盤式閥 的英文怎麼說
中文拼音 [pánshìfá]
盤式閥
英文
disc valve-
The litter - resistance slowly closing butterfly check valve is developed a newest product based on our butterfly check valve, hydra - matic transmission to be add in the valve with unique design, new stuction and optimum performance, can be used pipeline of water supply and dring with such media : fresh water, sea water, sewage, raw water, ect. the valve should be installed at outlet of the water pump, in stapping the pump, the process of slowly closing after valve plate shuts rapidly. can be guard effectively against the destruction water hummer, so to ensure the safe operation of the pipline
微阻緩閉蝶式止回閥是在我廠生產的蝶式雙瓣止回閥的基礎上利用能量轉換原理增設油壓緩閉裝置的新型模式止回閥，設計獨特，結構新穎，性能優宜，適用於凈水，源水，污水，海水等介質的供、排水管路中，安裝於水泵出口端，停泵時由於油壓阻尼作用法盤先速閉后緩閉，以消除破壞性水錘，保證灌路安全運行。Comparing and analyzing the synchronous control strategy, which brings up the new method to control the double un - symmetry jars proceed synchronously with the combination of proportional valve and servo valve, which forms closed loop control ; basing on the above methods, models are made to get mathematics models of position control system and to analyze system model theoretically by using pid controller, we can realize regulating parameters, minimizing synchronous errors and enhancing the dynamic performances ; the simulink tool box in matlab software is used to imitate the system according to the model, which not only makes the result visual and easy to adjust the parameters in interactive way but also lets us understand the effects of different parameters and optimizes the dynamic properties. the theory of plc control in dshp is discussed after advanced understanding of the system movements. hardware design and general regulation are given on the base of siemens company products s7 - 200 plc
本文根據大量的國內外文獻，對研配液壓機的工作原理及設計結構進行了簡介；對位置同步的控制方法進行了比較分析，提出比例閥和伺服閥復合控制的閉環結構來對非對稱雙缸進行同步控制電液比例同步控制方案；在此基礎上著重對比例閥控非對稱缸建模，最後得到位置控制系統的總體數學模型，從理論上對同步系統動態特性進行了分析，並用pid控制器進行參數整定，減小雙缸同步誤差、提高系統的動態響應性能；其中控制性能的分析藉助于matlab軟體中的simulink工具箱，由已建立的數學模型形成模擬模型，得到可視化的模擬結果，從而利於交互方式下調整參數，了解不同的參數對系統的影響，優化同步系統的動態性能；在深入了解系統的動作特性后，對plc控制研配液壓機的原理進行了探討，針對siemens公司s7 ? 200型plc給出了硬體設計的總體規劃，編制出研配液壓機動作控製程序，在編程中著重研究位移傳感器與plc的通訊、雙缸同步運行的pid控制在plc上的實現及bcd碼撥盤輸入程序的植入問題。Cross flow cap tray
錯流式浮閥塔盤The valve plate is made of air gasket type valve plate
閥盤結構為空氣墊型膜式閥盤。The equipment made by us of titanium, stainless steel, aluminum or plastics, mainly include column condenser ( heat exchanger ) ; coil hear exchanger ; membrane evaporator ; constant boil tower ; reactor ; pressure filter, storage tank ; blower, centrifuge and ta series corrosion - resist titanium pump, as well as variety of metal constructional member. they are widely applied in the industries of petrochmical engineering, smelt, pharmacy, chlorinate alkali, salt preparation, as well as electric chemical plant
我廠生產鈦材，不銹鋼等各種材質的化工設備，主要有風機，離心機，鈦泵，鈦閥，列管式冷凝器（換熱器） ；盤管式換熱器；薄膜蒸發器；塔器；反應器；貯存容器；面向石油化工，冶煉，制藥，氯堿，制鹽食品，造紙，環保等化學工業領域及電化行業。Hydraulic fluid power - two -, three - and four - port screw - in cartridge valves - cavities
液壓流體動力.二孔三孔和四孔擰入式卡盤閥.孔腔One of the key problems of designing the control valve of modulation rotary steering drilling tool is the design of high pressure hole of upside valve
摘要設計調制式旋轉導向鉆井工具控制閥的關鍵問題之一是上盤閥高壓孔的設計。According to the work principle, mechanical model theory and simulation analysis of the hydraulic control valve of the drilling tool, the optimal design parameters of the angle of center of circle of the high pressure hole of upside valve are proposed ; the influence of the charging and discharging lag times on palm supporting capacity is discussed ; and the theoretic basis of designing the control valve of the drilling tool is put forward in the paper
通過對調制式旋轉導向鉆井工具液壓盤閥機構的工作原理、力學模型的理論和模擬分析，給出了上盤閥高壓孔圓心角的最優設計參數；討論了充液、泄液滯后時間對巴掌支撐力的影響，提出了調制式旋轉導向鉆井工具控制閥機械設計和控制的理論依據。Cavities for hydraulic fluid power cartridge valves - specification for two - port slip - in valves
液壓動力卡盤式閥的空腔.第1部分:二通鑲套滑動閥規范According to bernoulli theorem, kinetic energy and potential energy change due to the thermokinetic differences of steam and conden sation water, and action valve plate starts and stops to choke air and drain water
圓盤式疏水閥是根據伯努力熱動力原理，利用蒸汽和凝結水通過閥孔時流速和何種產生變化的不同熱力學性質，驅動閥片開關閥門，從而達到阻汽排水。It is suitable for close tolerance applications such as transmission valve bodies, and disk brake pistons where good dimensional stability and compatibility with transmission and brake fluid is essential
本產品適宜於模塑成型，工藝性能良好。適用於製造對製品的尺寸穩定性有較高要求的結構件，如轉動閥門的殼體盤式剎車活塞等。分享友人