，然後利用表面化學的知識篩選出適當的表面活性劑，復配出高效的復合型乳化劑並用其配製出不同摻水率的穩定的乳化柴油，對乳化油的物性（粘度、熱值等）及影響乳化油穩定性的因素進行了分析。
  4. Lactide were investigated. the key factors affecting the polymer intrinsic viscosity were found to be monomer recrystallization times, stannous octoate concentration and polymerization time. the thermal stabilizing agent did not significantly affect the polymer molecular weight. the polymer with a viscosity average molecular weight beyond 200000 was fairly reproducible by optimizing the polymerization conditions. it was found that poly

    單體重結晶次數辛酸亞錫濃度聚合時間等條件均是影響聚合物特性粘數的重要因素。熱穩定劑對聚丙交酯的分子量幾乎沒有影響。優化聚合條件可以獲得粘均分子量大於200000的聚丙交酯材料，聚合結果具有良好的重復性。
  5. The conjoint affection of ruo _ 2 power on ta foil is also discussed here, including : selection and ratio of adhesive, selection and ratio of conductive agent, temperature and time of heat - press treatment of electrode. research indicated that temperature and time of heat - press treatment of electrode have the most effect on electrochemical properties of as - produced electrode

    然後討論了粉體與鉭片基體結合的影響因素，包括:粘合劑的選擇和比例、導電劑的選擇和比例、熱壓溫度和時間對電極片的電化學性能的影響，研究表明:熱壓溫度和時間對電極片電化學性能影響較大。
分享友人
分享到 Line

分享到臉書