熱管式冷卻器 的英文怎麼說

中文拼音 [règuǎnshìlěngquèqì]
熱管式冷卻器 英文
heat pipe cooling
  • 管 : Ⅰ名詞1 （管子） pipe; tube 2 （吹奏的樂器） wind musical instrument 3 （形狀似管的電器件） valve;...
  • 式 : 名詞1 （樣式） type; style 2 （格式） pattern; form 3 （儀式; 典禮） ceremony; ritual 4 （自然科...
  • 冷 : Ⅰ形容詞1 （溫度低; 感覺溫度低） cold:冷水 coldwater; 你冷不冷? do you feel cold?; are you feeling...
  • 卻 : Ⅰ動詞1 （後退） step back 2 （使退卻） drive back; repulse 3 （推辭; 拒絕） decline; refuse; reje...
  • 器 : 名詞1. （器具） implement; utensil; ware 2. （器官） organ 3. （度量; 才能） capacity; talent 4. （姓氏） a surname
  • 管式 : tubular管式泵 tubing pump; 管式避雷器 expulsion type arrester; 管式除塵器 pipe precipitator; 管式...
  1. In model zw. the indirect heating still is omitted. the condensor adapts calandria heat exchanger. of course the screw plate heat exchange and coil pipe cooler can also be provided as request. when adapt coil pipe cooler, the buffer tank

    冷凝器採用列管式換熱器，也可根據用戶要求供應螺旋板式換熱器，冷卻器採用盤管式冷卻器，採用盤管式冷卻器並配套供應穩壓罐和比重測定器。
  2. The components of this system are a cross - flow finned - tube evaporator, cross - flow finned - tube gascooler, a reciprocation compressor, a gas - liquid seperator, a double pipe internal heat exchanger and a throttling valve

    系統由一個叉流翅片管式蒸發器、一個叉流翅片管式冷卻器、一臺往復式壓縮機、一個氣液分離器、一個套管式回熱器、一個節流閥組成。
  3. At hot end of beat pipe, several measures were taken to eliminate heat, namely ( 1 ) traditional sensible heat elimination ; ( 2 ) exhaust air is processed by air washer, then passes through hot end ; ( 3 ) exhaust air is handled by wet film, then passes through hot end ; ( 4 ) sprays water at the top of hot end, respectively

    第一級採用熱管式間接蒸發冷卻器，熱端布置4種散熱方式： （ 1 ）傳統類型的顯熱散熱； （ 2 ）排風經過噴水室降溫后進入熱端； （ 3 ）排風經過填料式直接蒸發冷卻器降溫后進入熱端； （ 4 ）直接在熱端頂部淋水。
  4. Of the currently available coolers for electronic products with a high heat flux, microchannel heat sinks have been proved to be able to provide the best heat transfer performance and are one of the most promising coolers. the manifold microchannel ( mmc ) heat sink has many advantages such as low thermal resistance, compact structure, little amount of coolant, low flow rate, uniform temperature distribution along the flow direction and many others, so it is able to provide the best heat transfer performance : lowering the maxmal temperature and the temperature difference

    在目前高熱通量電子產品冷卻器中，微通道熱沉已被證實是傳熱性能最佳且最具應用潛力的冷卻方式之一，而歧管式微通道熱沉因具有低熱阻、結構緊湊、所需冷卻液量小、沿流動方向溫度分佈均勻等優點則成為減小電子元器件換熱表面最高溫度、降低溫度變化的一種有效方法。
  5. The corrugated tank made of high quality cold - rolled - steel sheet manufactured with special production line. it can swell up or shrink compensating the oil from atmosphere. protect and delay the oil and the insulation against degradation, therefore enhance the operation reliability and free of maintenance under normal conditions

    全密封變壓器與普通油浸式變壓器相比，取消了儲油櫃，由波紋油箱的波翅代替油管作為冷卻散熱元件，波紋油箱由優質冷軋薄鋼板在專用生產線上製造，波翅可以隨變壓器油體積的脹縮而脹縮，從而使變壓器內部與大氣隔絕，防止和減緩油層的劣化和絕緣受潮，增強運行可靠性，正常運行免維護。
  6. It is of pipe type used for evaporation, heating, condensing, cooling operations, materials for this unit are optional as per the physical, chemical and corrosive properties

    這是一種管殼式換熱器，可用於蒸發、加熱、冷凝、冷卻等工藝，由介質的物理、化學和腐蝕等性能來選擇適宜的材料製作。
  7. It specifies the process of the design, simulation and experiment of liquid cooling system. main contents of the thesis are as follows : description of the present usage of liquid cooling system, presentation of a new type of liquid cooling system and description of its work principles ; design of the liquid cooling system, which mainly deals with the design and collating calculating of serpentine condenser and heat exchangers adopted in this system. meanwhile, the model chosen calculating of compressor 、 thermal expansion valve 、 plate evaporator 、 water pump and the like equipment used in the system are also carried out

