破裂型式 的英文怎麼說

中文拼音 [pòlièxíngshì]
破裂型式 英文
fracture pattern
  • 破 : Ⅰ動詞1 （完整的東西受到損傷） be broken; be damaged 2 （使損壞） break; break down; damage 3 （使...
  • 裂 : 裂動詞[方言] （東西的兩部分向兩旁分開） open
  • 式 : 名詞1 （樣式） type; style 2 （格式） pattern; form 3 （儀式; 典禮） ceremony; ritual 4 （自然科...
  • 破裂 : break; fracture; burst; split; rupture; crack
  1. Stability of rock slopes is generally controlled by the structure of rock masses, especially the soft structure surfaces. analysis of rock mass structures is a key to establish geological models and numerical simulation and a foundation to assess the stability of rock slopes. the weak structure surfaces are mainly bedding planes, faults, joints, schistosity plane and contact zones of intrusive bodies. since they are different in genesis and scale, the rock masses are different in features and mechanical intensities. based on the combination of rock structure bodies, 15 basic modes of deformation and failure of rock slope are systematically summarized. the deformation and failure of rock masses actually result from the recombination and rearrangement of these rock bodies. there are 11 types of rock mass structures and various deformation and failure of bank slopes are present in the reservoir area of the three gorge project

    巖體結構，特別是軟弱結構面對基巖斜坡變形與破壞具有顯著的控製作用，巖體結構模式分析是建立斜坡地質模型和數學模型的關鍵和評價斜坡穩定性的基礎。巖層層面斷裂構造節理裂隙片理與劈理以及侵入體和圍巖的接觸帶等是控制基巖斜坡穩定的軟弱結構面，這些成因不同大小不一的結構面將巖體分割成性質各異力學強度不均的各種巖體結構體，構成了15種基巖斜坡變形破壞的巖體結構基本模式。不同結構體的重新組合與排列是斜坡失穩的內在原因。
  2. The corbel ' s dimension should be ascertained as the manipulative condition of diagonal section. the amount of longitudinal reinforcement be ascertained on the basis of the flexure model, is obtained according to static for balance condition, the calculative expression of the load is obtained. and in terms of the design method in ultimate state the maximum load

    我國規范對于牛腿的設計規定，牛腿尺寸的確定以斜截面抗裂作為控制條件，縱筋用量的確定以彎壓破壞模型為基礎，根據靜力平衡條件得到承載力的計算公式，按照極限狀態設計方法計算得到，箍筋用量則按照構造要求確定。
  3. Study on fracture pattern of open surface - flaw in gabbro

    輝長巖中張開型表面裂隙破裂模式研究
  4. Based on the experiment results, the damage form of abnormal exterior joint are summarized, characteristics of hysteresis curve are studied, the effect of stirrup ratio and height of column section and beam section on anti - shear property of abnormal joint are discussed, working mechanism of abnormal exterior joint is researched, the conclusion that the anti - crack and bearing capacity of abnormal joint are studied by analyzing the minor core of abnormal exterior joint is proposed, the basic data is provided for the design formula of abnormal joints

    根據試驗結果，總結了異型邊節點的破壞形態，研究了節點滯回曲線的特徵，討論了節點核芯配箍率、樑柱截面高度變化對異型邊節點抗剪性能的影響，分析了異型邊節點的受力機理，提出應以「小核芯」為分析單元來研究此類節點抗裂和承載力的建議，為異型節點設計公式的建立提供了基礎數據。
  5. They are expanding model of the bomb body, bursting model of the bomb body and motion model of the fragments. according to the models, the paper gives a detailed algorithm for the whole process of the bomb explosion. ( 7 ) based on the explosion mechanism and the stochastic characteristic of the shell, the paper advances some reasonable hypotheses and supposes that the explosion process of the shell is a markov process, thus constitutes two explosion models of the shell : the imitation model an

    （刀從爆炸的機理出發，利用合理的假設，將殼體的爆炸過程處理為馬爾可夫過程，把爆炸的機理同爆炸的隨機性聯系在一起，建立了殼體爆炸的兩種模型:模擬模型和簡化模型，提出了破裂程度的倍密度函數和破裂方向的倍密度函數兩個概念，得到了基於半邊結構的虛擬殼體爆炸過程中任一條邊出現裂縫的概率公式。
  6. 2. because the fracture mode of 3d braided cmc is the interfacial fracture of mode i and mode ii, energy release rate gc and complex stress intensity factor kc was designated as characterization parameters of fracture toughness in the linear fracture theories. 3

    根據三維編織c sic復合材料斷裂韌性的表徵問題屬于線彈性理論范疇以及材料斷裂模式是界面損傷破壞模式的實驗研究結果，提出了該材料的表徵參量應該使用與界面相關的型和型混合斷裂的能量釋放率g _ c ，或者使用復應力強度因子k _ c 。
  7. This paper analyses the stress and deformation of the two lining structure types of the surge shaft surrounded with crush rock under the action of high water pressure by using fem, compares the two lining types ' s merits and demerits in stress, deformation, fracture state, the combining bearing of surrounding rock and lining structure, the safety and economics

