燃燒速度系數 的英文怎麼說

中文拼音 [ránshāosùdùxìshǔ]
燃燒速度系數 英文
combustion rate coefficient
  • 燃 : 動詞1. （燃燒） burn 2. （引火點著） ignite; light
  • 燒 : Ⅰ動詞1 （使東西著火） burn 2 （加熱或接觸某些化學藥品、放射性物質等使物體起變化） cook; bake; hea...
  • 速 : Ⅰ形容詞（迅速; 快） fast; rapid; quick; speedy Ⅱ名詞1 （速度） speed; velocity 2 （姓氏） a surna...
  • 度 : 度動詞[書面語] （推測; 估計） surmise; estimate
  • 系 : 系動詞（打結; 扣） tie; fasten; do up; button up
  • 數 : 數副詞（屢次） frequently; repeatedly
  • 燃燒 : （物質劇烈氧化而發光、發熱; 燒） burn; kindle; flame; set on fire; [化學] combustion; inflammation; ignition
  • 速度 : 1. [物理學] velocity; speed; blast; bat 2. [音樂] tempo3. （快慢的程度） speed; rate; pace; tempo
  • 系數 : [數學] coefficient; ratio; modulus; quotient; factor
  1. The precondition of establishing mathematics model of torpedo turbine system in design condition is to fulfill the external conditions ( such as torpedo sailing speed and depth etc. ) and inner conditions ( such as turbine power and efficiency etc. ). after establishing mathematics model of torpedo turbine system in design condition, we compiled simulation program to compute all kinds of inner parameters of turbine engine include engine type, principal layout of turbine, inner structure of turbine and state parameters of gases

    首先分析設計工況時渦輪機動力系統，在滿足魚雷動力系統的各項外部條件（如魚雷航深、航速等）和內部條件（如渦輪機功率、效率，燃燒室壓力、溫度，轉子機械強度等）的前提下，建立起設計工況渦輪發動機的數學模型，編程計算並確定渦輪機內部機械結構和燃氣熱力學狀態各參數。
  2. The thesis emphasis the way and arithmetic of the key equipment of walking reheating furnace : loader machine, unloader machine, walking system, series transfer roll, control system of burning and tracking of steel billet, . make use of the system, we can carry out the function of transferring measuring and weighting, detecting, loading and unloading tracking the steel billet, we can control process of burning and exchange data each other to track the steel billet and manage the process over all of product line. goals of reheating furnace ' s producing process such as high yield, low consuming and pollution, automatic operating mode are achieved

    本文著重研究了步進式加熱爐關鍵設備如：裝鋼機、出鋼機、步進梁、爐前爐后輥道、燃燒控制、板坯物流跟蹤等控制對象的具體控制軟體流程、速度控制曲線、行程計算等具體控制策略和演算法，完成了攀鋼1450熱軋加熱爐基礎自動化系統（ l1 ）和熱工儀表的一級控制，實現板坯輸送、測量、裝出料、物流跟蹤、加熱爐燃燒控制以及板坯庫的數據信息交換，通過plc和二級計算機系統進行順序、定時、聯鎖與邏輯控制，實現了操作自動化與物料系統的全線跟蹤管理。
  3. To analysis combustor structure ’ s contribution to fluxion and combustion explicitly, it is necessary to study the impaction of wave system and fire temperature on chemical reaction and heat release ’ s procedure

    為了細致分析燃燒室結構和流動進口參數對超燃的作用關系，必須細化研究超音速流場的波系結構和燃氣溫度對化學反應放熱過程的影響。
  4. The experimental results indicates that the secondary mass flow increases with increasing of primary mass flow rate, but the bypass decrease because the primary mass flow rate increase more rapidly than secondary mass flow. the expansion configuration shows low thrust property due to low pressure in flow path. the secondary nozzle changes the pressure distribution in ejector combustor, and decreases bypass ratio, but obtain more completely mixing

    結果表明：二次流流量隨著一次流流量的增加而增加，由於二次流流量的增加速度低於一次流，引射系數減小；在純擴張式結構實驗中，引射燃燒室壓強很低，難以實驗推力增強；二次噴管改變了引射燃燒室的壓強分佈，降低了引射系數，改善了混合狀況能；對于本文的實驗結構，存在一個最優的二次噴管出口面積，使引射火箭推力最大，同數值模擬結果相吻合。
  5. Moreover, the data processing method of accelerated life test is used to solve the problem of the reliability data conversion under different operating status to liquid rocket engine. and the counter power law model is introduced as the relation model between the characteristic life and the combustion chamber pressure, the accelerated life equation of the constant stress accelerated life test for the weibull distribution is obtained, through the accelerated life equation, the reliability estimate of different combustion chamber pressure is calculated

    再次，採用加速壽命試驗的數據處理方法對液體火箭發動機不同工況下可靠性數據折算的問題進行了研究，引入逆冪律模型作為特徵壽命與燃燒室壓力之間的關系模型，得到了weibull分佈下恆定應力加速試驗的加速壽命方程，並通過加速壽命方程折算出不同室壓下的可靠度估計。
分享友人
分享到 Line

分享到臉書