熱管式爐 的英文怎麼說
中文拼音 [règuǎnshìlú]
熱管式爐
英文
pyrotube furnace-
The afterheat, which is collected by recovery devices, in winter can be used as the low level thermal source of heat pump, and in summer can preheat feed water, thus equivalent an economizer. because energy flows in the system so reasonably that energy is used to the most, therefore, its energy conservation effect is significant, and the operating expenditure declines consequently. the sewage can be reused after due treatment, thua it has a certain social and ecological benefit, too
本研究中選用分離式熱管裝置提供洗浴用水，利用水源熱泵裝置，一機兩用，進行空間供熱和製冷，並通過余熱回收器對系統內的余熱進行回收，冬季可作為水源熱泵的低位熱源，夏季可對鍋爐給水進行預熱，起到「省煤器」的作用。這樣實現系統內的能量合理流動，從而達到節能的目的，同時洗浴污水經適當的處理后可以回用，因而還具有一定的社會和生態效益。Basic environmental testing procedures. test methods. fire behaviour. analysis and titrations of gases evolved during pyrolysis or combustion of materials used in electrotechnics. exposure to abnormal heat or fire. tube furnace method
基本環境試驗程序.試驗方法.火災特性.氣體在高溫分解過程中的分析和滴定或電工用材料的燃燒.異常熱力或火災輻照.管式爐法We specialize in manufacturing & developing the high efficiency self recuperative gas burners, which are widely used in direct heating and the radiant tube in various industrial heat treatment furnaces
本公司專業生產和開發高效率空氣自身預熱式燒嘴，廣泛應用於各種工業熱處理爐的明火或輻射管加熱Series full - auto pipe expander with drawing device and program interface is used with extruding machine. it is also used solitarily, while expanding pipes, the machine adopts translation, the action is steady and corret, it does not damage pipe materical, the machine adoptes double - infrared heating oven type, each oven is equipped with heating cire, the shaping method adopts expanding - end shaping, the size of pipe mouth is correct. on its panel, there is a transfer swith of expanding solvent type pipe socket ( straigh port ) and expanding sealloop type pipe socket ( rport ). the choice of expanding pipe type is very convenient, the technologocal adaptability is strong, its main electric control elements are all imported. the syetem charecteristics are steady and reliable
配有與主機配套的接料牽引裝置和相應的程序介面，既能與擠管主機聯線使用，又可以作單機使用；擴管時管材的移動均採用平移方式，動作平穩準確而且不易損傷管材；這種機型採用紅外線加熱方式且為雙加熱爐型，每個加熱爐都配有中心加熱爐芯；成型方式均採用擴管頭定型方式，管口成型尺寸準確；該機型在控制面板上設有擴溶劑型承介面（直口）和擴彈性密封圈型承介面（ r口）的轉換開關，擴管方式選擇十分方便，工藝適應性強；主要的電器控制元件均採用進口元件，系統性能穩定可靠。The product of electric furnace fittings including : micro - computer program temperature control instrument 、 refractory brick ( ultra - light weight energy saving brick ) 、 resistance wire 、 electroheat belts 、 electrical heat tube 、 silicon carbide rod 、 furnace bottom plate 、 muffle tank 、 vacuum sealed fan 、 wind wheel 、 axis 、 substructure 、 bin seat 、 flat shape plate 、 box 、 panel 、 weatherstrip plate 、 return air plate 、 bin 、 connection box 、 educe rod 、 thermocouple 、 thyristor 、 porcelain pipe 、 crucible 、 furnace chamber 、 furnace frame 、 charging bin 、 substructure 、 pit furnace cover lifter framework ( sole design ) and otherwise
電爐配件產品包括：微電腦程序控溫儀、耐火磚（超輕質節能磚） 、電阻絲、電阻帶、電熱管、硅碳棒、爐底板、馬弗罐、真空密封風機、風葉、軸、底座、料筐座、扁形板、箱體、面板、擋風板、回風板、料筐、爐柵、接線盒、引出棒、熱電偶、可控硅、瓷管、坩堝、爐膛、爐門、爐框、裝料筐、底座、井式爐蓋升降機構（獨家設計）等。The product adopts the infalling through system on the structure of boiler pipe line, if equips safely valve an will stop working automatically in case hyperthermal, super - pressure and low water lever
安全採用水管貫流式爐膽結構，並配備安全閥，溫度過熱，水位過低，壓力過高等四重保護，絕對安全可靠。High temperature resistant measure is taken to extend its service life significantly in comparing with the tube still hot air furnace, whereas, cross brushing of heat sink by the smoke and negative pressure smoke exhaust are used to ensure a clean heat exchanging position with stable thermal performance