    本文針對圍巖條件比較破碎，裂隙發育的調壓井洞室結構，就兩種襯砌結構型式分別進行了高水頭作用下的有限元數值模擬，從調壓井襯砌結構選型角度分析對比了兩種襯砌結構型式在圍巖及襯砌結構應力與變形、襯砌結構鋼筋混凝土開裂、圍巖與襯砌結構聯合承載、結構安全儲備、經濟等方面的優劣。
  8. Based on the pseudo - static experimental results of nine abnormal joints, the damage process of abnormal joint is divided into four stages of original crack, entire crack, ultimate state and failure, the effect of axial force ratio, stirrup ratio and height of column section on seismic behavior of abnormal joint are discussed, the conclusion that anti - shear capacity of abnormal joint are studied in entire crack state by studying the minor core of abnormal joint is made, the calculating formula for anti - shear capacity of abnormal joint is proposed with a view to asymmetry in stirrup yield

    摘要根據9個鋼筋混凝土框架異型節點試件的擬靜力試驗結果，指出異型節點受力過程分為初裂、通裂、極限和破壞4個階段；討論了軸壓比、節點核芯配箍率、柱截面高度變化對異型節點抗剪性能的影響；提出應考慮節點核芯區箍筋屈服的不均勻性並在通裂狀態下以「小核芯」為分析單元來研究此類節點抗剪承載力的建議；最終給出了異型節點抗剪承載力的計算公式。
  9. Simultaneity, through contrast analysis validate that antiseimic capacity of expansion web is better than that of steel web. therefore, based on the experiences summed up by precedence, the formulation for calculating the crack load and limit load of brick masonry house reinforced by expansion web is advanced, which provides project reference. based on the analysis and studies of masonry shearing strength, test of prestressed single brick masonry wall, and test of prestressed brick masonry house models, and ect, the article has carried through several aspect research as below : 1. a series of experiment on material capability of expansion web, including intensity of single thread and expansion web, ect ; 2. research on influence of loading and destroy of masonry brick building reinforced by expansion web under lowcyclic loading ; 3. study of impact of expansion web on ductility, energy dissipation, intensity, ect under the same situation as above ; 4. put forward computation formulation of masonry brick building reinforced by expansion web

    本著以上的研究目的，本文在分析和借鑒前人砌體抗剪強度理論、預應力單片墻試驗研究、預應力模型抗震性能試驗研究等基礎上，進行了以下幾方面的研究工作: 1 .作為一種新型結構材料擴張網，進行了一系列的材性試驗（單絲強度、網片強度和在砂漿中被約束條件下的網片強度及其相應的彈性模量） ； 2 .研究了水平荷載往復作用（低周交變）下，普通鋼絲網和擴張網砂漿對砌體結構抗裂及承載能力和破壞形態的影響，並將這兩種材料的加固效果進行了對比； 3 .上述狀態下，兩種網片水泥砂漿對砌體結構變形、延性、耗能、剛度退化等抗震性能的影響及其影響效果的比較； 4 .提出擴張網水泥砂漿加固砌體結構的抗剪強度計算建議公式。
  10. According to the geological survey on no. 316 national road from zaoyang to shuhe in the southern shaanxi province, five deformation and failure patterns of the slope in soft metamorphic rock are concluded and analyzed in detail, for effective forecast and economical treatment of slope hazard

    本文通過對陜南316國道早陽蜀河段的實地調查，歸納了該路段軟弱變質巖邊坡的變形破壞特徵，總結出順層滑動、彎曲傾倒、楔形體滑動、潰曲破壞以及滑移拉裂5種典型的病害模式，並對每種變形破壞模式進行了具體的實例分析，從而為邊坡成災預警和選擇經濟有效的治理對策奠定基礎。
  11. According to the geological conditions of baise project, erosive bands and joint fissures, f6 fault and grout curtain are fully simulated to establish 3d numerical model of the dam and its foundation. 3d non - linear fem is used to analyze the stress and strain and to appraise the operation state of both the dam and it ' s foundation under different operation conditions. by overloading the upstream water level and reducing rock strength parameter, the dam foundation ' s degradation process is simulated and the damage pattern and paths are determined, and finally the safety factor is determined

    2 、根據百色的地形地質條件，充分模擬了蝕變帶、節理裂隙、 f6斷層、灌漿帷幕等，較為真實地建立了壩體與地基相互作用的整體三維數值模型；採用有限元法對壩體及壩基在不同工況下的應力應變狀態開展分析，評價各工況下壩基的運行狀態；而後採用超載法和綜合法對大壩穩定性進行分析，模擬壩基的漸進性破壞過程，從而得到壩基在超載和強度下降過程中的破壞模式和破壞發展路徑，最終確定壩基超載安全系數和綜合安全系數。
  12. Through imitated to experiment to the physics of the typical model slopes, it can be found that the k23 + 850 ' s dip slope is belong to creep - sliding and fracturing, that the k47 + 750 ' s scarp slope is belong to bending and fracturing, ( 3 ) it is a effective method by establishing the reasonable geology model, and proceed to study with evaluation of determine the nature and fix quantifying

