燒結料 的英文怎麼說

中文拼音 [shāojiēliào]
燒結料 英文
agglomerated charge
  • 燒 : Ⅰ動詞1 （使東西著火） burn 2 （加熱或接觸某些化學藥品、放射性物質等使物體起變化） cook; bake; hea...
  • 結 : 結動詞（長出果實或種子） bear （fruit）; form （seed）
  • 料 : 名詞1 （材料; 原料） material; stuff 2 （喂牲口用的穀物） feed; fodder 3 （料器） glassware 4 （...
  1. ( 2 ) the properties of the material with finer andalusite particle size are superior to those of coarse particle size at lower temperature, but properties of material of fine and coarse particle size have little difference at higher temperature. this illustrates that the andalusite particle size can lower the sintering temperature and that it brings forth not remarkable influence on the property of the material when the material is sintered completely

    （ 2 ）對于不同粒度的原料，在燒成溫度較低的情況下，粒度小的材料性能明顯高於粒度大的材料，但在燒成溫度較高的情況下，兩者差別不大，說明原料粒度減小能降低製品的燒結溫度，但在制品均完全燒結的情況下對材料性能影響不大。
  2. We also attainted mosi2 / sic composite by using melting mosi2 infiltrated sic body which shaped by sic powder. the result show that the diameters of sic particle and shaping methods have effect on the composite ' s microstructure and properties

    另外，嘗試了用mosi _ 2在2050下浸滲直接由sic粉體成型的坯體制備mosi _ 2 / sic復合材料。採用sic顆粒的級配有利於提高坯體密度，但是降低燒結體的緻密度。
  3. Sintered bimetal material - determination of shear strength

    燒結雙金屬材料剪切強度的測定方法
  4. The material was sintered at 1050 for three hours to get the porous artificial bone, that its apparent porosity was54 %, its volume density was 1. 28 g / cm3, and its bending strength was 13. 25mpa. the results showed that the sintering temperature was reduced by adding bioglass

    本研究採用含生物玻璃前驅體粉末原料，添加檸檬酸造孔劑，模壓成型，在1050燒結保溫3小時，獲得了顯氣孔率為54 、體積密度為1 . 28s cm ~ 3 、抗彎強度為13 . 25mpa的多孔hap人工骨材料。
  5. Using in situ formation of ternary boride base cermets hard phases through chemical reactions and sinterbonding onto steel substrates though liquid sintering we successfully prepared a kind of ternary boride base cermet

    摘要通過化學反應將原料粉來生成三元硼化物硬質相併通過液相燒結燒與鋼很好的結合，用這種工藝成功地在鋼基體上塗覆了預壓制的三元硼化物基金屬陶瓷。
  6. Materials for sintered neodymium iron boron permanent magnets

    燒結釹鐵硼永磁材料
  7. In recent years at iron - making plant of pangang, the coke ratio of pig iron has reduced evidently by insisting on “ burden preparation ” course, improving quality of sinter, raising wind temperature, increasing rich oxygen quantity and injecting abundant pulverized coal into bf. the solid fuel consumption of sinter has been decreased greatly through insisting on using high - quality calces, practising high feed sintering, actualizing many techniques in solving key problems. at the same time, the energy source base management has been strengthened, and energy - saving work has made great progress, profits generated by energy - saving have exceeded a hundred million yuan

    近年煉鐵廠通過堅持「精料」方針，改善燒結礦質量，提高風溫，增大富氧，實施大噴煤，使入爐焦比有明顯下降；燒結堅持用好生石灰，推行厚料層燒結，實施多項技術攻關，固體燃耗大幅度下降；同時加強能源基礎管理，節能工作取得長足進步，節能創效益1億元以上。
  8. Ceramic elements are made by pressing and sintering finely powdered materials.

