燒結成型 的英文怎麼說

中文拼音 [shāojiēchéngxíng]
燒結成型 英文
sinter molding
  • 燒 : Ⅰ動詞1 （使東西著火） burn 2 （加熱或接觸某些化學藥品、放射性物質等使物體起變化） cook; bake; hea...
  • 結 : 結動詞（長出果實或種子） bear （fruit）; form （seed）
  • 成 : Ⅰ動詞1 （完成; 成功） accomplish; succeed 2 （成為; 變為） become; turn into 3 （成全） help comp...
  1. Taking the andalusite from south africa and alumina fiber as raw materials, adding aluminum sulphate as binder, fabrication and properties of alumina fiber reinforced andalusite composite was studied through wet dispersion, mould pressing and sintering processes

    以紅柱石和氧化鋁纖維為原料，用硫酸鋁作為結合劑，經過分散、混合、半干法成型、高溫燒成工藝，對氧化鋁纖維增強紅柱石基復合材料的制備及性能進行了研究。
  2. We also attainted mosi2 / sic composite by using melting mosi2 infiltrated sic body which shaped by sic powder. the result show that the diameters of sic particle and shaping methods have effect on the composite ' s microstructure and properties

    另外，嘗試了用mosi _ 2在2050下浸滲直接由sic粉體成型的坯體制備mosi _ 2 / sic復合材料。採用sic顆粒的級配有利於提高坯體密度，但是降低燒結體的緻密度。
  3. The material was sintered at 1050 for three hours to get the porous artificial bone, that its apparent porosity was54 %, its volume density was 1. 28 g / cm3, and its bending strength was 13. 25mpa. the results showed that the sintering temperature was reduced by adding bioglass

    本研究採用含生物玻璃前驅體粉末原料，添加檸檬酸造孔劑，模壓成型，在1050燒結保溫3小時，獲得了顯氣孔率為54 、體積密度為1 . 28s cm ~ 3 、抗彎強度為13 . 25mpa的多孔hap人工骨材料。
  4. The shaped briquet was sintered at 1600 for 2. 5 hours under normal pressure and at certain heating rate in si - mo electric furnace

    成型后的坯體置於硅鉬棒電爐中，在常壓、適當升溫速率下於1600保溫2 . 5小時燒結。
  5. To meet the processing requirements before sintering, the pressed briquet was pre - calcined at 1150 to make it possess adequate processing strength at first and then was shaped through precise turning on the numerical control lathe according to the design diagram of the femoral head prostheses of partial hip joint

    為滿足燒結前坯體加工的要求，壓制后的坯體在1150預燒，使其具備一定的加工強度，然後按照半髖關節股骨頭假體的形狀尺寸設計圖在數控車床上進行精密車削成型。
  6. Mas precursor powders were uniaxially pressed at 100 mpa employing a lubricated steel cylindrical mold. after sintering at 1450 for 2 hours, single - phase cordierite ceramic is prepared, and its relative density is 95. 1 %

    Mas先驅體粉末在100mpa的軸向壓力下成型后，經1450無壓燒結2小時，得到單相堇青石陶瓷，其緻密度達95 . 1 。
  7. To have outer cooling system though forced convection. exercisable processes : compressive sintering of cemented carbide and ceramic, moulding sintering in powder metallurgy

    實例：適合於硬質合金陶瓷件的加壓燒結，粉末冶金的成型燒結等。
  8. Based on the analysis of the characteristics of the raw mix slurry preparing process in alumina sintering production process, firstly, a mechanism model based on material balance principle was established as the master - rule model for the quality prediction ; secondly, considering the problem that the alkali liquor composition was unstable and its real - time measurement was difficult, a nn ( neural networks ) prediction model for the prediction of the alkali liquor composition was set up and nesting - integrated with the mechanism model ; finally, using the gray theory for the information mining from the errors of the mechanism model, a gm ( 1, 1 ) compensation model was put forward and parallel - connection - integrated with the mechanism model, achieving a raw mix slurry quality prediction model

    摘要針對燒結法氧化鋁生產過程中生料漿配料工藝的特點，根據物料平衡的原理建立機理模型，作為生料漿質量預測的主規律模型；針對堿液成分波動大且難以實時檢測的問題，對堿液成分含量建立了神經網路預測模型，並和機理模型進行嵌套集成；利用灰色理論對機理模型的偏差數據進行信息挖掘，建立了gm （ 1 ， 1 ）補償模型，並與機理模型進行並聯集成，獲得生料漿質量預測模型。
  9. The sls technology actuality in our country and abroad is analyzed

    本文分析了國內外選擇性激光燒結成型（ sls ）技術的研究現狀。
  10. The blended powder of nylon 12 and wollastonite was molded by selective laser sintering ( sls )

