燒蝕的 的英文怎麼說
中文拼音 [shāoshíde]
燒蝕的
英文
ablating-
Laser marking is a kind of technique using heat effect of laser to ablate meterials on object surface so as to leave over permanent press
激光打標是利用激光的熱效應燒蝕掉物體表面材料從而留下永久標記的技術。The charter i introduced the schematics of the experimental setup, the model of pulsed laser ablating solid target ( s - n model ) and the subplantation model for film growing proposed by y. lifshitz
第一章簡要介紹了實驗裝置、激光燒蝕固體靶的s - n模型和y . lifshitz提出的次表面生長模式。Ablation performance and mechanism of 3d c c composites
復合材料的電弧駐點燒蝕及機理分析Improvement on ablation and erode of mechanized gun evacuator
自行火炮抽氣裝置防燒蝕腐蝕的改進試驗Ablative - cooled refractory
燒蝕冷卻的耐火材料At last, the effect on the outer ballistic trajectory characteristic after the ablation of hypersonic projectile wing has been analyzed
最後，初步分析了高超聲速彈翼表面發生燒蝕后對其外彈道特性的影響。Mathematical model for predicting melt - erosion in gun barrels
身管熔化燒蝕的預測數學模型On the origin of substrate erosion in chromium plated gun barrel
鍍鉻槍管的基體初始燒蝕行為The basic physical mechanisms of the electrode erosion process of high power gas switches were also studied
研究了高功率氣體火花開關電極燒蝕的基本物理過程。Abstract : from the point of theoretical analysis, this dissertation provides the coupling calculation on the hot gas temperature field and ablation in the cavity between stress release boot and insulation of solid motors. through the calculation, some law of the ablation of the stress release boot is found
文摘:從理論分析的角度出發，通過對人工脫粘層和絕熱層所構成的槽縫燃氣溫度場與燒蝕的耦合計算，得出了人工脫粘層的燒蝕規律。The interior temperature distribution and ablation model of projectile wing is established from general transmitting heat differential equation ; at the same time, the heat flow density and pressure distribution model of projectile wing is also established
從一般形式的導熱微分方程出發，逐步建立了彈翼內部溫度分佈和燒蝕的數學計算模型；與此同時，建立了彈翼表面的熱流密度和壓力分佈的數學模型。Study of reducing erosion of rail electrode surfaces in railgun
減輕軌道炮炮膛燒蝕的研究The conclusion obtained from experimental result showed that particle concentration is an important factor on inhibitor ablation
試驗結果表明：粒子聚集濃度是絕熱層燒蝕的重要影響因素。Test method for heat of ablation
燒蝕的熱試驗方法Influence of rotary arc on the feature and electrode erosion of spark switch
旋轉電弧對火花間隙開關電極燒蝕的影響Focused on the relationship between ablation and its influence ingredients, this paper analyzed simulation techniques of flow field under high acceleration condition
針對高過載問題中絕熱材料燒蝕的影響因素，進行了地面模擬高過載發動機流場的方案分析。Ablation experiments were carried out using this system to study main factors that influenced ablation. the experiment results showed that such parameters as oxygen percentage and pressure would affect ablation greatly
通過改變富氧含量、燃燒室壓強等參數進行了不同工況下的燒蝕實驗，分析了影響燒蝕的主要因素。In order to explore the influence of particle diameter on flow field and ablation, particle collection experiments under simulated acceleration conditions were conducted and diameter distribution was obtained
為分析粒徑對流動計算、燒蝕的影響，開展了模擬過載條件下的粒子收集試驗，獲得了在聚集狀態下的粒徑分佈。By observing the macrocosmic and microcosmic state of the test specimens, the ablation pattern of inhibitor was put forward and ablation mechanism was analyzed. the critical average particle diameter that influenced inhibitor ablation was obtained. the time - dependent ablation expression associated particle concentration and angle was achieved through analyzing their variation alone with the change of specimen figure
（ 4 ）通過對試驗后絕熱材料試件的表觀和微觀狀態分析，提出了過載條件下絕熱層的燒蝕模式，並分析了其燒蝕機理，獲得了試驗條件下影響絕熱層燒蝕的平均顆粒直徑。To find the ways to increase repetition rates and lifetime of the switches, mechanisms of two physical processes which determine repetition rates and lifetime of the switches, dielectric recovery and electrode erosion, were studied in theory, and a serial of high - energy high - coulomb repetitive experiments were performed with two different three - electrode gas spark switches designed by ourselves
為了探尋提高開關重復頻率和壽命的技術途徑和方法，對制約開關重復頻率和壽命的兩個主要物理過程?絕緣恢復和電極燒蝕的機理進行了理論研究。設計了兩種形式的三電極吹氣式氣體火花開關，並進行了高能、大電荷量重復頻率實驗研究。分享友人