    陶瓷元件是將仔細研磨的材料經過加壓和燒結製成。
  9. Widely employed in coal mine, downhole coal bunker, coal washery, cement factory, foundary, thermal power plant, sintering plant coal gas factory, fertilizer plant, chemicals plant, aluminium plant, alkali factory, steel works, coking plant, pharmaceutical factory, mine, dock, foodstuff, and feedings process works, concrete process, etc. with bunker, hopper, transmitting pipeline and drawshaft

    廣泛用於煤礦、及井下煤倉、洗煤廠、水泥廠、鑄造廠、火力發電廠、燒結廠、煤氣廠、化肥廠、化工廠、鋁廠、制堿廠、鋼鐵廠、焦化廠、制藥廠、礦山、碼頭、糧食、飼料加工廠、混凝土加工廠等擁有料倉、料斗、輸送管道和礦山溜井的廠礦企業。
  10. Lifepo4 was sintered by solid - state method, we found that the capacity of the sample which was synthesized by codeposition method exhibited high specific capacity ( 142 mah ? g - 1 ) and good cycling performance

    採用高溫固相法制備了lifepo4 ，發現共沉澱制備的前驅體燒結出的材料容量達到142mah ? g - 1 ，循環性能也很好。
  11. As a comparison, ba1. 03ce0. 8gd0. 2o3 - was synthesized by sol - gel method. among these samples, nonstoichiometric samples were synthesized for the first time. the research work involved : the crystal phase of the sinters were determined by xrd ; ionic conduction under different experimental atmospheres was measured by gas concentration cells ; performances of hydrogen - air fuel cells with the sinters as electrolytes and porous pt as electrodes were measured

    用粉末x射線衍射儀鑒定它們的結晶相；在（ 600 1000 ）范圍內，以燒結體作為電解質隔膜，多孔性pt黑為正、負電極， pt - rh合金網為集電極，分別組成氫濃差電池、氧濃差電池及氫?空氣燃料電池並測定了它們的性能，研究了不同氣氛下樣品的離子導電特性及影響燃料電池性能的因素。
  12. In chapter two, we fabricated r - ni - fe / al2o3 nanocomposites successfully by using ball - milling mixing method plus hot - pressing process. meanwhile, their microstructures are characterized by x - ray diffraction ( xrd ) analyser, transmission electron microscopy ( tem ), field emission scanning electron microscopy ( fe - sem ) and brunauer - emmett - teller ( bet ). the results indicate that ni - fe particles are homogenously dispersed in the matrix in the composites

    在第二章中，我們採用高能球磨混合方法加上熱壓燒結工藝，成功制備了ni - 20fe al _ 2o _ 3納米復合材料，並通過x射線衍射儀（ xrd ） 、透射電鏡（ tem ） 、場發射掃描電鏡（ fe - sem ） 、比表面孔隙儀（ bet ）對該復合材料的微結構進行了表徵。
  13. Characteristic and suitablescope the surface basic is 10 steeil and spcc, then sinter 20high - tin, the manufacture has good antifriction, no fever heat, against grip axes, suitable for engines camshaft and pneumatic engine, refrigerating machine bushes. at present, our factory is the greatest export factory for eccentric bushes in the domestic area, and match bushes to isuzus idler gear for japanese isuzu co

    表面以10鋼或spcc低碳鋼為基礎，表面燒結錫合金材料扎制而成，產品具有耐磨性能好，不發熱，不咬軸等優點，特別適用於發動機凸輪軸，氣壓機，製冷機軸套，目前我廠是國內出口偏心軸瓦的最大廠家，並一直為日本五鈴公司配套五十鈴惰輪襯套，和國內各主要柴油機廠配套。
  14. The formation of new phase such as mullite and gahnite by solid - phase reaction in multiphase materials can benefit the sintering of materials at 1700, decreased apparent porosity to less than 5 %. reducing atmosphere inhibited the synthesis of mullite and gahnite, played a negative role in the densification of multiphase materials