    摘要將尼龍12與硅灰石的混合粉末進行選擇性激光燒結成型。
  11. Mix organics into polytetrafluoethylene resin at low boiling point shaped by moulding and sintering

    利用低沸點有機物混入聚四氟乙烯樹脂經模壓乾燥燒結成型。
  12. The research of metal powder laser sintering is a hot topic in rapid prototyping technology area

    金屬粉末激光燒結成型技術是目前國內外快速成型領域的研究熱點。
  13. Secondly, the technics of selective laser sintering is also studied in this paper, we have received the best technological parameter through the experiment and analysis

    第二，對激光燒結成型工藝進行研究，經過正交實驗和方差分析后確定出最佳燒結工藝參數。
  14. The measure and method of minimize the sintering disfigurement is presented, which could be a guidance to the optimization of process parameter in the thermoplastic application of laser sintering prototyping

    並提出了減少燒結缺陷的措施和方法，這對激光燒結成型工藝在熱塑性塑料中的應用有一定指導意義。
  15. In this paper, nanosized al2o3 ceramic particles were chose as reinforcing phase. enhanced with ultrasonic wave the particles were covered with copper using method by electroless plating, the copper - matrix composite was developed by hot - press sintering process of the composite powder. the composition, microstructure, hardness, density and dry sliding wear property of the new material have been studied

    研究路線為：選用納米級al _ 2o _ 3陶瓷顆粒作為增強相，在超聲波的環境中用化學鍍的方法完成對納米al _ 2o _ 3陶瓷顆粒表面的金屬銅包覆，採用熱壓燒結成型技術以復合粉末為原料制備成納米al _ 2o _ 3陶瓷顆粒增強銅基復合材料，研究分析復合材料的成分、組織結構、硬度以及緻密度，對試樣進行了干滑動摩擦磨損實驗。
  16. The technics of the selective laser sintering for metal power covered with organic resin is studied in this paper, the content of research include three segments, firstly, we have finished the manufacture of 316l stainless steel metal power cocered with organic resin, the metal power covered with organic resin is applied by a lot of department and effect of use is very good, this technology also acquired patent

    並對覆膜金屬粉的選擇性激光燒結成型工藝進行了研究。研究主要從三個方面進行第一，完成了覆膜316l不銹鋼金屬粉的制備，應用該技術生產的覆膜金屬粉在許多單位得到應用取得良好效果且該項技術獲得了國家專利。
  17. The researching work include three aspects : 1 ) after selecting primary material system, the polymer coating process were optimized. the polymer - coated high - temperature alloy powder has been developed on the basis. 2 ) based on sintering and orthogonal experiments, the influence of the prototyping elements on prototyping properties have been initially studied, and the optimal prototyping parameters of this material has been obtained finally

    本文主要研究內容為： （ 1 ）選擇合適的包覆材料體系，對鉬粉的包覆工藝進行了優化實驗，在此基礎上開發了適合於激光燒結成型用覆膜高溫合金粉末材料； （ 2 ）通過激光燒結成型實驗，運用正交實驗方法，系統地研究了燒結工藝參數對成型質量的影響關系，在此基礎上確定了覆膜高溫合金粉末最佳燒結成型工藝參數； （ 3 ）對激光成型件進行了后處理工藝實驗，得到了優化的后處理工藝規程，並製作了合格的后處理樣件。
  18. Under the background of correlative research project, the method of selective laser sintering has been used in the researching work. polymer - coated high - temperature alloy powder have been first developed successfully in our nation. the laser sintering and post - treatment process of high - temperature alloy parts have been systematically studied, which lay the foundation for its engineering application

    在國內首先研製成功了覆膜高溫合金粉末及其制備工藝，並對其激光燒結成型和后處理工藝進行了系統的實驗研究，為該項技術的工程化應用打下了基礎。
  19. Material is cement, sand, coal dust, high pressure molding, need not sinter. the product with good strength, colourful

    原料由水泥、黃砂、粉煤灰組成，高壓成型無需燒結，成品瓦強度高、色彩豐富。
  20. In this paper, a series of experiments are carried out with dlms for nickel - based metal powder materials, and the effect of process parameters in sample quality was investigated and analyzed. the main works are as following : ( 1 ) the effect mechanism of laser in metal powder and the nucleation mechanism are analyzed. ( 2 ) the process parameters that affect the quality of sintering parts are investigated and the way how they affect is clear

    本文基於直接激光金屬燒結成形技術，通過對鎳基高溫合金直接激光燒結成形的研究，從工藝角度研究某型號鎳基高溫合金的激光直接燒結成形性能以及工藝參數對燒結製件性能的影響，所完成的工作主要有: （ 1 ）分析材料與激光相互作用的機理及熔池的動態快速凝固過程。
分享友人
分享到 Line

分享到臉書