熱蝕刻 的英文怎麼說

中文拼音 [rèshíkè]
熱蝕刻 英文
thermal etching
  • 蝕 : Ⅰ動詞1. （損失; 虧耗） lose 2. （腐蝕） erode; corrode Ⅱ名詞（天體現象） eclipse
  • 蝕刻 : [電學] [冶金學] etch; etching
  1. This paper mainly discusses the designing and testing method to the dds acousto - optic mode locking. it also makes some further analysis on the critical technology - - - - - - the transducer acoustical membrane matching and transducer thinning, which can directly affect the performance of acousto - optic elements. it then analyses the heat effect of acousto - optic elements and the technology of transducer thinning by developing ion - beam sputtering of high frequency acousto - optic elements

    本文重點討論了dds聲光鎖模器的設計及測試方法，討論和分析了影響聲光器件性能的關鍵工藝換能器聲學膜層匹配和換能器減薄工藝，對聲光器件的熱效應進行了測試分析，對離子刻蝕法聲光換能器減薄新工藝作了一定的探討。
  2. P - type silicon crystal plates have been adopted in the text, which are formed mask sio2 by heat - oxygenation. and figures are diverted by normal light etching technology

    本文採用p型單晶矽片，由熱氧化形成sio _ 2掩膜層，標準光刻工藝進行圖形轉移，用koh溶液濕法刻蝕製作倒四棱錐腐蝕坑列陣。
  3. By increasing the h2 dilution ratio, it is found that atomic hydrogen can selectively etch amorphous phase and stabilize crystalline phase. from the study on the distance from substrate to catalyzer, choosing a proper distance can ensure the gas fully decomposed, while a relatively low substrate temperature can cause the nanocrystalline particles to lose mobility and keep their sizes. the pre - carbonization process can enhance the nucleation density and make the growth of high quality nanocrystalline p - sic films much easier

    實驗結果表明：隨著工作氣壓的減小，薄膜的晶粒尺寸有所減小；通過提高氫氣稀釋度，利用原子氫在成膜過程中起的刻蝕作用，可以穩定結晶相併去除雜相；選擇適當的熱絲距離能保證反應氣體充分分解，又使襯底具有較高的過冷度，是形成納米薄膜的重要條件；採用分步碳化法可以提高形核密度，有利於獲得高質量的納米- sic薄膜；襯底施加負偏壓可以明顯提高襯底表面的基團的活性，因負偏壓產生的離子轟擊還能造成高的表面缺陷密度，形成更多的形核位置。
  4. Considering the practical manufacturing condition, an oxygen - free copper microchannel heatsink consisting of five copper sheets is designed and fabricated utilizing the technology of deep photolithography, mechanical machining, and bonding with medium

    根據實際製作條件，設計了五層結構微通道熱沉，採用深層光刻分離曝光化學腐蝕技術、機械加工技術和銅直接粘接技術（ dbc ）制備出冷卻大功率半導體激光器迭陣的無氧銅微通道熱沉。
  5. Then based on the principle for pcr, 20 - cycle continuous - flow pcr is designed using cad software. to the designed 20 - cycle continuous - flow pcr chip, a krf excimer laser ( direct write method ) is adopted as the fabrication technology, and the polymethyl methacrylate ( pmma ) is selected as the substrate. so the appearances of pmma surface etched before and after by 248nm excimer laser under different incident fluences are analyzed using sem

    為此在應用掃描電鏡和三維形貌分析儀對pmma表面被準分子激光刻蝕前後的形貌、刻蝕粗糙度以及單脈沖刻蝕率等進行詳細分析的基礎之上，總結出了準分子激光刻蝕pmma的宏觀規律和微觀刻蝕機制，提出了一種準分子激光刻蝕pmma的是光熱光化學以及羽輝共同作用的理論解釋。
  6. The n - type ps ( 80 ? cm - 100 ? cm ) had been immersed in the mixture of amine ( ( c2h5 ) 3n : c2h4 ( nh2 ) 2 = 3 : 2 ) for twenty minutes, then carried on rapid thermal oxidation ( rto ) through a quartz tube and oxidized in a floating oxygen ambience ( 0. 5 l / min ) at the temperature 400 for 30 s

    N型（ 80 - 100 ? cm ）矽片刻蝕后的多孔硅在胺液中浸泡20min ，然後在氧化爐中進行熱退火，退火溫度在400時， o _ 2流量為0 . 5l / min的條件下退火30秒，在紫外燈照射下，所得ps發藍白光。
  7. The work mainly consists of four parts : the first part is to use oxidation and lpcvd technique to produce sio2 mask film and si3n4 insulation film in order to enhance the heating efficiency of micro chamber, and guarantee the carry out of the reaction. the second part is to use the combination of dry etching and wet etching to produce reaction micro chamber, it is the container which carry out the pcr reaction, and dna sample carry out amplification reaction here. the third part is to use the sputtering, photolithography to produce heaters and temperature sensors which heat the reaction micro chamber and provide the temperature condition for the pcr reaction

    首先，利用氧化工藝和lpcvd技術，生長sio _ 2掩膜層和si _ 3n _ 4絕緣層，以提高反應腔的熱效率，保證擴增反應的順利進行；其次，用濕法腐蝕和干法刻蝕相結合的方法加工微型腔體，使之作為dna樣品進行pcr擴增反應的容器；第三，用濺射、光刻等工藝在微型腔體底部製作微型加熱器和溫度傳感器，實現對反應腔體的加熱及其溫度的精確測量，提供pcr擴增反應所需的溫度條件。
  8. It is praised as permanent heat insulating material with no need of renewal because it is not only safe but also durable in rigor condition of low and cryogenic temperature, underground, open air, flammability, moisture sensitivity and even chemical erosion

    它在低溫深冷地下露天易燃易潮以及化學侵蝕等苛刻環境下使用時，不但安全可靠，而且經久耐用，被譽為「不需更換的永久隔熱材料」 。
  9. They have fine high temperature function such as resist erosion etc. can be mainly used at upper part of heat - storing room of glass kilns etc

    該產品具有耐侵蝕等優良的高溫性能，主要用於玻璃窯爐蓄熱室上部，小爐斜旋等使用條件苛刻等部位。
分享友人
分享到 Line

分享到臉書