    本文的主要內容如下:對液冷源使用現狀進行了描述，提出了一種新型液冷源系統並對其工作原理進行了闡述;對系統進行了設計，主要對系統中所採用的管帶式冷凝器和水側空/液換熱器進行了設計和校核計算，同時對系統中所用到的壓縮機、熱力膨脹閥、板式蒸發器、水泵等配套設備進行了選型計算;分別對製冷系統和冷卻液循環系統進行了數學建模。
  8. The heat transfer and flow resistance performance of petal - shaped finned tube oil - cooler with helical baffles was studied, and compared the total heat transfer coefficient of petal - shaped fimed tube oil - cooler with helical baffles with that of smooth tube oil - cooler with segmental baffles

    摘要研究了螺旋隔板花瓣管水冷殼管式油冷卻器的傳熱和流阻性能，並與弓形隔板光滑管水冷殼管式油冷卻器進行了性能對比。
  9. The condensation heat - exchange characteristic of a separate - type heat - pipe was studied on a 1 : 1 model. the heat pipe is heated by electricity, and working fluid is distilled water, and it is cooled by air. the experimental results show that, ( 1 ) when charging liquid ratio is 45 %, condensation heat - exchange coefficient reaches to maxium ; ( 2 ) when there is not non - condensing gas, the coeffcient decreases a little with the increase of vapour pressure, and it decreases by 9. 5 % when the pressure increases from 0. 16mpa to 0. 36mpa ; ( 3 ) when there is non - condensing gas, the coefficient decreases a little, but when the gas is discharged by an exhaust value, it can be improved, when the volume content of the gas is 2. 5 %, it can increased by 22 % ; ( 4 ) the effect of the non - condensing gas on the coefficient decreases with the increase of the pressure, and when the volume content of the gas is 5 % and the pressure increases from 0. 16mpa to 0. 36mpa, the coefficient increases by 6 %. the relative curves are given between condensation heat - exchange coefficient and air flowrate, charging liquid ratio and vapour pressure

    建立了空氣冷卻實驗臺，熱管的加熱方式為電加熱，工質為蒸餾水.在1 1模型上對分離式熱管管內凝結換熱特性、不凝性氣體對凝結換熱的影響及不凝性氣體的擴散規律進行了試驗，得出分離式熱管有一最佳充液率，其值為45 %左右；凝結換熱系數隨著蒸汽壓力的增加略有降低，在實驗的壓力范圍內，降低了9 . 5 % ；不凝性氣體對分離式熱管的凝結換熱僅影響冷凝段下部較小部分，通過排氣閥排出不凝性氣體可有效地改善冷凝段下部的凝結換熱；隨著壓力的增加，不凝性氣體對分離式熱管冷凝段的影響減少.這些結論可用於分離式熱管換熱器的工程設計和控制
  10. Abstract : the condensation heat - exchange characteristic of a separate - type heat - pipe was studied on a 1 : 1 model. the heat pipe is heated by electricity, and working fluid is distilled water, and it is cooled by air. the experimental results show that, ( 1 ) when charging liquid ratio is 45 %, condensation heat - exchange coefficient reaches to maxium ; ( 2 ) when there is not non - condensing gas, the coeffcient decreases a little with the increase of vapour pressure, and it decreases by 9. 5 % when the pressure increases from 0. 16mpa to 0. 36mpa ; ( 3 ) when there is non - condensing gas, the coefficient decreases a little, but when the gas is discharged by an exhaust value, it can be improved, when the volume content of the gas is 2. 5 %, it can increased by 22 % ; ( 4 ) the effect of the non - condensing gas on the coefficient decreases with the increase of the pressure, and when the volume content of the gas is 5 % and the pressure increases from 0. 16mpa to 0. 36mpa, the coefficient increases by 6 %. the relative curves are given between condensation heat - exchange coefficient and air flowrate, charging liquid ratio and vapour pressure

    文摘:建立了空氣冷卻實驗臺，熱管的加熱方式為電加熱，工質為蒸餾水.在1 1模型上對分離式熱管管內凝結換熱特性、不凝性氣體對凝結換熱的影響及不凝性氣體的擴散規律進行了試驗，得出分離式熱管有一最佳充液率，其值為45 %左右；凝結換熱系數隨著蒸汽壓力的增加略有降低，在實驗的壓力范圍內，降低了9 . 5 % ；不凝性氣體對分離式熱管的凝結換熱僅影響冷凝段下部較小部分，通過排氣閥排出不凝性氣體可有效地改善冷凝段下部的凝結換熱；隨著壓力的增加，不凝性氣體對分離式熱管冷凝段的影響減少.這些結論可用於分離式熱管換熱器的工程設計和控制
  11. This type of capacitor has an assembling full - sealed structure, and it is comprised of capacitor unit body, contain - er, insulation cooling impregnant, outlet ceramic bushing, pressure - releasing valve and temperature controller etc. the internal insulation cooling impregnant is isolated from external atmosphere so as to avoid aging of impregnant and ingress of moisture

    全密封集合式並聯電容器主要由電容器單元組成的器身波紋油箱絕緣冷卻油出線套管支持絕緣子壓力釋放閥及溫度控制器等部件構成。採用波紋油箱增大散熱面積降低產品溫升。
分享友人
分享到 Line

分享到臉書