    固相反應生成的鋅鋁尖晶石和莫來石具有較高的活性，使復相材料在1700燒后顯示出更好的燒結性能，其顯氣孔率降低到5以下；還原性氣氛阻礙了莫來石和鋅鋁尖晶石的生成，不利於復相材料的燒結和緻密化。
  15. Study on the synthesis of corundum - mullite - gahnite multiphase materials by two - step sintering process using kaolinite as raw material showed that impurities introduced by kaolinite mainly increased the liquid amount at high temperature, which can assist sintering of specimen. the experiment results indicated that the samples with lower gahnite content had better sinterability than others. however, if the gahnite content was relative high, the promoting effect on sinterability caused by kaolinite was not significant

    採用天然原料高嶺土二步煅燒合成剛玉?莫來石?鋅鋁尖晶石復相材料研究發現：天然原料中帶入的雜質主要是增加液相量，促進高溫下試樣的燒結；當尖晶石含量較低時，試樣在1300保溫2h時，在1600燒后試樣燒結性能相比之下較好；而當鋅鋁尖晶石含量較高時，天然料對試樣的促燒作用不是非常明顯。
  16. Study on the synthesis of corundum - mullite - gahnite multiphase materials by one - step sintering process using high purity raw materials showed that the more the content of gahnite in multiphase materials, the high the volume expansion would be introduced in the system, which resulted in the sintering difficulty of the multiphase materials. while the content of gahnite was controlled about 30wt % and the content of mullite was about 70wt %, the densified multiphase materials can be obtained after fired at 1600 or 1700

    採用高純原料一步合成剛玉?莫來石?鋅鋁尖晶石復相材料研究表明：復相材料中鋅鋁尖晶石含量越高，則合成鋅鋁尖晶石時產生的體積膨脹越大，燒結性也就越差；當鋅鋁尖晶石含量為30wt ，莫來石含量較高為70wt左右時，在1600或1700燒后都能得到顯微結構較為緻密的復相材料。
  17. Sicp / al matrix composites, with 5, 15 and 25 % volume fraction of sic particles, were prepared by vacuum hot - pressing sintering processing in this paper. based on mechanics properties, sem observation and energy dispersive x - ray analysis, the interface reaction phenomenon of sicp / al composites made by vacuum hot - pressing sintering, as well as the reinforcement and fracture mechanisms of this composite were analyzed. the dynamic responses of sipc / al composites were studied by a split hopkinson high - speed pressure bar impact system which strain rate was from quasistatic state strain rate ( 3. 3 10 - 3s - 1 ) to dynamic state strain rate ( 5. 2 103 s - 1 )

    本研究以武裝直升飛機防護裝甲材料為研究對象，採用真空熱壓粉末冶金燒結工藝制備了含sic顆粒體積分數分別為5 、 15和25的sic顆粒增強鋁基復合材料，結合其力學性能、掃描電鏡和界面微區能譜分析結果，分析了sic _ p al復合材料的真空燒結過程中的界面現象，以及材料增強和斷裂機理，並利用hopkinson高速壓桿沖擊實驗系統對其從靜態到動態（應變率為3 . 3 10 ~ （ - 3 ） s ~ （ - 1 ） 5 . 2 10 ~ 3s ~ （ - 1 ） ）的壓縮破壞響應進行了研究，分析了不同體積分數sic _ p al復合材料高應變率壓縮載荷下，材料的變形和微觀損傷機理，以及利用高速沖擊空氣炮測定了改復合材料制備剃度復合板的穿透性能。
  18. Application of sintered soft magnetic iron to miniature motors

    燒結軟磁材料的性能及在電動機上的應用
  19. Technical features : utilizes advanced second sintering technology, and has world - advanced fully computerized multi - pipe spreading technology, compounding microlite glass to surface of vitrified tile, and organically blend through second high temperature firing, so the product achieves a higher level in strength, luster and surface crystal feeling

    技術特點：採用領先的二次燒結技術和具有國際先進水平的全電腦多管道布料技術，將微晶玻璃復合在陶瓷玻化磚的表面，經二次高溫煅燒有機融合於一體，令產品強度、光澤度與表面晶瑩質感達到另一個高度。
  20. Modeling of water feeding process for sinter - mixture by modified neural network

    燒結料加水混合過程的改進神經網路建模
分享友人
分享到 Line

分享到臉書