燒結機 的英文怎麼說

中文拼音 [shāojiējī]
燒結機 英文
agglomerating machine
  • 燒 : Ⅰ動詞1 （使東西著火） burn 2 （加熱或接觸某些化學藥品、放射性物質等使物體起變化） cook; bake; hea...
  • 結 : 結動詞（長出果實或種子） bear （fruit）; form （seed）
  • 機 : machineengine
  1. Application of sonic wave dust cleaner in head end ep of sintering machine

    聲波清灰器在燒結機頭電除塵器中的應用
  2. Updraft sintering machine

    鼓風燒結機
  3. The reasons of high energy consumption on sintering machine no. 2 at xiangtan i & s co were discussed from the results of heat balance test

    摘要根據湘潭鋼鐵公司（以下簡稱湘鋼） 2號燒結機能耗現狀和熱平衡測試結果分析了該燒結機能耗高的原因。
  4. Tsdc measurements of coal fly ashes

    燒結機尾電除塵器的脈沖供電
  5. Combining the characteristic of the fabrication of fgm by particle co - sedimentation, the densification of fgm has been designed from three aspects : the densification mechanism, the correlative parameters of the additives and the sintering schedule. subsequently, the densification of the w - mo - ti system composites has been investigated

    結合共沉降法制備功能梯度材料的特點，從緻密化的機理選擇，燒結劑種類、含量和粒度的確定，燒結機制的確定等三個方面對其緻密化思路進行了設計，並對論文選用的w - mo - ti體系的復合材料的緻密化進行了初步研究。
  6. Abstract : in this paper, two tests are described on air leakage of sinter machine in 2 sintering plant of xiangtan iron and steel co. according to the test results, on the base of analysis and discussion, a series of measures on decreasing air leakage of sinter machine are putted forwored from sealed devices, lubricating oil system, maintenance and management etc. an effective and feasible way is supplied for energy saving and increasing production, decreasding production cost, increasing economy benefit of sintering process

    文摘:通過對湘鋼二燒燒結機漏風率的兩次測試和結果分析，從密封裝置、潤滑系統、附件結構的改進等方面提出了一系列降低漏風率的對策，為燒結工序的增產節能，降低生產成本，提高經濟效益提供了一條行之有效的途徑。
  7. Optimization of iron ore material composition for 24 m2 sinter machine

    2燒結機原料結構優化
  8. Thorough treatment of smoke and dust at head part of sintering machine

    燒結機機頭煙塵深度治理實踐
  9. Improvement in the structure of multi - tube dust extractor in sintering machine

    燒結機機頭多管除塵器結構改進
  10. Characteristics amp; amp; applications of electrostatic precipitator for sintering dust

    布袋除塵器在燒結機機尾除塵中的應用
  11. D. l. sintering machine dl

    型帶式燒結機
  12. Analysis on breakage and system fault on universal shaft on cold - hot screen of sinter machine

    燒結機冷熱篩萬向傳動軸斷裂及系統故障分析
  13. It bought another secondhand blast furnace and a sinter machine from arbed in luxembourg

    它還從盧森堡的一家公司購買了一座二手高爐和一個燒結機。
  14. The new sprocket, manufactured by means of this equation, can improve the logistic movement of the pallet cars, reduce the impact and establish the foundation of producing archless sintering machine

    利用該方程製造的新型星輪能夠改善臺車的邏輯運動，減小沖擊，為製造無起拱燒結機奠定了基礎。
  15. Application of esp for flue dust control at the head of sintering machine

    靜電除塵在燒結機頭煙塵治理中的應用
  16. The micromorpholgy and grain boundary microstructure of the material were studied with sem and tem and the grain boundary phase composition were analyzed with eds and x - ray the mechanical properties, micromorpholgy microstructure of grain boundary and phase composition of al2o3 composite ceramics were systematically studied, the effect of additives, the relationship between microstructure and mechanical strength, the sintering mechanism of the material and influence factors of the structure and properties of al2o3 composite ceramics were discussed respectively

    系統研究了氧化鋁陶瓷的力學性能、微觀形貌、晶界顯微結構，並討論了各添加組分的作用、材料顯微結構與力學性能的關系以及材料的燒結機理和影響材料結構與性能的影響因素。本論文探討了氧化鋁基復相陶瓷的強韌化機理，實驗表明al _ 2o _ 3 - ticn體系主要是微裂紋韌化。
  17. Based on the mechanics calculation and motion simulation of the pallet draught device, the force control threshold value and the force control curve of a new type 60m ^ 2 sintering machine were obtained

    在對臺車執行牽引裝置進行力學計算和運動模擬的基礎上，得到了新型60平分公尺帶式燒結機的力控制閾值和力控制曲線。
  18. But there is a few findings in the study of low temperature sintering, which cries for more efforts putting into the mechanical study of low temperature, to find a method for technology promoting and enrich the known activation sintering theory

    然而國內外在低溫燒結機理方面的成果乏善可陳，這就迫切需要加大對低溫燒結機理研究的力度，為工藝提升找到一條路，並且豐富已知的活化燒結理論。
  19. Taking the kinematics and dynamics problems of pallet cars on an even - tooth sintering machine into comprehensive consideration, a new kind of tooth shape, which could bring variational acceleration to a single pallet car, had been put forward

    摘要綜合考慮偶數齒燒結機臺車的運動學和動力學問題，提出了能使單輛臺車產生變加速運動的新型齒型。
  20. By analyzing the mechanics relation between the sprocket wheel and the pallets of the pallet draught device in a sintering machine, the non - arching mechanics model of the pallets was established and the force control method for the non - arching sintering machine was put forward

    摘要通過分析帶式燒結機臺車執行牽引裝置的星輪和臺車的力學關系，建立了臺車無疊肩起拱的力學模型，提出了無疊肩起拱帶式燒結機的力控制方法。
分享友人
分享到 Line

分享到臉書