直角計算尺 的英文怎麼說

中文拼音 [zhíjiǎojìsuànchǐ]
直角計算尺 英文
square slide rule
  • 直 : Ⅰ形容詞1 （成直線的; 硬挺的） straight; stiff 2 （跟地面垂直的; 從上到下的; 從前到后的） erect; v...
  • 角 : 角Ⅰ名詞1 （牛、羊、 鹿等頭上長出的堅硬的東西） horn 2 （古時軍中吹的樂器） bugle; horn 3 （形狀像...
  • 計 : Ⅰ動詞1 （計算） count; compute; calculate; number 2 （設想; 打算） plan; plot Ⅱ名詞1 （測量或計算...
  • 算 : Ⅰ動詞1 （計算數目） calculate; reckon; compute; figure 2 （計算進去） include; count 3 （謀劃;計...
  • 尺 : 尺名詞[音樂] （中國民族音樂音階上的一級 樂譜上用做記音符號 參看「工尺」） a note of the scale in ...
  • 計算 : 1 （求得未知數） count; compute; calculate; reckon; enumerate 2 （考慮; 籌劃） consideration; pla...
  1. Do some necessary calculations and decide on the general scheme of compton back - scattering imaging scanner to the real wall inspection. include the selection of radioactive source, the calculation of compton back - scattering beam, the calculation of the basic condition of finding out the different materials and the determination of some important parameters as well. 3

    其主要內容包括入射源的選擇，散射粒子的理論計算，發現異物的最低條件計算以及系統的一些重要參數的確定，主要包括：放射源的選擇，散射角的確定，后準直器的形狀與尺寸，前準直器的尺寸，前準直孔的大小，檢測器的種類與型號，檢測器的效率等。
  2. Analyze item by item the position of unintact cycle, the running clearance of unintact cycle, locking - deform, datum dimension regulating, repeatly install, power voltage wave and marking running etc. at the same time, we give the calculating formula to calculating the running marking random error, and use it to calculate the system error of big diameter measure instrument - - datum dimension frame error, gyro - wheel diameter error, error caused by circumstance temperature, error caused by backing distance, angle error, delay error of data collecting circuit, lathe main shaft running error, workpiece install partial error

    對不完整圓的位置、不完整圓的轉動間隙、鎖緊變形、基準尺調整、重復安裝、電源電壓波動、標記轉動等隨機誤差進行了逐項分析，並給出轉動標記隨機誤差的計算公式。對大直徑測量儀的系統誤差?基準尺尺架誤差、滾輪直徑誤差、環境溫度引起的誤差、後退距離引起的誤差、角度誤差、數據採集電路延時誤差、車床主軸回轉誤差、工件安裝偏心誤差分別進行了計算，最後對誤差進行合成。
  3. According to elasto - plasticity theory, with the help of finite - method program ansys, the paper undertakes the computer analogue tests about the bearing capacity of pile tip arranged by orthogonal principle, and attains the relations of pile - tip bearing capacity to embedment depth, pile diameter, cohesion, internal friction angle and modulus of deformation. by the means of mathematical statistic, regression equation of the ultimate bearing capacity calculated by finite element method is gained through the regression analysis of 81 group data from the computer analogue tests. by comparison and analysis of the values calculated by finite - element regression equation and the values of in situ loading test, the regression equation is gained which calculates the size effect for base resistance of large diameter pile

    根據彈塑性理論，運用大型有限元軟體ansys按正交設計理論對樁端承載力進行模擬計算，獲得樁端承載力與樁長（埋置深度） 、樁徑、粘聚力、內摩擦角及變形模量等主要影響因素的關系，並採用數理統計方法，對81組ansys模擬試驗結果數據進行回歸分析，得到有限元法確定樁端極限承載力的回歸公式，並將有限元法回歸公式計算值與現場小壓板載荷試驗值進行比較分析，得到大直徑樁端阻的尺寸效應系數計算公式。
  4. Thus, the conclusion is drawn : when the diffusion coefficient of cf is invariable and the diffusion time is under a certain range, the beginning corrosion time of the steel in the corner of the rectangular section is independent of the size of rectangular section ; ( 4 ) through the numerical value calculation of rectangular section, the law is found of the influence on modifying coefficient of rectangular section of the thickness of protection layer of concrete and diameter of the steel and the thickness of cf on the surface of concrete, based on which practical calculating method of beginning corrosion time of the steel in the corner of rectangular section is set up

    從而得到結論：在氯離子擴散系數一定的情況下，在一定時間范圍內，矩形截面邊角區域鋼筋的初始銹蝕時間不依賴于矩形截面的截面尺寸； （ 4 ）通過矩形截面邊角區域鋼筋初始銹蝕時間的計算，分析了保護層厚度、鋼筋直徑、混凝土表面氯離子濃度對修正系數的影響，並在此基礎上建立了氯離子侵蝕下矩形截面邊角區域鋼筋初始銹蝕時間的實用計算方法。
分享友人
分享到 Line

分享到臉書