該爐採取了耐高溫措施，從而使其壽命比列管式熱風爐大大延長，並採用了煙氣縱向沖刷散熱片和負壓式排煙方式，換熱部分不積灰塵，無須清理，熱性能穩定。After thermodynamic calculation on several operation conditions of the furnace, cold - state flow and resistance mensuration, the combustion of the tubular - furnace hearth was changed into swirl and addition of radiate cylinder and oxygen content detection minish 1. 25 surplus air to less than 1. 15, improving the combustion condition and convection and radiate heat transfer efficacy, resuling in reducing the waste - gas temperature 45, decreasing exhaust gas loss, and saving fuel by 6 %
摘要通過對加熱爐幾種工況進行熱力計算、冷態試驗的流場分佈及阻力測定和熱態試驗的爐膛溫度場分佈及管壁溫度等參數的測定，確定將管式加熱爐爐膛內直流燃燒改為旋流場燃燒和增加輻射筒，增設煙氣含氧量分析，可以將燃燒的過剩空氣系數從1 . 35減小到1 . 15以下，極好地改善爐膛內的燃燒狀況和對流輻射傳熱效果，從而降低排煙溫度45 ，減少加熱爐排煙損失，節約了煤氣量6 %以上。2. design scheme of gravity heat pipe air pre - heater is proposed which fits the actual situation of injecting steam boilers. detailed heat calculation and design on heat recovery of flue gas is carrying out
提出了採用適合於注汽爐實際工況的重力熱管式空氣預熱器的設計方案，對煙氣的余熱回收進行了詳細的熱力計算和設計。Technical standard for heat resistant steel castings of petrochemical tubular heater
石油化工管式爐耐熱鋼鑄件技術標準Single burner gas - fired overhead radiant - tube heaters. part 1 : safety
單鍋爐燃氣的頂置散熱管式加熱器.第1部分:安全性Calcuation of the thermal efficiency for petrochemical tubular heaters
石油化工管式爐熱效率設計計算The new device consists of paint - drying box, heat carrier boiler, heating pipe, expansion tank, gas separator and oil tank, etc. the data of two applied examples shows that heat carrier paint drying method is able to make painting - drying cost drop by 88 %, compared with the conventional one, that it has some advantages such as uniform temperature field, good appearance and lower costs, compared with conventional hot air convection mode
該裝置主要由熱載體烤漆爐、輻射加熱管，熱載體爐、膨脹器、油氣分離器和儲油槽等組成。應用實例的測試數據表明，與傳統的遠紅外電加熱鋼瓶烤漆方式相比較，鋼瓶熱載體烤漆節能和降低能耗費用十分顯著，能耗費用降幅達到88 。與熱風爐對流烤漆方式相比較，熱載體烤漆方法不僅節能，而且烤漆爐溫度場均勻穩定，同時烤漆的外觀質量也得到了明顯提高。Approchment to the calculation on hydrodynamics of the flag pattern surface on corner tube boiler
角管鍋爐旗式受熱面水動力計算方法探討The object to study in this paper is the electric heat reservoir boiler, which is used to supply heat water and bask for the resident population. the use of the system define the character of the output medium with the lower request on quality and parameter, at the same time, it ask the boiler should has the higher character on the respect of the cost, reliability, economy, and so on. hence, the paper carefully design and study the system for the choice and design of the boiler core heating componet, the lay of the heat exchanger, the working status of the heat reservoir equipment, the adjustment and control mode of to supply heat water. the study work mainly include underside some contents, forexample : 1. to confirm the heat medium parameter to adapt the requirements of the most of the heating equipments and to design the instruction of the boiler and heat reservoir as simple as possible
圍繞上述原則，本文從電熱鍋爐核心加熱元件的選型及設計、換熱面的布置、蓄熱設備的運行工況、供熱的調節方式以及控制方法進行了較細致的研究和計算，具體研究工作有以下幾個方面： 1 .根據使用要求，確定適用於多數採暖設備的熱介質參數，設計在結構型式上盡可能簡單的鍋爐和蓄熱器； 2 .對製造加熱元件電熱管的各種材料進行了對比和分析、在結構尺寸上進行了仔細的分析和計算，根據實際使用條件給出合理的設計，使其具有較高的可靠性和使用壽命； 3 .對不同換熱面布置形式進行傳熱分析。Heat pipe air pre - heater is adopted to recover gas heat to heat up cold air for burning, reducing flue gas temperature and increasing heat efficiency of injecting steam boiler
採用熱管式空氣預熱器，利用排煙熱量加熱冷空氣，降低了煙氣溫度，減少排煙熱損失，提高注汽爐熱效率。Based on the theories of fluid mechanics and heat transfer, a new way of semi - sealing tube combined with a structure of heat disturbing, distributing, and isolating is created
根據流體力學和熱傳導理論，設計了解決這一問題的半封閉式爐管結構氧化方法和相關的勻流隔熱散熱裝置。Engineering specification for heat resistant iron castings of petrochemical tubular fired heater
石油化工管式爐耐熱鑄鐵件工程技術條件The application of heat pipe type water supply preheater in oil field high - pressure direct current boiler
熱管式給水預熱器在油田高壓直流鍋爐上的應用Rubber vulcanized - determination of rubber content - furnace tube pyrolytic method
管式爐熱解法分享友人