    通過對典型邊坡的物理模擬試驗，研究發現k23 + 850處中傾順向巖質邊坡變形破壞形式為滑移?拉裂型，而k47 + 750處的陡傾內反向巖質邊坡的變形破壞形式為彎曲?拉裂型。其次是建立合理的地質模型，對邊坡進行定性及定量評價。
  13. Typical examples include the xidatan palaeo - seismic fracture zone, seismic fracture zone of the kunlun ms 8. 1 earthquake occurred in november 14, 2001, the south hohxil palaeo - seismic fracture zone, seismic fracture zone of the bengcuo ms 8. 0 earthquake occurred in 1951 and seismic fracture zones along normal fault in east of the nyainqentanglha mts. caused by jiuzila ms 7. 5 earthquake occurred in 1952 and yangbajain ms 8. 0 earthquake occurred in 1411

    典型地震破裂包括西大灘古地震破裂、昆侖山南緣地震破裂、可可西里古地震破裂、崩錯地震破裂、谷露盆西地震破裂、羊八井當雄盆西地震破裂；地震破裂規模大，產狀穩定，與地震鼓包、地震陡坎、地震凹陷有序組合，是地表構造變形的重要形式，屬內動力成因地裂縫。
  14. In the paper, on the basis of expounding the importance of similarity theory in the numerical simulation of tectonic stress field, it is pointed out that, only by making the numerical model be similar to the geological prototype in material, combination pattern, boundary condition, loading mode and cracking criterion, etc., may the simulation result be real

    摘要論述了在構造應力場模擬中相似性原理的重要性，指出地質原形與數值模型在材料、組合形式、邊界條件、受力方式和破裂準則等方面必須相似，模擬的結果才具有真實性。
  15. The proposed model - beam - particle model is validated to simulate some routine tests of concrete which including uniaxial compressive test and uniaxial tensile test to prove that the numerical model can effectively to describe the complete failure process caused by the initiation, propagation and coalescence of cracks. the influence of the meso - mechanical properties to the macroscopic failure behavior is discussed in this paper. the proposed model is employed to simulate the dynamic failure process of concrete under impact loading, and analyse the failure behavior of concrete with different impacting velocity

    本文建立了混凝土的梁-顆粒數值模型，並利用該模型進行了混凝土在單軸壓縮和拉伸載荷作用下，混凝土從微裂紋的萌生、擴展、貫通直到宏觀裂紋產生導致破壞的全過程的數值模擬，探討了混凝土材料細觀結構對其宏觀力學行為的影響；利用該數值模型，模擬了鋼彈以一定的初始速率垂直侵徹混凝土圓板的動態過程，對計算結果進行了動畫顯示，並分析了不同鋼彈初始速率對混凝土圓板破壞形式的影響。
  16. One of the main failure patterns is caused by fatigue crack growth, so it is necessary to research material fatigue crack growth rate. so for, it is still a difficult problem to measure crack length at elevated temperature

    裂紋疲勞擴展導致的破壞成為設備失效的主要型式之一。因此對材料在高溫下疲勞裂紋擴展速率的研究成為工程界的迫切需要。
  17. Fractures in the weld root on column fusion face are typical earthquake damage to steel frames. the object of this paper is computer simulation of typical seismic damage to steel frame structures

    樑柱節點焊縫斷裂是鋼框架結構震害中的典型破壞模式，本課題研究的目標是對鋼框架結構這種典型的震害進行計算機模擬。
  18. Traditional heaters adopt 10u bending welding type so the copper ' s structure changed and becomes easy to break

    一般加熱器，採用幾10u型彎管焊燒式型，銅管因焊燒變質容易破裂。
  19. Crack development and failure modes, longitudinal reinforcement strain distributions and load - deflection curves were compared as a result in order to evaluate the validity of the disturbed stress field model to analyse such deep simply supported beam

    通過與試驗結果的對比，在開裂形態、破壞形式、縱筋應變分佈及荷載位移曲線等局部與整體反應層次上，評價了擾動應力場模型模擬深受彎簡支梁受力性能的適用性。
  20. Esd based on chemical catalytic model is founded and the factors affecting the enterprises " sustainable development are specified. through analyzing organization property of esd, a conclusion is drawn that employee ' s extensive participation and elastic net structure could make the organization respond to external circumstance precisely and quickly. how the main four platforms affect esd is analyzed by construction of esd ' s dynamic supporting mechanism

    構建了企業可持續發展化學催化模型，對影響企業發展的要素進行了定位分析；通過對企業可持續發展的組織特性進行分析，得出了員工廣泛參與式管理和彈性式的網路結構可以使組織對外部環境的快速準確響應的結論；通過建立esd動態支撐機制，分析了四大平臺是如何影響企業持續發展的；最後，結合對稱破裂原理分析了整合管理模型對esd研究的重要意義。
分享友人
分享到 Line

分享到臉書