相似多邊形 的英文怎麼說
中文拼音 [xiāngsìduōbiānxíng]
相似多邊形
英文
shape similarity-
Leaves tufted ; stipes 15 - 30 cm long, densely scaly at base, glabrous above ; sterile lamina about 60 cm long and 20 cm wide, simply pinnate ; pinnae numerous, alternate or subopposite, linear - lanceolate, the largest about 12 cm long and 1 cm wide, base cordate, apex acuminate, margin finely toothed ; veins close, forking once or twice and forming areoles near the midrib ; fertile lamina similar to sterile ones, but somewhat reduced, about 8 cm long and 0. 4 cm wide, lower surface almost entirely covered with sporangia
葉簇生；葉柄長15 - 30厘米，基部密被鱗片，向上近光滑；不育葉片長約60厘米，寬20厘米，一回羽狀；羽片多數，互生或近對生，線狀披針形，最長者長達12厘米，寬約1厘米，頂端長漸尖，基部心形，邊緣有細密鋸齒；葉脈1 - 2次分叉，近中脈形成網眼；能育葉與不育葉相似，但較小，長約8厘米，寬約0 . 4厘米，下部滿布孢子囊。Presents the microstructure evolution in aluminum a nd copper after deformation by cold rolling in the strain range of 10 to 50 % red uction using tem and points out three types of dislocation structures are typica l and two of them are common for both materials and these two common types are f ound in non - cube grains and can be distinguished by crystallographic orientatio n of dislocation boundaries in the grains and the third type of structure is obs erved in cube grains, and concludes that grain orientation is important in deter mining the structure type but some other metallurgical parameters also have a ro le to play
採用tem對冷軋多晶銅與多晶鋁的形變顯微組織演變進行了對比研究.結果發現：多晶銅及多晶鋁形變顯微組織中均含有三類典型的位錯結構類型，其中的兩種結構特徵在兩種材料中是相似的，這兩種類型結構存在於非立方取向晶粒，可通過晶粒中位錯邊界的晶體學取向加以區別，另一類型結構存在於立方取向晶粒；晶粒的晶體學取向決定了其形變顯微組織類型，但其它冶金學因素對顯微組織也有影響Review of watermarking techniques for 3d polygonal models
基於力學的多邊形相似性測度方法To fulfill the need of the application of rp technique in medical domain, reverse cad modeling from medical cross sections is systematically studied in this dissertation. firstly, some algorithms related to the research of this dissertation are studied. new algorithms for orientation and inclusion test for simple polygon, an error constrained automatic faring algorithm for b - spline curve and a theorem regarding the termination criterion for subdivision of triangular bezier patch are proposed
本文針對rp技術在醫學領域應用的需要，系統研究了基於醫學斷層輪廓數據的反求cad建模理論和方法： （ 1 ）在基礎演算法研究部分，提出了簡單多邊形方向及點在多邊形內外判斷的新方法、三角b zier曲面片離散的誤差控制定理和一種帶誤差約束的b樣條曲線的自動光順方法； （ 2 ）提出了一種基於相鄰層輪廓相似性的醫學斷層輪廓數據曲面重構方法； （ 3 ）提出了一種稱為「虛擬測量」的曲面模型處理方法。On the base of determination of corresponding points between adjacent sections, dissimilar segments are separated to construct spatial dissimilar polygons. then triangular mesh interpolating the cross sections are obtained by tiling the dissimilar polygons and similar segments
在確定相鄰層輪廓對應點的基礎上，將不相似部分分離出來並跟蹤不相似部分構成不相似多邊形，然後分別對相似部分和不相似部分進行三角化，得到三角網格模型。Secondly, the problem of the curve - surface mutual transforming and smooth - finishing have been analyzed farther. for the surface intersecting problem : owing to the introduction of the boundary points, as long as the intersecting points on a certain line, the full intersecting line can be gained. the intersecting line either intersects at the boundary of the triangle surface or forms the loop ; during the course of tracking, the selecting of the pace is restricted by the curvature, the number of the gained intersecting points are not in proportion as the chord - length ; the intersecting points not only record the coordinate and store the parameter
對兩曲面求交問題，當曲面細化足夠小時，曲面求交可近似看成曲面與平面相交問題，引進了邊界點的概念，因此只要知道交線上的任意點，就可以將跨越許多曲面片的整條交線計算出來，所求出的交線或者跨越曲面的邊界，或者形成交線環；從初始點出發跟蹤求解整條交線的過程中，步長的選擇採用了通過曲面片曲率來約束的方法，用該方法求出的交點在不同曲面片上的分佈數目不與弦長成正比；該求交方法包含了各曲面片的邊界線與交線的交點的求解，可獲得邊界交點的坐標值及其參數值。A force diagram representation of polygons was presented to measure the similarity between the two polygons by matching their projection ratios of the force diagram
摘要提出了一種基於力學的多邊形描述方法，並根據多邊形的力圖投影變化曲線的匹配程度度量多邊形之間的相似性，由此實現多邊形的識別與檢索。分享友人